Premium Tv-4593led User manual

DESCRIPTION OF CONTROL KEYS & CONNECTORS

01 02

Cleaning

Dust the set by wiping the screen and the cabinet with a

soft, clean cloth or some special liquid cleaner.

Do not apply excessive force to the screen when cleaning.

Do not use water or other chemical cleaner to clean the

screen as this may damage the surface of the LCD screen.

Product

Read all of the instructions before operating the set. Keep

these instructions well for future use.

Do not block or cover the ventilation openings on the back

cover.

Do not push objects of any kind into this unit through the

cabinet slots as they could touch the current carrying parts

or short-circuit parts, resulting in fire, electric shock, or

damage to the unit.

Do not attempt to open the cabinet as this may cause

damage. There are no parts inside you can service by

yourself. Refer all servicing to qualified personnel.

Do not touch the screen surface with fingers as this may

scratch or mar the LCD screen.

Do not impact the LCD screen with hard pressure as this

may damage the LCD screen severely.

Unplug the set under the following conditions:

- If the set will not be used for a long period of time.

- If the power cord or the power outlet/plug is damaged.

- Follow the instructions to install and adjust the product.

Adjust those controls that are covered in this operating

instructions as improper adjustment of other controls

may result in damage. If this happens, unplug the set

and refer to the service personnel.

- If the set is subject to impact or has been dropped to

Have the cabinet damaged.

Where an all-pole mains switch is used as the disconnect

device, the switch shall remain readily operable.

Power and Plug

Do not allow anything to rest on or roll over the power

cord and the signal cable.

Protect the power cord and the signal cable from being

trampled.

Do not overload the power cord or the power outlet.

Do not expose the power cord and the signal cable to

moisture.

Power Cord and Signal Cable

Do not place the set on an unstable cart, stand, or table.

Place the set on a place that allows good ventilation.

Do not use the set near damp, and cold areas. Protect

the set from overheating.

Keep the set away from direct sunlight.

Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

Do not use the set near dust place.

Use Environment

Hanging the TV Set on the Wall

Warning:

Warning:The batteries shall not be exposed to excessive

heat such as sunshine, fire or the like.

This operation requires two people.

To ensure a safe installation, observe the following safety

notes:

Check that the wall can support the weight of the TV set

and wall mount assembly.

Follow the mounting instructions provided with the wall

mount.

The TV set must be installed on a vertical wall.

only screws suitable for the material of

TV set cables are placed so that there

is not danger of tripping over them.

instructions about our TV sets are also

Make sure to use

the wall.

Make sure that the

All other safety

applicable here.

Precautions

72-D20MDL-E00

Note

Graphics contained within this publication are presentation

only.

Design and specifications are subject to change

without notice.

If there is any difference between the

descriptions in our manual and the actual operation,

refer to the actual operation as a standard.

Most problems you encounter with your TV can be corrected

by consulting the following troubleshooting list.

No picture, no sound

1. Check if the fuse or circuit breaker is working.

Plug another electrical device into the outlet to make sure

it is working or turned on.

3. Power plug is in a bad contact with the outlet.

4. Check the signal source.

No color

1. Change the color system if it is available.

2. Adjust the saturation.

Try another channel. Black-white program may be received.

Remote control does not work

1. Change the batteries.

2. Batteries are not installed correctly.

3. Main power is not connected.

No picture, normal sound

1. Adjust the brightness and contrast.

2. Broadcasting failure may happen.

Normal picture, no sound

1. Press the Vol+ button to increase volume.

2. Volume is set to mute, press the mute button to restore

sound.

3. Change the sound system if it is available.

4. Broadcasting failure may happen.

Unorderly ripples on the picture

It is usually caused by local interference, such as cars,

daylight lamps and hair driers. Adjust the antenna to minimize

the interference.

Blank screen in VGA mode

Perhaps the TV can not recognize the resolution set by the PC.

Suggest to change to the best resolution or other standard

resolutions of the Windows system.

Snowy dots and interference

If the antenna is located in the fringe area of a television

signal where the signal is weak, the picture may be marred

by dots. When the signal is extremely weak, it may be necessary

to install a special antenna to improve the reception.

1. Adjust the position and orientation of the indoor/outdoor

antenna.

2. Check the connection of antenna.

3. Fine tune the channel.

4. Try another channel. Broadcasting failure may happen.

Ignition

Black spots or horizontal streaks appear, or the picture flutters

or drifts. This is usually caused by interference from car ignition

system, neon lamps, electric drills, or other electrical appliance.

