Prospect Designs ALICIA PRONE STANDER User manual

INSTRUCTION MANUAL
ALICIA PRONE STANDER
Size Large—APS3
Read and follow all instructions for assembly and use before
using this product

Warnings
The use and adjust ent of this stander ust only be with the reco endation
and guidance of a qualified therapist or physician. Adult supervision is
required at all ti es. Never leave a child unattended while the product is in
use.
Prospect Designs, Inc will not be responsible for da age or injury resulting
fro any odification to this equip ent by anyone other than the
anufacturer.
Prospect Designs, Inc will not be responsible for da age or injury resulting
fro isuse or neglect of this equip ent.
USE
The Alicia Prone stander is designed to provide the child with ability to experience
weight bearing in an upright or forward leaning position while the combination of
adjustments and supports hold the child in good postural alignment.
Never leave a child unattended.
CARE
Regular inspections should be done to check for loose or missing hardware or any
signs of cracked or broken parts. Contact the manufacturer immediately if you
suspect an unsafe condition.
All components may be cleaned with a mild soapy water or non abrasive
commercial cleaner approved for use on vinyl and wood. Care should be taken to
not use excessive amounts of water and wood parts should be wiped dry after
cleaning.
WARRANTY
All Prospect Designs, Inc products are guaranteed to be free from defects in
materials and workmanship for the life of the product. Should any part break or fail
Prospect Designs, Inc. will repair or replace it at no charge to the original owner

FITTING AND ADJUSTING
THE
ALICIA PRONE STANDER
APS3
Height Adjust ent
The height of the Alicia
Prone Stander is
generally adjusted in
relation to the height of
the child’s mid chest
height. The top of the
chest pad should come up
to about in line with the
child’s armpit or axila .
Each child is different so
this and every adjustment
should be determined by
a therapist or physician.
To adjust the height of the
stander you need to
loosen the height
adjust ent knobs on
each side of the stander.
The whole upper portion
of the stander can then be
raised or lowered to the
appropriate height. Be
sure to re tighten the
knobs securely.
As the stander is raised or
lowered the height from
the foot platform to all
other components will
change also and may
need to be re adjusted.
Height
adjustment
knob
Stander at tallest height
Stander at lowest height

Angle Adjust ent
Angle
Adjustment
knobs
The angle of the prone
stander can be adjusted
from an upright, 90° position
to approximately 30° forward
tilt. To change the angle of
the stander loosen the two
angle adjustment knobs and
move the stander to the
desired angle. Be sure to re
tighten the knobs firmly.
Stander in the upright position
Stander with maximum forward tilt

Tray Adjust ent
Tray in lowest position
Tray in highest position
The tray is adjustable
for both height and
angle.
HEIGHT
ADJUSTMENT
Loosen the knobs on
each side of the
stander and raise or
lower the whole tray
assembly to the
desired height.
TRAY ANGLE
Loosen the knobs on
each side of the tray
assembly to change
the incline of the tray

INSTALLATION & SAFETY INSTRUCTIONS
FOR
BACK EXTENSION
The BKSE1 attaches to the Posterior Pelvic Support Gate using the two kno s (A) that are
taped to the extension in shipping. Remove the kno s and position the ack/headrest extension
so that the kno s can e inserted through the vertical slots on the extension. Adjust to desired
height and tighten the kno s.
When using the BKSE1 option the velcro strap (B) on the upper lateral supports should e
secured around the ack extension once the gate has een closed to give additional support to the
assem ly. It is not needed for upper trunk support since that function is taken over y the ack
extension.
B
A

INSTALLATION & SAFETY INSTRUCTIONS
FOR
BACK/HEADREST EXTENSION
The BKSE1 and BKSE2 attach to the Posterior Pelvic Support Gate using the two knobs (A)
that are taped to the extension in shipping. Remove the knobs and position the back/headrest
extension so that the knobs can be inserted through the vertical slots on the extension. Adjust to
desired height and tighten the knobs.
When using the BKSE1 or BKSE2 option the velcro strap (B) on the upper lateral supports
should be secured around the back extension once the gate has been closed to give additional
support to the assembly. It is not needed for upper trunk support since that function is taken over
by the back extension.
B
A
Stander pictured
with BKSE2-
back/headrest
extension