PSG CADDY ADVANCED WOOD Series User manual

45246A
Printed in Canada 19-08-2021
Installation and operating instructions
for the CADDY ADVANCED WOOD SERIES ADD-ON
(PF01020)
Certified according to CSA B415.1-10, CSA B366.1
Allowed only in Canada
Read these instructions carefully before installing
and operating your furnace.
CONGRATULATIONS!
You have purchased one of the finest wood furnace available on the
market. We are confident that your furnace will provide years of comfort
and safe operation.
Please keep this document!
Verified and tested for Canada by
an accredited laboratory.
This manual is available for free download on the
manufacturer’s web site. It is a copyrighted document. Re-
sale is strictly prohibited. The manufacturer may update this
manual from time to time and cannot be responsible for
problems, injuries, or damages arising out of the use of
information contained in any manual obtained from
unauthorized sources.
Eco-energy at the hearth
of your home
Caddy
250, de Copenhague,
St-Augustin-de-Desmaures
(Quebec)
CANADA G3A 2H3

2

3
TABLE OF CONTENT
1 INTRODUCTION........................................................................................................................................................5
2 FURNACE PERFORMANCE
(1)
.................................................................................................................................6
3 GENERAL FEATURES .............................................................................................................................................7
4 SPECIFICATIONS .....................................................................................................................................................8
5 LABELS.....................................................................................................................................................................9
6 TECHNICAL DATA OF THE CADDY ADVANCED ADD-ON SERIE ....................................................................11
7 CADDY ADVANCED ADD-ON DIMENSIONS .......................................................................................................11
8 CHIMNEY AND DRAFT ..........................................................................................................................................12
9 SAFETY RULES......................................................................................................................................................12
9.1 GENERAL REQUIREMENTS .......................................................................................................................................... 12
9.2 ODOUR FROM THE PAINT............................................................................................................................................. 13
9.3 ASH DISPOSAL............................................................................................................................................................... 13
9.4 CREOSOTE BUILD-UP AND REMOVAL......................................................................................................................... 13
9.5 SMOKE DETECTOR ....................................................................................................................................................... 13
9.6 DOOR GLASS ................................................................................................................................................................. 13
9.7 ASH DRAWER................................................................................................................................................................. 13
9.8 ASH GRATE .................................................................................................................................................................... 14
9.9 ADDITIONAL FRESH AIR SUPPLY................................................................................................................................. 14
10 FIREWOOD .............................................................................................................................................................15
10.1 TREE SPECIES............................................................................................................................................................... 15
10.2 LOG LENGTH.................................................................................................................................................................. 15
10.3 PIECE SIZE ..................................................................................................................................................................... 15
10.4 HOW TO DRY FIREWOOD? ........................................................................................................................................... 16
10.5 JUDGING FIREWOOD MOISTURE CONTENT .............................................................................................................. 16
CADDY ADVANCED SERIAL ADD-ON INSTALLATION PF01020...............................................................................17
11 SAFETY PRECAUTION ..........................................................................................................................................18
12 INTRODUCTION......................................................................................................................................................18
12.1 BLOWER OF THE EXISTING FURNACE ........................................................................................................................ 18
13 APPLIANCE INSTALLATION.................................................................................................................................18
13.1 MATCHING THE TRANSFER DUCT BETWEEN THE TWO HEAT GENERATORS ....................................................... 18
14 MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS ...............................................................................23
14.1 MINIMUM CLEARANCES TO COMBUSTIBLES MATERIALS FOR AIR RETURN DUCT............................................... 24
14.2 MINIMUM CLEARANCES TO COMBUSTIBLES MATERIALS FOR HOT AIR PLENUM ................................................. 24
14.3 FLOOR PROTECTION .................................................................................................................................................... 24
14.4 INSTALLING THE CONNECTING DUCT FROM THE EXISTING FURNACE.................................................................. 25
14.5 PIPE CONNECTOR......................................................................................................................................................... 25
14.6 ELECTRICAL CONNECTION SERIAL FURNACE .......................................................................................................... 25
14.7 THERMOSTAT INSTALLATION...................................................................................................................................... 25
14.8 RTD INSTALLATION ....................................................................................................................................................... 25
14.9 TOOL HOLDER INSTALLATION ..................................................................................................................................... 25
14.10 OPERATING INSTRUCTIONS ........................................................................................................................................ 25
14.11 INSTALLATION INSTRUCTIONS.................................................................................................................................... 26
14.12 HOT AIR PLENUM TEMPERATURE PROBE INSTALLATION AND CONNECTION (RTD)............................................ 26
14.13 UNIT LOCATION ............................................................................................................................................................. 28
14.14 THE STOVE PIPE............................................................................................................................................................ 28
14.15 ELECTRICAL CONNECTIONS ....................................................................................................................................... 30
14.16 DRAFT REQUIREMENTS ............................................................................................................................................... 30
14.17 FRESH AIR SUPPLY INSTALLATION............................................................................................................................. 31
14.18 TOOL HOLDER INSTALLATION ..................................................................................................................................... 32
14.19 HOT AIR PLENUM........................................................................................................................................................... 33
15 THERMOSTAT INSTALLATION.............................................................................................................................33
15.1 SERIAL ADD-ON ONLY................................................................................................................................................... 33
16 FURNACE OPERATION .........................................................................................................................................35
16.1 HOW IT WORKS?............................................................................................................................................................ 35
16.2 HOW RELOAD BUTTON WORKS?................................................................................................................................. 35
16.3 HOW TO LIGHT AND RELOAD THE FURNACE ............................................................................................................. 36
16.3.1 COLD START AND COAL EMBER BED (The led button light is OFF) .............................................................. 37
16.3.2 HOT EMBER BED RELOAD (The led button light is ON or slowly blinking)...................................................... 38
16.4 YOUR FIRST FIRES........................................................................................................................................................ 38
16.5 LIGHTING FIRES ............................................................................................................................................................ 38