Ghost

Ghosts are caused by the television signal following two paths.

One is the direct path, the other is reflected from tall buildings,

hills, or other objects. Changing the direction or position of the

antenna may improve the reception.

Radio frequency interference

This interference produces moving ripples or diagonal streaks,

and in some case, loss of contrast in the picture. Find out and

remove the radio interference source.

Troubleshooting

Panel Buttons

Sockets

HDMI INPUT

HDMI

VGA INPUT

VGA IN

ANTENNA

ANTENNA INPUT

Note: 1) the audio input of YPbPr , VGA and HDMI-DVI share the same

socket with AV2.

2) VGA input corresponds to the PC option in the unit.

CHANNEL UP button

Scans up through the channel list. In the menu system, it points up to items and adjusts menu controls.

CH.

MENU button

Brings up the menu system.

SOURCE button

Brings up the signal source selection menu.

SOURCE

Button

Turns off the unit to the standby mode or turns on the unit in the standby mode.

CHANNEL DOWN button

Scans down through the channel list. In the menu system, it points down to items and adjusts menu controls.

CH.

VOLUME UP button

Increases the volume. In the menu system, it points right to items and adjusts menu controls.

VOL.

VOLUME DOWN button

Decreases the volume. In the menu system, it points left to items and adjusts menu controls.

VOL.

V L R

AV2 IN

YPb Pr

Component

VLR

AV IN

YPbPr/YUV INPUT

AV2 INPUT AV1 INPUT

USB INPUT

USB

DC INPUT

V L R

AV OUT

AV OUTPUT

Base Installation

1) Insert the support into the unit.(as fig1)

2) Fix the base by three screws.(as fig2)

Fig1

Fig2

Note: Align withe the center of the three holes.

OPERATION MANUAL

LCD TV

DESCRIPTION OF CONTROL KEYS & CONNECTORS

01 02

Cleaning

Dust the set by wiping the screen and the cabinet with a

soft, clean cloth or some special liquid cleaner.

Do not apply excessive force to the screen when cleaning.

Do not use water or other chemical cleaner to clean the

screen as this may damage the surface of the LCD screen.

Product

Read all of the instructions before operating the set. Keep

these instructions well for future use.

Do not block or cover the ventilation openings on the back

cover.

Do not push objects of any kind into this unit through the

cabinet slots as they could touch the current carrying parts

or short-circuit parts, resulting in fire, electric shock, or

damage to the unit.

Do not attempt to open the cabinet as this may cause

damage. There are no parts inside you can service by

yourself. Refer all servicing to qualified personnel.

Do not touch the screen surface with fingers as this may

scratch or mar the LCD screen.

Do not impact the LCD screen with hard pressure as this

may damage the LCD screen severely.

Unplug the set under the following conditions:

- If the set will not be used for a long period of time.

- If the power cord or the power outlet/plug is damaged.

- Follow the instructions to install and adjust the product.

Adjust those controls that are covered in this operating

instructions as improper adjustment of other controls

may result in damage. If this happens, unplug the set

and refer to the service personnel.

- If the set is subject to impact or has been dropped to

Have the cabinet damaged.

Where an all-pole mains switch is used as the disconnect

device, the switch shall remain readily operable.

Power and Plug

Do not allow anything to rest on or roll over the power

cord and the signal cable.

Protect the power cord and the signal cable from being

trampled.

Do not overload the power cord or the power outlet.

Do not expose the power cord and the signal cable to

moisture.

Power Cord and Signal Cable

Do not place the set on an unstable cart, stand, or table.

Place the set on a place that allows good ventilation.

Do not use the set near damp, and cold areas. Protect

the set from overheating.

Keep the set away from direct sunlight.

Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

Do not use the set near dust place.

Use Environment

Hanging the TV Set on the Wall

Warning:

Warning:The batteries shall not be exposed to excessive

heat such as sunshine, fire or the like.

This operation requires two people.

To ensure a safe installation, observe the following safety

notes:

Check that the wall can support the weight of the TV set

and wall mount assembly.

Follow the mounting instructions provided with the wall

mount.

The TV set must be installed on a vertical wall.

only screws suitable for the material of

TV set cables are placed so that there

is not danger of tripping over them.

instructions about our TV sets are also

Make sure to use

the wall.

