Premier Mounts MM-CP15 User manual

Page 1 Installation Instructions
Installation Instructions
9531-000-061-00
Parts List
MM-CP15/28/42
(Varied sized pole with clamp)
(Qty 1)
The MM-CP15 is the 15”
single pole for multi-monitor
mounts with clamping base.
The MM-CP28 is the 28”
version, and the MM-CP42 is
the 42” version. These three
different pole sizes provide
more mounting options for
those installing multi-monitor
mounts. The larger the pole,
the more displays that can
be mounted per single base.
Clamp installations are
versatile and attach to desks,
cubicles or any standard
tabletop.
Step 1
Multi-monitor mounts with clamping bases easily secure to a variety of at
surfaces including desks,cubicles, or any standard tabletop.
First, determine where you would like your multi-monitor mount positioned
on your desired surface. The mounting surface should be capable of
supporing 5x the weight of the at-panel and mount. (Mount & at-panel
sold separately)
Step 2
Step 3
3/8” x 1/2” Button Head Screw
(Qty 2)
MM-CP15
MM-CP28
MM-CP42
Allen Key (Qty 1)
Determine your surface thickness, the clamping
base is adjustable from 1” to a maximum of 4”.
1. To adjust to desired size, remove the pre-
installed 3/8” x 1/2” button head screws
with a 6mm allen key (shown in gure 1 to
the right)
2. Reposition them by moving the existing
screw holes on the bottom portion of base
so that they are aligned with one of the 3
pairs of holes in the back bottom portion.
3. Re-install the 3/8” x 1/2” button head
screws through the the back portion and
bottom piece so that the pole and clamp
are secure. 2
1
3
Introduction
MM-CP15/28/42
1. Once the clamp base’s opening is large enough to easily t onto
your desired surface, slide the base onto the surface.
2. The top portion with the pole size you have chose is positioned
above the surface, and the bottom portion with the tightening
screw nobs are below the surface.
3. Twist the screw nobs (one at a time) so that they are
rmly gripping the bottom of of the table and the top
of the base is pressing rmly on the upper surface
(see gure 2 below).
28”
42”
15”
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the
original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be
shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS,
PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM
IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT
RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO,
INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE
PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the
address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem,
the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier Mounts
Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | [phone] | F [phone]

Page 1 Installation Instructions
Installation Instructions
9531-000-011-00
Parts List
MM-A1
Articulating Mounting Arm
(Qty 1)
The MM-A1 is a single articulating multimonitor mount arm that works
with any 2” tube. The mounting head provides 90° of omnidirectional
tilt. and include both 75x75mm and 100x100mm VESA mounting
patterns.The arm includes integrated cable management tabs to keep
wires and cables protected and organized.
Step 1
1. Slide your mounting arm over the pole and base (Figure 1)
(not included, but should be installed).
Determine the position on the pole desired for your mounting arm.
2. Once in desired position,tighten the two (2)
pre-intalled M8 x 6mm set screws in the
holes in the back of the MM-A1. Tighten
with included allen key (Figure 2).
Step 2
M4 x 10mm
Combo Screws
(Qty 4)
Introduction
MM-A1
Figure 1
(Figure 3)
Are you installing to a 75x75mm or
100x100mm VESA moutning pattern?
For 75x75mm, use mounting points A. For
100x100mm use points B in gure 3.
1) Thread the M4 screws to one-half of their
length into the top two mounting holes on
your display, but do not tighten the M4
screws at this time.
Step 3
(Figure 2)
A A
A A
B B
B B
Thread Insert in Flat
Panel or Adapter Plate
M4 Screw Partially
Threaded Into Flat Panel
Keyhole Slot
MM-A1 Mount
1) Insert the heads of the M4 screws through the keyhole slots on the
mounting head (Figure 5).
2) Insert the remaining two (2) M4x10mm screws, into the bottom mounting
points (Figure 4)
3) Tighten all M4 screws.
Do not overtighten the mounting hardware
(Figure 4)
Figure 5
M6 Allen Key
(Qty 1)
Socket Wrench
(Qty 1)
Step 3
To adjust the tension and/or tilt angle of the mounting head:
1) Adjust the mounting head by utilizing the 90°continuous tilt, until it is in the
desired position.
2) Remove the side and bottom cosmetic cap from the mounting
head (Figure 6)
3) Use the supplied socket wrench to tighten both nuts.
4) The side nut secures the tilt position (Point A), while the bottom nut
secures the pivot (Point B).
Do not overtighten the mounting hardware
A
B
(Figure 6)
Bottom View
5/32” Allen Key
(Qty 1)
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | [phone] | F [phone]

Page 2 Installation Instructions
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the
original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS,
PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM
IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS
IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT
LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING
DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the
address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem,
the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier Mounts
Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | [phone] | F [phone]