4
16.5.1 CONVENTIONAL FIRE STARTING ..................................................................................................................... 39
16.5.2 THE TOP DOWN FIRE......................................................................................................................................... 39
16.5.3 TWO PARALLEL LOGS ........................................................................................................................................ 39
16.5.4 USING FIRE STARTERS....................................................................................................................................... 39
17 MAINTAINING WOOD FIRES.................................................................................................................................40
17.1 GENERAL ADVICE ......................................................................................................................................................... 40
17.1.1 RAKING CHARCOAL ........................................................................................................................................... 40
17.1.2 FIRING EACH NEW LOAD HOT ......................................................................................................................... 40
17.1.3 CONTROL OF THE AIR SUPPLY ........................................................................................................................ 41
17.1.4 BUILDING DIFFERENT FIRES FOR DIFFERENT NEEDS............................................................................... 41
17.1.5 SMALL FIRES TO TAKE THE CHILL OFF THE HOUSE................................................................................... 41
17.1.6 LONG LASTING LOW OUTPUT FIRES .............................................................................................................. 41
17.1.7 HIGH OUTPUT FIRES FOR COLD WEATHER.................................................................................................. 41
17.1.8 MAXIMUM BURN CYCLE TIMES ....................................................................................................................... 41
17.2 PROLONGED POWER OUTAGE.................................................................................................................................... 41
18 FURNACE MAINTENANCE....................................................................................................................................42
18.1 ASH REMOVAL ............................................................................................................................................................... 42
18.2 CLEANING DOOR GLASS .............................................................................................................................................. 43
18.3 DOOR ADJUSTMENT ..................................................................................................................................................... 43
18.4 REPLACEMENT OF THE GLASS AND GASKETS ......................................................................................................... 44
18.5 CLEANING AND PAINTING THE FURNACE .................................................................................................................. 45
18.6 HEAT EXCHANGERS CARE........................................................................................................................................... 46
18.7 THERMOCOUPLES CARE ............................................................................................................................................. 49
18.8 CHIMNEY MAINTENANCE ............................................................................................................................................. 50
18.9 FIREBRICKS INSPECTION............................................................................................................................................. 50
18.10 SMOKE PIPE INSPECTION ............................................................................................................................................ 50
18.11 INSTALLATION OF SECONDARY AIR TUBES AND BAFFLE ........................................................................................ 51
19 TROUBLESHOOTING ............................................................................................................................................52
20 EXPLODED DIAGRAM AND PARTS LIST ............................................................................................................53
21 ELECTRICAL DIAGRAM FOR STAND-ALONE FURNACE .................................................................................62
22 WHY PURCHASE THROUGH AN AUTHORIZED CADDY DEALER? .................................................................62
CADDY LIMITED LIFETIME WARRANTY (REGULAR).................................................................................................63
CADDY LIMITED LIFETIME WARRANTY (PRIVILEGE) ...............................................................................................64