Make sure that the

All other safety

applicable here.

Precautions

72-D20MDL-E00

Note

Graphics contained within this publication are presentation

only.

Design and specifications are subject to change

without notice.

If there is any difference between the

descriptions in our manual and the actual operation,

refer to the actual operation as a standard.

Most problems you encounter with your TV can be corrected

by consulting the following troubleshooting list.

No picture, no sound

1. Check if the fuse or circuit breaker is working.

Plug another electrical device into the outlet to make sure

it is working or turned on.

3. Power plug is in a bad contact with the outlet.

4. Check the signal source.

No color

1. Change the color system if it is available.

2. Adjust the saturation.

Try another channel. Black-white program may be received.

Remote control does not work

1. Change the batteries.

2. Batteries are not installed correctly.

3. Main power is not connected.

No picture, normal sound

1. Adjust the brightness and contrast.

2. Broadcasting failure may happen.

Normal picture, no sound

1. Press the Vol+ button to increase volume.

2. Volume is set to mute, press the mute button to restore

sound.

3. Change the sound system if it is available.

4. Broadcasting failure may happen.

Unorderly ripples on the picture

It is usually caused by local interference, such as cars,

daylight lamps and hair driers. Adjust the antenna to minimize

the interference.

Blank screen in VGA mode

Perhaps the TV can not recognize the resolution set by the PC.

Suggest to change to the best resolution or other standard

resolutions of the Windows system.

Snowy dots and interference

If the antenna is located in the fringe area of a television

signal where the signal is weak, the picture may be marred

by dots. When the signal is extremely weak, it may be necessary

to install a special antenna to improve the reception.

1. Adjust the position and orientation of the indoor/outdoor

antenna.

2. Check the connection of antenna.

3. Fine tune the channel.

4. Try another channel. Broadcasting failure may happen.

Ignition

Black spots or horizontal streaks appear, or the picture flutters

or drifts. This is usually caused by interference from car ignition

system, neon lamps, electric drills, or other electrical appliance.

Ghost

Ghosts are caused by the television signal following two paths.

One is the direct path, the other is reflected from tall buildings,

hills, or other objects. Changing the direction or position of the

antenna may improve the reception.

Radio frequency interference

This interference produces moving ripples or diagonal streaks,

and in some case, loss of contrast in the picture. Find out and

remove the radio interference source.

Troubleshooting

Panel Buttons

Sockets

HDMI INPUT

HDMI

VGA INPUT

VGA IN

ANTENNA

ANTENNA INPUT

Note: 1) the audio input of YPbPr , VGA and HDMI-DVI share the same

socket with AV2.

2) VGA input corresponds to the PC option in the unit.

CHANNEL UP button

Scans up through the channel list. In the menu system, it points up to items and adjusts menu controls.

CH.

MENU button

Brings up the menu system.

SOURCE button

Brings up the signal source selection menu.

SOURCE

Button

Turns off the unit to the standby mode or turns on the unit in the standby mode.

CHANNEL DOWN button

Scans down through the channel list. In the menu system, it points down to items and adjusts menu controls.

CH.

VOLUME UP button

Increases the volume. In the menu system, it points right to items and adjusts menu controls.

VOL.

VOLUME DOWN button

Decreases the volume. In the menu system, it points left to items and adjusts menu controls.

VOL.

V L R

AV2 IN

YPb Pr

Component

VLR

AV IN

YPbPr/YUV INPUT

AV2 INPUT AV1 INPUT

USB INPUT

USB

DC INPUT

V L R

AV OUT

AV OUTPUT

Base Installation

1) Insert the support into the unit.(as fig1)

2) Fix the base by three screws.(as fig2)

Fig1

Fig2

Note: Align withe the center of the three holes.

OPERATION MANUAL

LCD TV

DESCRIPTION OF CONTROL KEYS & CONNECTORS

01 02

Cleaning

Dust the set by wiping the screen and the cabinet with a

soft, clean cloth or some special liquid cleaner.

Do not apply excessive force to the screen when cleaning.

Do not use water or other chemical cleaner to clean the

screen as this may damage the surface of the LCD screen.

Product

Read all of the instructions before operating the set. Keep

these instructions well for future use.

Do not block or cover the ventilation openings on the back

cover.

Do not push objects of any kind into this unit through the

cabinet slots as they could touch the current carrying parts

or short-circuit parts, resulting in fire, electric shock, or

damage to the unit.

