manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. PROEL
  6. •
  7. Passive Loudspeaker
  8. •
  9. PROEL NEOS12PX User manual

PROEL NEOS12PX User manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

USER MANUAL
NEOS12PX
passive loudspeaker
KEY FEATURES
• Premium transducers
• Rotatable asymmetric HF horn
• HF driver protecon
• Plywood cabinets with die-cast handles, dual-angle pole holder and mulple flying points
INTRODUCTION
NEOS PX series represents the highest expression of PROEL GROUP Research & Development applied in loudspeaker systems. A natural evoluon
of the NEOS Series, it incorporates the latest technologies developed by PROEL in advanced sound reinforcement systems able to provide premium
sound, maximum performance and up-to-date features.
The NEOS PX are designed for the use both as high-performance mobile systems for live applicaons and for advanced fixed installaons.
The NEOS PX are able to provide an exceponal sound definion together with very high dynamics and low distoron in an ultra-compact
package.
The NEOS PX passive filters are provided with a protecon on circuit for the HF driver, which has a two-step operaon: the first step reduces the
power accordingly to the music content and without an audible effect; if a too high power level is present for a long period of me, the second
step shut the HF driver off.
TECHNICAL SPECIFICATION
AcousƟcal Frequency Response Diagram
System type Full range 2-way, vented
Low frequency driver 12’’ woofer - 2.5” VC
High frequency driver 1’’ compression driver - 1.75” VC
Frequency response 55 Hz - 20 kHz
Horn type Asymmetrical rotatable horn
Coverage 100°>80° H x 60° V
Max SPL 127 dB
Electrical
Nominal Impedance 8 ohm
Power Handling Connuous 350 W
Power Handling Peak 700 W
Sensivity 99 dBspl @ 1W / 1m
Passive Crossover Frequency 2000 Hz
Connectors IN - LINK: Speakon® (NL4MP)
Controls FULL-RANGE / BI-AMP operaon (internal jumper)
Mechanical
Construcon 15 and 18 mm birch plywood
Finish An-scratch black paint
Flying hardware 4 x M10 - top, boom, rear
Trapezoidal taper 10°
Monitor taper 42°
Pole holder 1 boom dual angle (0° / 7.5°)
Dimensions (W x H x D) 400 x 600 x 365 mm
Weight 22 kg (48.5 lbs)
10k5k2k
1k
500200100502020 20kHz
110.0
dBSPL
100.0
90.0
80.0
70.0
60.0
MECHANICAL DRAWING
41.0 cm
16.1"
36.0 cm
14.2"
61.0 cm
24.0"
Dual Angle Pole Holder
M10 Flying Point
M10 Flying Point
M10 Flying Point
OPTIONAL ACCESSORIES
ASO25 2 in 4 out analog loudspeaker processor for speaker suspending:
PC240 2 in 4 out digital loudspeaker processor PLH295 M10 Ø 50 mm Truss mount coupler
PC260 2 in 6 out digital loudspeaker processor AC169A M10 black shoulder eyebolt
COVERNE12 Loudspeaker sobag AC171 L = 75 cm / 30 inch Aircracable sling
FRE300BK Loudspeaker ground stand AC172 L = 1.5 m / 4.9 Aircracable sling
KP210BK Sub-Speaker pole AC173 Screw pin anchor shackle
KPPTL12 Loudspeaker wall stand
KPTFL12PB Loudspeaker free aiming ground stand
NL4FX Neutrik Speakon® PLUG
see www.proel.com for detailed descripon and other available accessories.
SPARE PARTS
NL4MP Neutrik Speakon® panel socket
91CR0063 Crossover module
98NEOS12WZ8 12’’ woofer - 2.5” VC
98DRI1475 1’’ compression driver - 1.75” VC
REAR PANEL
INPUT - External amplifier power input. The signal is filtered by a passive crossover. The connecons depend by the configuraon sengs
accordingly the following table:
INPUT
FULL RANGE BI-AMP
1+ / 1- INPUT 1+ / 1- LOW
2+ / 2- INTERNALLY N.C. 2+ / 2- HIGH
LINK - Power signal output, to connect the unit to another speaker. The INPUT and LINK connectors are parallel to each other.
PRODUCT LABEL - In this label are wrien the most important data informaon about the passive loudspeaker, model, impedance, maximum
applicable connuous power, serial number.
FULL RANGE / BI-AMP MODE - The speaker system can operate both in FULL RANGE and BI-AMP mode:
In FULL RANGE mode a built- in crossover filter allows the loudspeaker to be powered by a single amplifier.
The BI-AMP mode requires a dedicated amplifier for each speaker (woofer and HF driver), even if the internal crossover is not excluded we
recommend the use of an external crossover or processor before the amplifiers.
The mode selecon can be done by an internal jumper (see figure 1), which can be accessible by removing the rear connecon plate. The factory
seng is FULL-RANGE mode.
FIGURE 1: TO SET THE LOUDSPEAKER AS BI-AMP,
REMOVE THE REAR PANEL, LOCATE THE JUMPER AND
MOVE IT IN THE OTHER SIDE OF THE CROSSOVER
CIRCUIT.
LIMITED WARRANTY
Proel warrants all materials, workmanship and proper operaon of this product for a period of two years from the original date of purchase. If any defects are found
in the materials or workmanship or if the product fails to funcon properly during the applicable warranty period, the owner should inform about these defects the
dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed descripon. This warranty does not extend to damage resulng from
improper installaon, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and warranty is sll
valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defecveness.
• This unit package has been submied to ISTA 1A integrity tests. We suggest you control the unit condions immediately aer unpacking it.
• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspecon.
• Proel is not responsible for any damage that occurs during shipment.
• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
• Possible damages to unit should be immediately nofied to forwarder. Each complaint for package tampered with should be done within eight days from product
receipt.
SAFETY INSTRUCTIONS
– To reduce the risk, close supervision is necessary when the product is used near children.
– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.
– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.
– This product should be located so that its locaon or posion does not interfere with its proper venlaon and heang dissipaon.
– Care should be taken so that objects and liquids do not go inside the product.
– The product should be connected to a power supply mains line only of the type described on the operang instrucons or as marked on the product. Connect the
apparatus to a power supply using only power cord included making always sure it is in good condions.
– WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
– Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connecon.
– Make sure that power supply mains line has a proper earth connecon.
– Power supply cord should be unplugged from the outlet during strong thunderstorm or when leunused for a long period of me.
CE CONFORMITY
Proel products comply with direcve 2004/108/EC (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with direcve 2006/95/CE (LVD), as stated in EN
60065 standard.
PROEL S.p.A. (World Headquarter) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY
Tel: +39 0861 81241 Fax: +39 0861 887862 www.proel.com