5
IMPORTANT NOTE:
This furnace and its hot air duct system must be sold and installed by a professional. In the absence
of a professional installer, the manufacturer reserves the right not to apply its warranty or to refuse
any technical support.
REGISTER YOU WARRANTY ONLINE
To receive full warranty coverage, you will need to show evidence of the date you purchased
your furnace. Keep your sales invoice. We also recommend that you register your warranty
online at: https://www.caddyfurnaces.com/en/warranty/warranty-registration
Registering your warranty online will help us track rapidly the information we need on your
furnace.
1 INTRODUCTION
This furnace uses the Dual Fire© technology with a two-stage electronic combustion control. Find peace of mind with a
self-regulated combustion that allows easy ignition. Its automated air supply and self regulated systems synchronize with
your thermostat to offer additional safety, optimize comfort and reduce emissions with minimal maintenance. This model
meets the emissions limits of CSA B415.1-10 Standard and EPA 40CFR Part 60, subpart QQQQ (2020 limit).
To optimize the efficiency of your furnace, here is some advice that you should follow when installing or operating your
Caddy Advanced.
Respect the local codes (when in doubt, consult your local dealer).
Make sure your furnace is installed according to the instructions on the certification label.
All controls and adjustments must be performed by a qualified technician. The blower speed must conform to
the recommendations of local codes and should respect the static pressure ranges in the warm air plenum of
the furnace.
We recommend that our wood burning hearth products be installed and serviced by professionals who are certified in
the United States by NFI (National Fireplace Institute
®
) or in Canada by WETT (Wood Energy Technical Training) or in
Quebec by APC (Association des Professionnels du Chauffage).
This furnace has been developed and built for residential heat source. Commercial and industrial use is prohibited and
will void the warranty.