Do not attempt to open the cabinet as this may cause

damage. There are no parts inside you can service by

yourself. Refer all servicing to qualified personnel.

Do not touch the screen surface with fingers as this may

scratch or mar the LCD screen.

Do not impact the LCD screen with hard pressure as this

may damage the LCD screen severely.

Unplug the set under the following conditions:

- If the set will not be used for a long period of time.

- If the power cord or the power outlet/plug is damaged.

- Follow the instructions to install and adjust the product.

Adjust those controls that are covered in this operating

instructions as improper adjustment of other controls

may result in damage. If this happens, unplug the set

and refer to the service personnel.

- If the set is subject to impact or has been dropped to

Have the cabinet damaged.

Where an all-pole mains switch is used as the disconnect

device, the switch shall remain readily operable.

Power and Plug

Do not allow anything to rest on or roll over the power

cord and the signal cable.

Protect the power cord and the signal cable from being

trampled.

Do not overload the power cord or the power outlet.

Do not expose the power cord and the signal cable to

moisture.

Power Cord and Signal Cable

Do not place the set on an unstable cart, stand, or table.

Place the set on a place that allows good ventilation.

Do not use the set near damp, and cold areas. Protect

the set from overheating.

Keep the set away from direct sunlight.

Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

Do not use the set near dust place.

Use Environment

Hanging the TV Set on the Wall

Warning:

Warning:The batteries shall not be exposed to excessive

heat such as sunshine, fire or the like.

This operation requires two people.

To ensure a safe installation, observe the following safety

notes:

Check that the wall can support the weight of the TV set

and wall mount assembly.

Follow the mounting instructions provided with the wall

mount.

The TV set must be installed on a vertical wall.

only screws suitable for the material of

TV set cables are placed so that there

is not danger of tripping over them.

instructions about our TV sets are also

Make sure to use

the wall.

Make sure that the

All other safety

applicable here.

Precautions

72-D20MDL-E00

Note

Graphics contained within this publication are presentation

only.

Design and specifications are subject to change

without notice.

If there is any difference between the

descriptions in our manual and the actual operation,

refer to the actual operation as a standard.

Most problems you encounter with your TV can be corrected

by consulting the following troubleshooting list.

No picture, no sound

1. Check if the fuse or circuit breaker is working.

Plug another electrical device into the outlet to make sure

it is working or turned on.

3. Power plug is in a bad contact with the outlet.

4. Check the signal source.

No color

1. Change the color system if it is available.

2. Adjust the saturation.

Try another channel. Black-white program may be received.

Remote control does not work

1. Change the batteries.

2. Batteries are not installed correctly.

3. Main power is not connected.

No picture, normal sound

1. Adjust the brightness and contrast.

2. Broadcasting failure may happen.

Normal picture, no sound

1. Press the Vol+ button to increase volume.

2. Volume is set to mute, press the mute button to restore

sound.

3. Change the sound system if it is available.

4. Broadcasting failure may happen.

Unorderly ripples on the picture

It is usually caused by local interference, such as cars,

daylight lamps and hair driers. Adjust the antenna to minimize

the interference.

Blank screen in VGA mode

Perhaps the TV can not recognize the resolution set by the PC.

Suggest to change to the best resolution or other standard

resolutions of the Windows system.

Snowy dots and interference

If the antenna is located in the fringe area of a television

signal where the signal is weak, the picture may be marred

by dots. When the signal is extremely weak, it may be necessary

to install a special antenna to improve the reception.

1. Adjust the position and orientation of the indoor/outdoor

antenna.

2. Check the connection of antenna.

3. Fine tune the channel.

4. Try another channel. Broadcasting failure may happen.

Ignition

Black spots or horizontal streaks appear, or the picture flutters

or drifts. This is usually caused by interference from car ignition

system, neon lamps, electric drills, or other electrical appliance.

Ghost

Ghosts are caused by the television signal following two paths.

One is the direct path, the other is reflected from tall buildings,

hills, or other objects. Changing the direction or position of the

antenna may improve the reception.

Radio frequency interference

This interference produces moving ripples or diagonal streaks,

and in some case, loss of contrast in the picture. Find out and

remove the radio interference source.

