Pro-face PSS-CD01 User manual

E-1
• Be sure to check that the PS-A/PL unit’s power cord is disconnected before
installing this unit. Failure to do so may cause an electric shock.
• Do not attempt to modify or open the PSS-CD01. This may cause a fire or an
electric shock.
• Be sure to read the “2. Installation to PS-A” section or “3. Installation to PL”
section completely to insure that the PSS-CD01 is correctly installed.
To Prevent Accidents
• Since the PSS-CD01 is a precision instrument, be sure it is neither hit by nor
pressed strongly against another object.
• Be sure water, liquids or metal particles are not allowed to enter the PSS-
CD01's connector. Any of these may cause either a breakdown or an electric
shock.
• Do not store or operate this unit in a location where there is direct sunlight,
excessive heat, dust or vibration.
• Do not store or operate the PSS-CD01 near chemicals, or where there are
chemical fumes.
• Do not use the PSS-CD01 in locations where corrosive gases are present.
• To prevent damage to file data, be sure to shut down the PS-A/PL unit's OS
before turning OFF the main power.
Unit Disposal
• When the product is disposed of, it should be done so according to your
country's regulations for similar types of industrial waste.
Warning - Safety Precautions
Preface
The PSS-CD01 (CD-ROM Drive Unit) is the designed for use with Pro-face's
Compact Panel Computer PS-3701A(EdenTM ESP6000 - 667MHz Model),
hereafter referred to as the "PS-A" and Panel Computer PL-X920/X930 Series,
hereafter referred to as the "PL". While the PSS-CD01 provides a convenient
way to install software into the PS-A/PL's HDD unit, it is not designed to be
used outside of the development environment.
Corresponding Products: PS-3701A(EdenTM ESP6000 - 667MHz Model), and
PL-X920/X930 Series units.
Pro-face is a trademark of Digital Electronics Corporation, registered in Japan and
other countries. All other trademarks/registered trademarks are the properties of their
respective owners.
!!
!!
!

E-2


Installation Guide (1)
<This Guide>


PSS-CD01 Unit (1)
Package Contents


Connection Cable (1)


 Attachment Screws (8)
Pro-face has taken utmost care to insure the quality of this product when it was
shipped. However, for any reason, should you find any defects or damage,
please contact your Pro-face representative immediately for service.


Front Face Fastener for
PS-A (1)
1Hardware Specifications


 Functional Specifications
*1The PSS-CD01's connection cable is a special-purpose cable. Any other type of
cable cannot be used to connect this unit to the PS-A/PL unit.
Random Access Seek 115ms(Ave.)
Data TransferSpeed 16.7MB/s (Max.)
Disk Speed 5,136rpm(typ)
Inferface IDE (ATAPI)*1
DuringStartup: 1.0A(typ)
During RandomAccess:0.85A(typ)
During Wait:0.45A(typ)
PowerConsumption


Front Face Fastener for
PL (1)


Rear Face Fastener for PL (1)


Rear Face Fastener for PS-A (1)

E-3


 Environmental Specifications
Surrounding Air Temperature +5 oCto +50oC
Storage Temperature -10oC to +60oC
AmbientHumidity 10%RHto 80%RH(nocondensation)
Vibration Resistance (duringoperation)2.9m/s2(10Hzto 25Hz)
Shock Resistance (notoperating) 588m/s2
When using the PSS-CD01 with the PS-A unit, be sure to change the "IDE
Primary Master PIO" and "IDE Primary Slave PIO" settings within the Sys-
tem Information area "INTEGRATED PERIPHERALS" to "Mode 2". Also,
be sure to set the "IDE Primary Master UDMA" and "IDE Primary Slave
UDMA" settings to "Disabled".
Compact Panel Computer PS-3701A(EdenTM ESP6000 -
667MHz Model) User Manual, Chapter 3 System Setup.
WARNINGS
Shock Danger! Be sure to unplug the PS-A unit from its power
supply prior to installing the PSS-CD01.
2Installation to PS-A
Be sure to use the following installation procedures to ensure that the PSS-
CD01 is correctly installed to PS-A.
1) Unscrew the CD-ROM Drive I/F
cover's two (2) attachment screws.
Remove the CD-ROM Drive I/F
cover.
2) Secure the rear face fastener to the
rear of the PS-A unit using the two
(2) attachment screws. The torque
should be 0.5 to 0.6N•m.