6
2 FURNACE PERFORMANCE
(1)
Fuel type Dry cordwood
Recommended heating area[*] 1,000 to 2,500 ft² (93 à 232 m²)
Firebox volume 3.6 ft³ (0.102 m³)
Maximum burn time[*] 10 h
Maximum input capacity (dry cordwood)
(2)
310,000 BTU
Overall heat output rate (min. to max.)
(3)
19,354 BTU/h to 47,052 BTU/h (5.6 kW to 13.8 kW)
Average overall efficiency
(8)
76.6% (HHV)
(5)
82.0% (LHV)
(6)
Delivered heat output rate (min. to max.)
(7)
13,297 BTU/h to 42,234 BTU/h (3.9 kW to 12.4 kW)
Average delivered efficiency
(4)
60.7% (HHV)
(5)
65.0% (LHV)
(6)
Optimum overall efficiency
(9)
83.2%
Optimum heat transfer efficiency
(14)
81%
Average particulate emissions rate
(10)(11)
0.095 lb/mmBTU (0.041 g/MJ)
Average CO
(12)
8.78 lb/mmBTU (3.78 g/MJ)
Average electrical power consumption
(13)
30 W
[*]
Recommended heating area and maximum burn time may vary subject to location in home, chimney draft, heat loss factors,
climate, fuel type and other variables. The recommended heating area for a given appliance is defined by the manufacturer as its
capacity to maintain a minimum acceptable temperature considering that the space configuration and the presence of heat
distribution systems have a significant impact in making heat circulation optimum.
(1)
Values are as measured per CSA B415.1-10, except for the recommended heating area, firebox volume, maximum burn time and
maximum input capacity. Performances based on a fuel load prescribed by the standard at 10 lb/ft³ and with moisture content
between 18% and 28%.
(2)
Input value at 10lb/ft³ fuel loading density and dry energy value of 8,600BTU/lb.
(3)
Overall: Radiated and delivered heat together at10lb/ft³ fuel loading density over one total burn cycle.
(4)
Efficiency based on delivered heat when allowing cycling from high to low burn to simulate thermostat demand.
(5)
Higher Heating Value of the fuel.
(6)
Lower Heating Value of the fuel.
(7)
Delivered: Remotely provided to other rooms through ducting at 10 lb/ft³ fuel loading density over one total burn cycle.
(8)
Efficiency based on radiated and delivered heat when allowing cycling from high to low burn to simulate thermostat demand.
(9)
Optimum overall efficiency at a specific burn rate (LHV).
(10)
Based on delivered heat output.
(11)
This appliance is officially tested and certified by an independent agency.
(12)
Carbon Monoxide. Based on overall heat output at 10lb/ft³ fuel loading density.
(13)
Unless stated otherwise, measures were taken directly at the main power source and include all electrical components present in
the appliance.
(14
)
The optimum heat transfer efficiency is for the low burn rate and represents the appliance’s ability to convert the energy
contained in the wood logs into energy transferred to the room in the form of heat and does not take into account the chemical
losses during combustion.

7
3 GENERAL FEATURES
Maximum log length 21 in (533 mm) / north-south**
Diameter of the flue collar 6 in (152 mm)
Recommended connector pipe diameter 6 in (152 mm)
Recommended chimney diameter 6 in (152 mm)
Required type of chimney CAN/ULC S629 (2100 °F)
Baffle material C-Cast or equivalent
Alcove installation Not approved
Mobile home installation
‡
Not approved
Appliance weight (without option) 635 (288 kg)
Shipping weight (without option) 705 lb (320 kg)
Filter - dimensions (Width x Depth x Height)
(included with optional blower assembly) 14 in x 25 in x 1 in (356 mm x 635 mm x 25 mm)
Filter - quantity 1
Particulate emission standard CSA B415.1-10
Canadian standard (safety) CSA B366.1
** East-west: through the door you see the longitudinal sides of the logs; north-south: through the door you see the tips of the logs.
‡
Mobile home (Canada): In Canada, a mobile home is a dwelling for which the manufacture and assembly of each component is
completed or substantially completed prior to being moved to a site for installation on a foundation and connection to service facilities
and which conforms to the CAN/CSA-Z240 MH standard.

8
4 SPECIFICATIONS
Color Grey and black
Thermostatic control Yes
Door type Single, glass with cast iron frame
Glass type Ceramic glass
Air return plenum - dimensions (Depth or Height) 15 3/4 in
Air return plenum - dimension (Width) 24 3/4 in
Hot air plenum - dimensions (Depth or Height) 28 5/8 in
Hot air plenum - dimension (Width) 24 1/2 in
Ash pan - dimensions (Width x Depth x Height) 13 5/8 in x 20 1/2 in x 4 in
Clearance - front 48 in
Clearance - back wall 24 in from the control board housing recommended service
clearance
Clearance - side wall 6 in
Clearance - side wall 24 in recommended service clearance
Clearances - ducts 6 in for the first 6 feet and 1 in after
Clearance - recommended for maintenance on left
side 24 in
Top cold air plenum option - material Galvanized steel
Top cold air plenum option - dimensions
(Width x Depth x Height) 24 7/8 in x 15 7/8 in x 10 3/4 in
Top cold air plenum option - smoke pipe diameter 6 in
Fresh air intake adapter option 5 in
Fresh air intake adapter - connection location Left or right
Tested and listed as per applicable standards By an accredited laboratory (CAN)
Warranty Limited lifetime