Troubleshooting

Panel Buttons

Sockets

HDMI INPUT

HDMI

VGA INPUT

VGA IN

ANTENNA

ANTENNA INPUT

Note: 1) the audio input of YPbPr , VGA and HDMI-DVI share the same

socket with AV2.

2) VGA input corresponds to the PC option in the unit.

CHANNEL UP button

Scans up through the channel list. In the menu system, it points up to items and adjusts menu controls.

CH.

MENU button

Brings up the menu system.

SOURCE button

Brings up the signal source selection menu.

SOURCE

Button

Turns off the unit to the standby mode or turns on the unit in the standby mode.

CHANNEL DOWN button

Scans down through the channel list. In the menu system, it points down to items and adjusts menu controls.

CH.

VOLUME UP button

Increases the volume. In the menu system, it points right to items and adjusts menu controls.

VOL.

VOLUME DOWN button

Decreases the volume. In the menu system, it points left to items and adjusts menu controls.

VOL.

V L R

AV2 IN

YPb Pr

Component

VLR

AV IN

YPbPr/YUV INPUT

AV2 INPUT AV1 INPUT

USB INPUT

USB

DC INPUT

V L R

AV OUT

AV OUTPUT

Base Installation

1) Insert the support into the unit.(as fig1)

2) Fix the base by three screws.(as fig2)

Fig1

Fig2

Note: Align withe the center of the three holes.

OPERATION MANUAL

LCD TV

05 06

Canadian English Rating

CE_E

CE_

This program is not suitable for any children and baby.

C (Children): Programming intended for children under age 8.

C8 (Children 8 and Older): Programming generally considered acceptable

for children 8 years and over to watch on their own.

G (General Audience): Programming considered acceptable for all ages

groups.

PG (Parental Guidance): Programming intended for a general audience

but which may not be suitable for younger children (under the age of 8).

14 (Viewers 14 and over): Programming contains themes or content

which may not be suitable for viewers under the age of 14.

18 (Adults): Programming intended for adults 18 and older.

Canadian French Rating

CF_E This program is not suitable for any children and baby.

CF_G (General Audience) This program is suitable for audiences of all

ages.

CF_8 ANS (Viewers 8 and over) Not recommended for young children.

CF_13 ANS (Viewers 13 and over) Programming may not be suitable for

children under the age of 13.

CF_16 ANS (Viewers 16 and over) Programming is not suitable for those

under age 16.

CF_18 ANS (Adults) Programming is for adults only.

Block MPAA Unrated:

select Yes or No to lock or open the unrating movie.

Block TV None Rating:

select Yes or No to lock or open the unrating TV.

Note: CCD and Parent lock are available in the TV and AV mode.

BASIC OPERATION

Access Menu

The MENU, , , OK and numeric buttons use to navigate the menu.

Press MENU button to access the menu or return to the previous menu or

close the menu step by step.

Press EXIT button to quit the menu.

Press button to move the cursor to select option.

Press or OK button to enter the select option

Press button to adjust value or set option.

Press numeric button to enter the program NO..

Picture

The Picture menu is used to adjust the picture settings. You can easy

adjusting these settings to define your own preferred picture.

adjusting the brightness of the picture .

adjusting the difference between the light and dark areas of

the picture.

COLOR: adjusting the picture color.

adjusting the crispness of the edges in the picture.

TINT: adjusting the color.

Note: only in the NTSC mode, it is available.

the left or right

button to scroll through the color settings: COOL for a more blue

palette of picture colors; NORMAL ; and WARM for a more red palette of

picture colors

BRIGHTNESS:

CONTRAST:

SHARPNESS:

COLOR TONE: adjusting the color tone of the picture. Use

direction

FLESH TONE: correcting the color of the picture.

Sound

The Sound menu is used to adjust the sound.

VOLUME: increasing or reducing the volume.

BALANCE: using the left or right direction button to balance the sound

between the left and right speaker to best suit your listening position.

EQUALIZER: using this function to get the better quality of volume.

AVC: For some channel, the volume is low or high, by the function, the

volume may be amended.

MODE: scrolling through the available audio types, which control the way

the sound comes through your speakers. The personal setting is saved

according to changes you make to BASS and/or TREBLE setting.

SURROUND: using this function to switch the unit to the best surround

sound mode, select On or Off.

Setup

The Setup menu is used to adjust the set.

a start-up sound when the TV is turned on.

