Pro-face PL-DK210 User manual

-1-
• Be sure to check that the PL unit’s power cord is disconnected before in-
stalling this unit. Failure to do so may cause an electric shock.
• Do not attempt to modify or open the PL-DK210 unit. This may cause a
fire or an electric shock.
• Be sure to read the “2. Installation” section completely to insure that the
PL-DK210 unit is correctly installed.
To Prevent Accidents
• Since the PL-DK210 is a precision instrument, be sure it is neither hit by
nor pressed strongly against another object.
• Be sure water, liquids or metal particles are not allowed to enter this unit's
connector. Any of these may cause either a breakdown or an electric
shock.
• Do not store or operate this unit in a location where there is direct sun-
light, excessive heat, dust or vibration.
• Do not store or operate this unit near chemicals, or where there are chemi-
cal fumes.
• Do not use the PL-DK210 in locations where corrosive gases are present.
• To prevent damage to file data, be sure to shut down the unit's OS before
turning OFF the main power.
Warning - Safety Precautions
The PL-DK210 (CD-ROM Unit) is designed for use with Pro-face's PL
Series Panel Computers, hereafter referred to as the "PL". This unit is the
CD-ROM unit for the PL.While the PL-DK210 provides a convenient way
to install software into the PL's HDD unit, it is not designed to be used
outside of the development environment.
Corresponding Products: PL-X920 Series Units.
Pro-face is the trademark of Digital Electronics Corporation, registered in Japan
and other countries. MS-DOS is the trademark of Microsoft Corporation in the
United States and/or other countries. All other trademarks/registered trade-
marks are the properties of their respective owners.
!
PL-DK210
Installation Guide

-2-
n Installation Guide (1)
n PL−−
−−
−DK210 Unit (1)
Package Contents
n Connection Cable (1)
Please check that the following items are included in your PL-DK210's
package.
n Attachment Screws (8)
n Floppy Disk (1)
Pro-face has taken utmost care to insure the quality of this product when it
was shipped. However, for any reason, should you find any faults or dam-
age, please contact your Pro-face representative immediately for service.
n Front Face Fastener (1) n Rear Face Fastener (1)
∗ 1For instructions and usage of the programs included in the floppy disk
(such as device driver programs, etc.), refer to the README file.
∗1

-3-
1Hardware Specification
n Functional
n Environmental
*1 The PL-DK210's connection cable is a special-purpose cable. Any other
type of cable cannot be used to connect this unit to the PL unit.
AmbientTemperature
5oCto 50oC
Storage Temperature
-10oCto +60oC
AmbientHumidity
10%RHto80%RH(no condensation)
Vibration Resistance
(during operation)2.9m/s2(10Hzto25Hz)
Shock Resistance
(notoperating) 588m/s2
Random Access Seek
140ms(Ave.)
Data TransferSpeed
16.7MB/s(Max.)
Disk Speed
4,280rpm(typ)
Inferface
IDE(ATAPI)*1
During Startup: 0.9A(typ)
During RandomAccess:0.8A(typ)
During Wait:0.5A(typ)
PowerConsumption

-4-
When using the CD-ROM drive unit with the PL-X920 Series unit, be
sure to change the "IDE Primary Master PIO" and "IDE Primary Slave
PIO" settings within the "System Information area | INTEGRATED
PERIPHERALS" to "Mode 2". Also, be sure to set the "IDE Primary
Master UDMA" and "IDE Primary Slave UDMA" settings to "Dis-
abled". PL Series User Manual, Chapter 5 System Setup.
A)Connecting to a PL-X920 (2-Slot) Series Unit
1) Unscrew the IDE I/F cover's two
(2) attachment screws and the
HDD1 slot's two (2) attachment
screws. Remove the IDE I/F cover
and the HDD1 slot cover.
nConnecting to a PL-X920 Series Unit
WARNINGS
Shock Danger! Be sure to unplug the PL unit from its power supply
prior to installing the PL-DK210 unit.
2Installation
Be sure to use the following installation procedures to insure that the PL-
DK210 unit is correctly installed. Installation procedures will differ de-
pending on the type of PL unit you are using.
2) Secure the rear face fastener to the
rear of the PL unit using the two
(2) attachment screws.

-5-
3) Secure the front face fastener to the
PL-DK210 unit using the two (2)
attachment screws.
DC INPUT IDE INTERFACE
#1 pin markCable's #1 pin mark
5) Secure the PL-DK210 unit to the
PL unit using the four (4) attach-
ment screws. Place the cable in the
aperture between the PL-DK210
and PL units.
4) Connect the PL-DK210 unit to the
PL unit via the connection cable.
Be sure to confirm that the Cable's
#1 pin mark and the connector are
correctly aligned.
Do not connect anything
to the DC INPUT Connec-
tor.

-6-
1) Unscrew the IDE I/F cover's two
(2) attachment screws and the
HDD1 slot's two (2) attachment
screws. Remove the IDE I/F cover
and the HDD1 slot cover.
B)Connecting to a PL-X920 (4-Slot) Series Unit
2) Secure the rear face fastener to the
rear of the PL unit using the two (2)
attachment screws.
3) Secure the front face fastener to the
PL-DK210 unit using the two (2)
attachment screws.

-7-
4) Connect the PL-DK210 unit to the
PL unit via the connection cable.
Be sure to confirm that the Cable's
#1 pin mark and the connector are
correctly aligned.
Do not connect anything
to the DC INPUT Connec-
tor.
5) Secure the PL-DK210 unit to the
PL unit using the four (4) attach-
ment screws. Place the cable in the
aperture between the PL-DK210
and PL units.
Caution
Refer to the following drawings to confirm that the connection cable
issecurelyattachedtobothconnectors.Besuretocheckbothconnectors
before turning the PL ON, since incorrect attachment of the connectors
can cause equipment damage.
XX
!
DC INPUT IDE INTERFACE
#1 pin markCable's #1 pin mark

-8-
© 2003 Digital Electronics Corporation All rights reserved.
Note
Please be aware that Digital Electronics Corporation shall not be held
liable by the user for any damages, losses, or third party claims arising
from the uses of this product.
Digital Electronics Corporation
8-2-52 Nanko Higashi, Suminoe-ku, Osaka 559-0031, Japan
URL: http://www.pro-face.com/