9
5 LABELS

10

11
6 TECHNICAL DATA OF THE CADDY ADVANCED ADD-ON SERIE
MODEL VARIABLE
TEMPERATURE STATIC PRESSURE
CADDY ADVANCED ADD-ON
(SERIAL INSTALLATION)
(°F) MIN. MAX.
H2O
55 0,2 0,5
7 CADDY ADVANCED ADD-ON DIMENSIONS

12
8 CHIMNEY AND DRAFT
This furnace must be connected to a chimney certified for use with wood burning heating appliances, a 6-inch diameter
chimney is recommended.
The unit is not to be connected to a chimney flue serving another appliance. If the chimney draft exceeds 0.06 IN.W.C.,
a barometric draft control should be installed on the smoke pipe. Never install a manual damper. The barometric control
must be adjusted so that the maximum draft measured at the furnace outlet does not exceed 0.06 IN.W.C. Excessive
draft can overheat the appliance and reduce burn time. Conversely, a lack of draft can lead to poor combustion and
smoke returns.
9 SAFETY RULES
WARNING! THE INFORMATION GIVEN ON THE CERTIFICATION LABEL AFFIXED TO THE APPLIANCE
ALWAYS OVERRIDES THE INFORMATION PUBLISHED, IN ANY OTHER MEDIA (OWNER’S MANUAL,
CATALOGUES, FLYERS, MAGAZINES OR WEB SITES).
9.1 GENERAL REQUIREMENTS
Make sure the chimney outlet and the pipes are clean and in good condition.
Do not use chemical products or liquids to light the fire.
Do not burn wood coated with paint, glue or chemical products.
Do not burn wastes or flammable liquids such as gasoline, naphtha, motor oil, or other unsuitable
matters.
Do not store wood in the vicinity of the furnace. Respect the required clearances between combustible
materials and the source of heat.
WARNING! THE ASH DRAWER AND EXCHANGERS ACCESS PANEL GET VERY HOT. DO NOT
MANIPULATE WITH BARE HANDS.
WARNING: This product can expose you to chemicals including carbon monoxide, which
is known to the State of California to cause cancer, birth defects or other reproductive
harm. For more information go to
www.P65warnings.ca.gov/