CHILD LOCK: the child lock function is used to lock the buttons on the

front panel of the TV. When the Child lock is set to On , all the buttons on

the local front panel are locked. But you can still use the Power button on

the front panel to turn on/off the TV.

Reset: selecting On, renew the unit to the factory setup.

LANGUAGE: selecting the OSD language.

COLOR SYSTEM: selecting an appropriate color system using the left

or right direction button.

BLUE BACK: selecting On, the color of background is blue when it is no

signal.

MELODY: selecting

BASIC OPERATION

The Channel menu is used to adjust the set.

Tuner Mode: using this function to select the signal source between cable

and air.

CH. Setting allows you to lock a channel or skip a channel

Auto Store: enter the Installation menu and select Auto store, then press

OK or the right button to start the auto searching.

NOTE:

While searching is going on, press the MENU button can quit the searching.

CCD:

Select the Cur. Channel. Press the left or right button or use the numerical

buttons to select the channel that you want to lock or skip.

Select the channel Lock. Press the left or right button to select On or Off.

When select to On, the selected channel will be locked and if you want to

watch, you have to enter the password 0000.

Select the Skip. Press the left or right button to select On or Off. When set to

On, the selected channel will be skipped if you use the channel up or down

button. But you can still access the channel by using the numerical button.

Closed captioning (CC) lets you read the voice content of TV programs

on the TV screen. Designed to help the hearing impaired, on-screen text boxes

will show dialog, conversation, and activity during TV programming.

Enter the CC MODE menu, Press left or right direction button to cyclically

select CC 1, CC 2, CC 3, CC 4, TXT 1,TXT 2, TXT 3, TXT 4 or CC mute and off.

Preset Channel

APP Function

DNR: using this function for getting the better picture in some sources.

BACK LIGHT: adjusting the back light by selecting normal, sunshine and

energy saving.

ALC: using this function for getting the better picture.

CHANGE PASSWORD: Enter the password0000 to enter the submenu, then

press the new password that you want twice.

USB SETUP: this unit is fitted with a USB connector that enables you to

view photos(only support JPG&BMP), listen to music(only support MP3) or

read book(only support TXT) stored on a USB storage device.

After connect the USB device to the USB port on the side of the TV, you can

use the function.

Press the source button to display the source main menu ,then press the up

or down button to select the USB, press the OK or right button to enter the

USB submenu,

press the OK or right button to confirm your selection.

Note: 1)Press the left button to exit the last menu.

2)When enter the USB menu, press the EXIT button, you can press

the left or right button to select folder, music, picture or text. Press OK button

to confirm your selection, at this time ,only selected kind files can be displayed

on the screen. you can press the up or down direction button to select it and

press the Ok or right button to play it.

To adjust the picture and sound feature to select Pic. Repeat, Pic. Interval,

Photo Mode or Sound Repeat.

Pic. Repeat : Press left or right button to select the Pic. Repeat.

Pic. Interval : Press left or right button to select the time of Pic. Interval .

Photo Mode: Press left or right button to select the Photo Mode.

Sound Repeat : Press left or right button to select the Sound Repeat.

The APP menu is used to adjust the set.

BASIC OPERATION

HDMI

USB USB 01

Source

AV 1

AV 2

YPbPr

Device List

Preset Channel

Parent Lock:

Parental lock is a feature that lets the TV receive and process data sent by

broadcasters or other program providers with program content advisory.

When programmed by the viewer, a TV with Parental lock can respond to the

content advisory and block program content that may be found objectionable

(such as offensive language, violence, sexual situations, etc.). This feature is

useful for adults to prevent certain types of programs from being viewed by

children.

NOTE: Access the menu, need enter the password 0000.

Rating

G: General Audience - All ages admitted. Suitable for all ages.

PG: Parental Guidance Suggested - Contains material unsuitable for younger

children.

PG-13: Parents Strongly Cautioned - Contains material unsuitable for children

under the age of 13.

R: Restricted - Suitable for adults above 17 years of age only.

NC-17: - No one under the age of 17 will be admitted.

X: Adults Only - Contains one or more of the following: very graphic violence,

very graphic and explicit or indecent sexual acts, very coarse and intensely

suggestive language.

Rating

TV-Y: Designed for a very young audience, including children ages 2-6

TV-Y7: Contains Fantasy Violence (FV). Appropriate for children age 7 and

above who have acquired the development skills needed to distinguish

between make-believe and reality.