E-4
3) Secure the front face fastener to the
PSS-CD01 using the two (2) at-
tachment screws. The torque
should be 0.5 to 0.6N•m.
5) Secure the PSS-CD01 to the PS-A
unit using the four (4) attachment
screws. The torque should be 0.5
to 0.6N•m. Place the cable in the
opening between the PSS-CD01
and PS-A units.
4) Connect the PSS-CD01 to the PS-A
unit via the connection cable.
•Be sure to confirm that
the Cable's #1 pin mark
comes to the #1 pin side
oftheIDEconnector.
Caution
Refer to the following drawings to confirm that the connection
cable is securely attached to both connectors. Be sure to check
both connectors before turning the PS-A ON, since incorrect
attachment of the connectors can cause equipment damage.
XX
!!
!!
!
#1 pin mark
CD-ROM Drive I/F
Cable's #1 pin mark

E-5
When using the CD-ROM drive unit with the PL-X920 Series unit, be sure to
change the "IDE Primary Master PIO" and "IDE Primary Slave PIO" settings
within the "System Information area INTEGRATED PERIPHERALS" to
"Mode 2". Also, be sure to set the "IDE Primary Master UDMA" and "IDE
Primary Slave UDMA" settings to "Disabled".
PL Series User Manual, Chapter 5 System Setup.
WARNINGS
Shock Danger! Be sure to unplug the PL unit from its power
supply prior to installing the PSS-CD01.
3Installation to PL


 PL-X920/X930 Series (4-slot type)
(PL-6930T)
(PL-6920T)
1) Unscrew the IDE cover's two (2) attach-
ment screws. Remove the IDE cover.
2) Unscrew the Expansion Slot 1 cover's
two (2) attachment screws. Remove the
the cover.
• IDE Cover for PL-X920 Series is as
shown left. Remove the IDE Cover as
same as PL-X930 Series.
•WhenthePSS-CD01unitisusedwithPL-X920Series,theSlaveHDD
cannotbeused.Besuretouninstall(remove)theSlaveHDDunit.
•ForPL-X930Series,ifyouwanttousetheHDD/CFcardunitinthe"Expan-
sionSlot1"togetherwiththeCD-ROMdriveunit,thesettingoftheHDD/CF
cardunitmustbe"Master"(asthefirstdisk). Todofailureso,itmaycause
malfunction.

E-6
Cable's red
line
3) Secure PL rear face fastener to the rear
of the PL unit using the two (2) attach-
ment screws. Fastening torque should
be 0.5 to 0.6N•m.
4) Secure PL front face fastener to the
bottom of the PSS-CD01 unit using the
two (2) attachment screws. Fastening
torque should be 0.5 to 0.6N•m.
• Insert firmly both sides of parts, which
are marked with thick circles (salients
and holes) .
5) Connect the CD unit to the PL unit via
the connection cable, folded the cable
over, along the diagonal line.
• Be sure to confirm that the
Cable's red line comes to
the PCI bus side of the IDE
connector.
Caution
Refer to the following drawings to confirm that the
connection cable is securely attached to both
connectors. Be sure to check both connectors before
turning the PL ON, since incorrect attachment of
the connectors can cause equipment damage.
XX
!!
!!
!
PCI bus side
of the IDE
connector

E-7
6) Secure the PSS-CD01 to the PL unit
using the four (4) attachment screws.
The torque should be 0.5 to 0.6N•m.
Place the cable in the opening between
the PSS-CD01 and PL units.
•When using the HDD/CF Card
unit within the Expansion Slot
1 for PL-X930 Series, Step 6) is
not required. PSS-CD01 should
be used, unattached on the rear
of PL unit.


 PL-X921/X931 Series (2-slot type)
1) Unscrew the IDE cover's two (2) attach-
ment screws. Remove the IDE cover.
2) Unscrew the Expansion Slot 1 cover's
two (2) attachment screws. Remove the
the cover.
3) Secure PL rear face fastener to the rear
of the PL unit using the two (2) attach-
ment screws. Fastening torque should
be 0.5 to 0.6N•m.
4) Secure PL front face fastener to the
bottom of the PSS-CD01 unit using the
two (2) attachment screws. Fastening
torque should be 0.5 to 0.6N•m.
• Insert firmly both sides of parts, which
are marked with thick circles (salients
and holes) .
(PL-6931 Series)

E-8
© 2003 Digital Electronics Corporation All rights reserved.
Note
Please be aware that Digital Electronics Corporation shall not be held liable
by the user for any damages, losses, or third party claims arising from the
uses of this product.
Digital Electronics Corporation
8-2-52 Nanko Higashi, Suminoe-ku, Osaka 559-0031, Japan
URL: http://www.pro-face.com/
5) Connect the CD unit to the PL unit via
the connection cable, folded the cable
over, along the diagonal line.
•Be sure to confirm that the
Cable's red line comes to
the PCI bus side of the IDE
connector.
Caution
Refer to the following drawings to confirm that the
connection cable is securely attached to both
connectors. Be sure to check both connectors before
turning the PL ON, since incorrect attachment of
the connectors can cause equipment damage.
XX
!!
!!
!
6) Secure the PSS-CD01 to the PL unit
using the four (4) attachment screws.
The torque should be 0.5 to 0.6N•m.
Place the cable in the opening between
the PSS-CD01 and PL units.
•When using the HDD/CF Card
unit within the Expansion Slot
1 for PL-X931 Series, Step 6) is
not required. PSS-CD01 should
be used, unattached on the rear
of PL unit.
Cable's red
line
PCI bus side
of the IDE
connector