13
9.2 ODOUR FROM THE PAINT
It is normal that smoke and odours emanate from the unit when you first light it. It is recommended to burn it at high rate
and ventilate the building until the odours disappear. The smoke is not toxic. This should be done before the ducts
are connected to the furnace to prevent smoke dispersion in the house.
9.3 ASH DISPOSAL
Ashes must be placed in a metal container with a tight fitting lid. The container should be stored outdoor, well away from
combustible materials. This container should not contain any other type of waste. If the ashes are meant to be buried in
soil, wait until all embers have thoroughly cooled before burying.
9.4 CREOSOTE BUILD-UP AND REMOVAL
When wood is burned slowly, it produces tar and other organic vapours which, when combined with moisture, form
creosote. The creosote vapours condensate in a relatively cool chimney flue. As a result, creosote residues accumulate
inside the flue lining and the exchangers.
To minimize the frequency of the chimney cleaning, buy your firewood at least one year before using it. Store it in a dry
place in order to obtain the minimum moisture rate and optimize the efficiency. Do not store wood or combustible
materials within the installation minimum clearances or the space required to reload the appliance and remove ashes.
When ignited, creosote produces an extremely hot fire inside the chimney.
In the first year of use, inspect the chimney system at regular intervals to determine a cleaning cycle. Depending on the
type of wood used and its quality, a mid-season cleaning may be required. A yearly cleaning is mandatory. If a significant
layer of creosote has accumulated, it must be removed immediately to eliminate the risk of chimney fire.
Remember that a small, hot fire is preferable to a large smouldering one to prevent creosote build-ups within the system.
Prepare an emergency procedure in case of a chimney fire. It is recommended to clean the heat exchangers
thoroughly at the end of season in order to prevent corrosion.
9.5 SMOKE DETECTOR
We highly recommend the use of a smoke detector. It must be installed at least 15 feet (4,57 m) from the appliance in
order to prevent undue triggering of the detector when reloading.
9.6 DOOR GLASS
To maintain a clean and safe installation, do not build your fire too close to the glass or allow logs to lean on the
glass.
Do not operate your furnace at too low a setting. Keep the air inlet opened long enough during the fire start-up
to prevent the fire from smouldering, which could stain the glass.
An intense fire will help keep the glass clean. However, in the event that your glass gets stained, which should
not occur under normal operating conditions, you will have to clean it using a wet cloth and a fireplace glass
cleaner. Clean the glass ONLY when the unit has cooled down. Do not use abrasive cleaner.
WARNING! AVOID KNOCKING OR SCRATCHING THE GLASS. IT COULD CRACK OR BREAK.
Glass specifications:
Made of 5/32" (4 mm) thick ceramic glass.
Do not operate your wood furnace with a broken glass, as this could seriously damage your furnace.
You can purchase a replacement glass from your Caddy dealer.
9.7 ASH DRAWER
Your furnace is equipped with an ash drawer to collect ashes produced by the combustion of wood. This drawer must
not be left open during combustion as this may cause over firing and serious damages to the furnace. Moreover, the
additional air created could cause the dispersion of ashes in the ventilation system. The drawer must be cleaned
weekly. Use a vacuum cleaner to remove any ashes around the drawer in order to avoid the dispersion of ashes
in the ventilation system.
It is important that the door, the heat exchanger door and the ash drawer be kept closed while the
appliance is in use. Maintain all gaskets in good condition; in case of deterioration, contact your
dealer for a genuine replacement gasket.

14
9.8 ASH GRATE
You must replace the ash grate if it is damaged and a replacement may be obtained from your dealer.
9.9 ADDITIONAL FRESH AIR SUPPLY
When the furnace and the chimney are completely cold, it may be necessary to provide fresh air by opening a door or a
window for a few minutes while lighting the fire. Take note that a house constructed or renovated in order to be airtight
may lack the volume of fresh air necessary for the proper combustion of a solid-fuel heating appliance.
In such a case, when starting up the fire, do not operate appliances that evacuate air outside the house, such as:
Range hood
Bathroom fan
Air exchanger
Ventilated central vacuum system
Clothes dryer
Exhaust blowers that are in a fuel storage room should be installed so as not to create negative pressure in the room
where the solid fuel appliance is located.
A fresh air supply may be necessary to prevent solid fuel units from spilling smoke into the house. The indications used
to determine if an additional fresh air supply is necessary are not appropriate for all the situations. When in doubt, it is
recommended to install a fresh air supply.
A fresh air supply may be needed if:
Solid fuel units present anomalies, such as irregular draft, smoke return, bad combustion, and/or reversed draft
(whether there is combustion or not).
Existing solid fuel units such as a stove or fireplace release odours, heat badly, cause smoke returns, or reversed
draft (whether there is combustion or not).
The opening of a window, even slightly, in calm weather (windless), eliminates every problem mentioned above.
The house is equipped with a tight vapour barrier and adjusted windows, and/or is equipped with an interior air
mechanical evacuation device.
There is excessive condensation on the windows in winter.
The house is equipped with a ventilation system.
If, according to these symptoms or other similar ones, there is insufficient combustion air, it is necessary to ensure an
additional combustion air supply. See section 14.17 FRESH AIR SUPPLY INSTALLATION