TV-G: Suitable for most audiences. Contains little or no violence, no strong l

language, and little or no the sexual dialogue or situations.

TV-PG: Contains material unsuitable for younger children. Could contain

moderate violence (V), some sexual situations (S), infrequent coarse

language (L), or some suggestive dialogue (D).

TV-14: Contains some material unsuitable for children under 14 years of age.

Contains one or more of the following: intense violence (V), intense

sexual situations (S), strong coarse language (L), or intensely

suggestive dialogue (D).

TV-MA: Viewed by adults and therefore may be unsuitable for children under

17. Contains one or more of the following: graphic violence (V),

explicit sexual situations (S), or crude indecent language(L).

The Function is activated only when the contents of the receiving

programs, such as violence and sexual scenes, are encrypted. Locking

automatically locks all the higher ratings.

Press OK button to enter the following menu.

Block MPAA

Block TV

Tuner Mode

Auto Store

Parent Lock

App

Channel

Setup

Sound

Picture CH. Setting

CCD

Cable

Select Adjust Back Menu

App

Channel

Sound

Setup

Picture

Color Tone

Flesh Tone

Brightness

Contrast

Color

Sharpness

Tint

Select Adjust Back Menu

Volume

Balance

Channel

App

Sound

Setup

Picture

AVC

Surround

Equalizer

Mode

Select Adjust Back Menu

Child Lock

Language

Color System

App

Channel

Setup

Sound

Picture Melody

Blue Back

English

Reset

Select Adjust Back Menu

DNR

Backlight

SW Upgrade

Sound ALC

App

Channel

Setup

Picture

Chg Password

Time

Normal

USB Setup

Select Adjust Back Menu

Switching on & off

Press the I on the power button to switch on the TV,

I means switching on the power supply.

Note: In case of any danger, if you do not use this unit ,

you should pull out the plug

For some unit, it is no this button.

When the TV is in the standby mode, press the

or the program up/ down button on the remote control

or unit to switch on the TV.

BASIC OPERATION

Press the 0 on the power button to switch off the TV,

0 means switching off the power supply

When press the button to switch on or switch off

the unit.

Note: For some unit, it is no this button.

Parent Lock

Tuner Mode

CCD

App

Channel

Setup

Sound

Picture Auto Store

CH. Setting Block MPAA Rating

Block TVRating

Canadian English Rating

Block MPAA Unrated

Canadian French Rating

Select Adjust Back Menu

Block TV None Rating

Remote Control Functions

Most of your television's functions are available via the menus that appear on the

screen. The remote control supplied with your set can be used to navigate through

the menus and to configure all the general settings.

For game function, it is depending on the model.

The optional buttons indicated with symbol* depend on the supplied remote control.

Note:

Power button

Press to turn the TV on or off (standby mode).

MUTE button

Press to mute or restore the TV sound.

buttonSource

Brings up the signal source selection menu.

SOURCE

buttonDisplay

Displays the current channel number and other

information on the TV screen.

DISPLAY

Return button

Returns to the previously viewed channel.

RETURN

ZOOM

Zoom button

Selects the scale.

Note: In the YPbPr & HDMI mode, it is available for

the SDTV. In the PC mode, it is unavailable.

In the USB mode, it adjusts the size of the picture.

P. Effect

P. Effect button

Toggles through the picture presetsettings

F1 button

Switches the sound mode in BTSC mode.

F2 button

Enters the preview of picture in USB mode.

In other modes, enters GAME mode.

Menu button

Brings up the menu system, or exit the menu.

S. Effect

S. Effect button

Toggles through the sound modes

F4 button

Displays the next page picture in USB mode.

F3 button

In the TV and AV mode, enter CCD directly.

In USB mode, displays the previous page picture.

EXIT

Exit button

Exits the Menu system.

Numerical buttons

Enters channel numbers.

Channel up/ down buttons:

Scans up or down through the current

channel list.

Up/down/ left/ right direction buttons

Highlights different items in the menu system

and adjusts the menu controls.

In USB mode, press the left or right button to

fast reverse or fast forward.

OK button

Confirms your selection for entering the source, the

submenu etc. .

Volume up/ down buttons

Increases or decreases the TV's volume.

POWER

MUTE

SLEEP

Sleep button

Selects the sleep timer.

TV button

In any source, switches to TV mode.

USB

USB button

In any source, switches to USB mode.

OPTION

OPTION button

it is unavailable.