15
10 FIREWOOD
What is good firewood?
Good firewood has been cut to the correct length for the furnace, split to a range of sizes and stacked in the open until
its moisture content is reduced to 15% to 20%.
10.1 TREE SPECIES
The tree species the firewood is produced from is less important than its moisture content. The main difference in
firewood from various tree species is the density of the wood. Hardwoods are denser than softwoods. People who live
in the coldest regions of North America usually have only spruce, birch and poplar, other low-density species to burn and
yet they can heat their homes successfully.
Homeowners with access to both hardwood and softwood fuel sometimes use both types for different purposes. For
example, softer woods make good fuel for relatively mild weather in spring and fall because they light quickly and produce
less heat Softwoods are not as dense as hardwoods, so a given volume of wood contains less energy. Using softwoods
avoids overheating the house, which can be a common problem with wood heating in moderate weather. Harder woods
are best for colder winter weather when more heat and longer burn cycles are desirable.
Note that hardwood trees like oak, maple, ash and beech are slower growing and longer lived than softer woods like
poplar and birch. That makes hardwood trees more valuable. The advice that only hardwoods are good to burn is
outdated. Old, leaky cast iron furnaces would not hold a fire overnight unless they were fed large pieces of hardwood.
That is no longer true. You can successfully heat your home by using the less desirable tree species and give the forest
a break at the same time.
10.2 LOG LENGTH
Logs should be cut about 1" (25 mm) shorter than the firebox so
they fit in easily. Pieces that are too long make loading the furnace
very difficult. The most common standard length of firewood is 16"
(406 mm).
The pieces should be a consistent length, with a maximum of 1" (25
mm) variation from piece to piece.
10.3 PIECE SIZE
Firewood dries more quickly when it is split. Large unsplit rounds can take years to dry enough to burn. Even when dried,
unsplit logs are difficult to ignite because they don’t have the sharp edges where the flames first catch. Logs as small as
3"(76 mm) should be split to encourage drying.
Wood should be split to a range of sizes, from about 3"to 6"(76 mm to 152 mm) in cross section. Having a range of
sizes makes starting and rekindling fires much easier. Often, the firewood purchased from commercial suppliers is not
split finely enough for convenient stoking. It is sometimes advisable to re-split the wood before stacking to dry.

16
10.4 HOW TO DRY FIREWOOD?
Firewood that is not dry enough to burn is the cause of most complaints about wood burning appliances. Continually
burning green or unseasoned wood produces more creosote and involves lack of heat and dirty glass door. See section
18 FURNACE MAINTENANCE for concerns about creosote.
Things to consider in estimating drying time:
Firewood takes a long time to dry.
Firewood dries mostly from the exposed ends. Long pieces of wood should be cut to “firewood” length if expected
to dry.
Firewood bought from a dealer is rarely dry enough to burn, so it is advisable to buy the wood in spring and dry
it yourself.
Drying happens faster in dry weather than in damp, maritime climates.
Drying happens faster in warm summer weather than in winter weather.
Small pieces dry more quickly than large pieces.
Split pieces dry more quickly than unsplit rounds.
Softwoods take less time to dry than hardwoods.
Softwoods like pine, spruce, and poplar/aspen can be dry enough to burn after being stacked in the open for
only the summer months.
Hardwoods like oak, maple and ash can take one, or even two years to dry fully, especially if the pieces are big.
Firewood dries more quickly when stacked in the open where it is exposed to sun and wind; it takes much longer
to dry when stacked in a woodshed.
Firewood that is ready to burn has a moisture content between 15 and 20% by weight and will allow your furnace
to produce its highest possible efficiency.
10.5 JUDGING FIREWOOD MOISTURE CONTENT
You can find out if some firewood is dry enough to burn by using these guidelines:
Utilisez l’indicateur d’humidité pour le bois de chauffage fournit avec votre appareil afin de valider que l’humidité
se situe entre 15% et 20%. Pour obtenir une valeur plus précise, tester le milieu d'un morceau de bois
fraîchement fendu.
Des fissures apparaissent à l’extrémité des bûches au fur et à mesure qu’elles sèchent.
En séchant au soleil, le bois passe d’une coloration blanche ou crémeuse à gris ou jaune.
Frappez deux morceaux de bois ensemble, le bois sec sonne creux et le bois humide sonne sourd.
Le bois sec est beaucoup plus léger que le bois humide.
Fendez un morceau de bois et si la face mise à jour semble chaude et sèche au toucher, il est assez sec pour
être brûlé; s’il est humide au toucher, il n’est pas prêt.
Brûlez un morceau de bois, le bois humide chuinte et grésille dans le feu, pas le bois sec.

17
INSTALLATION
AND OPERATION INSTRUCTIONS
CADDY ADVANCED SERIAL ADD-ON
INSTALLATION PF01020

18
11 SAFETY PRECAUTION
CAUTION! THE OPERATION OF A GAS FURNACE MUST BE VERIFIED FOR ACCEPTABLE OPERATION
BEFORE AND AFTER INSTALLATION OF THE CADDY ADVANCED ADD-ON APPLIANCE BY A GAS FITTER
WHO IS RECOGNIZED BY THE REGULATORY AUTHORITY.
CAUTION! DO NOT CONNECT TO ANY GAS FURNACE THAT HAS NOT BEEN CERTIFIED INITIALLY AS
COMPLYING WITH CGA STANDARD CAN/CGA-2.3 OR ITS PRECEDENTS.
12 INTRODUCTION
The wood burning Caddy Advanced Add-on furnace is approved for in-line connection to an existing oil furnace or any
gas or electric furnace with a maximum heating capacity of 120,000 BTU/h. (35.17 kW).
Option PA08523 is required for serial add-on installation. Consult the sheet provided for this
purpose.
12.1 BLOWER OF THE EXISTING FURNACE
The theoretical air flow in the hot air plenum blower of the existing furnace must be at least 875 CFM when the external
static pressure is adjusted to 0,2" and to 0,5" of water column.
Some adjustment on the motor and blower of the existing furnace may be necessary. In this case, the following rules
apply:
On a belt-driven system, blower pulleys and motor pulleys may be changed to do the adjustment.
On a direct-drive system, the motor shall not be changed; however, the speed of the motor may be increased or
decreased.
CAUTION! THE BLOWER OF THE EXISTING FURNACE ITSELF SHALL NOT BE CHANGED.
WARNING! THE ELECTRICAL CURRENT FLOWING THROUGH THE BLOWER MOTOR SHALL NOT EXCEED THE
NAME PLATE RATING.
13 APPLIANCE INSTALLATION
If the existing furnace must be modified, the following standards must be respected:
Wood-oil: CSA B.139: Installation code for oil-burning equipment.
Wood-gas: CAN/CGA-B149.1 & CAN/CGA-B149.2: Natural Gas & Propane Installation Code et Propane Storage &
Handling Code.
13.1 MATCHING THE TRANSFER DUCT BETWEEN THE TWO HEAT GENERATORS
This furnace is certified only for installation in configuration presented in OPTION 1, 2, 3 and 4 of this section.
Configurations presented in Examples 1 and 2 of this section are prohibited.
Install the plenum and heating ducts in line as in OPTION 1 of this section. Series connection (OPTION 2)should be
considered ONLY if in line connection (OPTION 1) is not possible.
If the ducts are installed in series (OPTION 2) and the existing furnace’s fan limit control is mounted on the plenum, the
divider in the plenum must be installed at least 5" (127 mm) above the fan limit control. This divider must be air tight.
OPTION 3 & OPTION 4 are permitted when installing the Caddy Advanced furnace with an existing furnace whose hot
air plenum ducts are downwards flowing. The hot air plenum of the Caddy Advanced furnace must be above the furnace
and cannot be directed downward.
Do not install connecting ducts in a way that would allow inversion of the air flow (see example 1 and 3).
The transfer duct between the existing furnace and the add-on must be at least 190 square inches (0.12 m
2
) and
deviations radius must be at least 6" (152 mm). (See OPTION 1 & 2).

19
Option 1
Option
2
*Minimum duct size 190
square inches (0.12 m
2
)
*R = Minimum radius 6 inches

20
Option 3
Option 4