PSG PSG-2000 User manual

Stove Builder International Inc.
1700, Léon-Harmel
Québec(Québec)
G1N 4R9
Installation and Operating
Instructions for Wood and
Combined Furnaces
THIS MANUAL CONCERNS THE FOLLOWING FURNACES
WOOD
PSG-2000
PSG-3000
PSG-4000
PSG-4500
PSG-5000
COMBINED FURNACES
15, 18 or 20 KW and UH2000
15, 18, 20 or 25KW and UH3000
18, 20, 25 or 30KW and UH4000
18, 20, 25 or 30 KW and UH4500
40, 50 or 60 KW
All the instructions must be read carefully
before installing and operating furnace.
CONGRATULATIONS!
You have just purchased one of the best wood or combined
furnace on the market.
We are convinced that your furnace will provide you
with many years of comfort, safely.
Keep these instructions!
45216

2
TABLE OF CONTENTS
SECTION A : WOOD OR WOOD ELECTRIC FURNACES ...................................................4
INTRODUCTION..........................................................................................................................................4
1. CHIMNEY AND DRAFT..........................................................................................................................4
2. SAFETY RULES.......................................................................................................................................4
GENERAL REQUIREMENTS ....................................................................................................................4
ODOUR FROM THE PAINT......................................................................................................................5
ASH DISPOSAL..........................................................................................................................................5
CREOSOTE BUILD-UP AND REMOVAL.................................................................................................5
SMOKE DETECTOR..................................................................................................................................6
ASH DRAWER............................................................................................................................................6
ASH GRATE................................................................................................................................................6
3. APPLIANCE INSTALLATION.................................................................................................................6
UNIT LOCATION.......................................................................................................................................6
CLEARANCES TO COMBUSTIBLE MATERIALS....................................................................................7
PIPE CONNECTOR AND DAMPER.........................................................................................................7
DAMPER ....................................................................................................................................................8
COMBUSTION AIR....................................................................................................................................8
ELECTRICAL CONNECTION...................................................................................................................9
ELECTRIC ELEMENT.............................................................................................................................10
THERMOSTAT.........................................................................................................................................11
FAN CONTROL........................................................................................................................................12
4. OPERATING INSTRUCTIONS..............................................................................................................12
Control system..........................................................................................................................................12
HEATING .................................................................................................................................................13
EARLY SIGNS OF OVERFIRED FURNACE...........................................................................................13
WOOD AS HEATING FUEL....................................................................................................................13
CHIMNEY FIRES.....................................................................................................................................14
5. MAINTENANCE.....................................................................................................................................14
MAINTENANCE OF THE EXCHANGERS..............................................................................................14
MAINTENANCE OF THE BLOWER MOTOR.........................................................................................15
FILTERS...................................................................................................................................................15
DOOR GASKET MAINTENANCE ...........................................................................................................15
6. REPLACEMENT PARTS........................................................................................................................15
7. ELECTRIC DIAGRAMS FOR UNITS BUILT FROM 2005...................................................................16
WOOD-ONLY FURNACES......................................................................................................................16
PSG 5000 WOOD-ONLY FURNACES.....................................................................................................17
9. TECHNICAL SPECIFICATIONS ...........................................................................................................18
10. SELECTION CRITERIA (COMBINED WOOD/ELECTRIC FURNACE)..........................................19
11. TROUBLESHOOTING..........................................................................................................................20
12. DUCTS AND REGISTER MEASUREMENTS.....................................................................................21
SECTION B : WOOD/OIL COMBINED FURNACES.............................................................22
GENERAL NOTES......................................................................................................................................23
1. DRAFT AND CHIMNEY.........................................................................................................................23
2. OIL TANK AND PIPING.........................................................................................................................23

3
BURNER PUMP.......................................................................................................................................24
3. APPLIANCE INSTALLATION...............................................................................................................24
LOCATING THE UNIT ............................................................................................................................24
CLEARANCES TO COMBUSTIBLE MATERIALS..................................................................................24
POSITIONING THE APPLIANCE...........................................................................................................26
PIPE CONNECTOR AND DAMPER.......................................................................................................26
COMBUSTION AIR..................................................................................................................................29
ELECTRIC COMPONENTS INSTALLATION.........................................................................................30
ELECTRICAL WIRING............................................................................................................................31
THERMOSTAT.........................................................................................................................................31
FAN CONTROL........................................................................................................................................31
COMBUSTION SAFETY CONTROL.......................................................................................................32
COMBUSTION ADJUSTMENT AND VERIFICATION ..........................................................................33
ELECTRODES SETTING.........................................................................................................................34
4- APPLIANCE START-UP ........................................................................................................................35
5- PROLONGED CLOSING........................................................................................................................35
7- ELECTRICAL DIAGRAMS....................................................................................................................37
8- TECHNICAL DATA................................................................................................................................39
PSG LIMITED LIFETIME WARRANTY...................................................................................................40
REGISTER YOU WARRANTY ONLINE
To receive full warranty coverage, you will need to
show evidence of the date you purchased your
furnace. Keep your sales invoice. We also
recommend that you register your warranty online
at
www.psg-distribution.com
Registering your warranty online will help us track
rapidly the information we need on your furnace.

4
SECTION A : wood or wood electric furnaces
INTRODUCTION.
To get maximum performance from your PSG furnace, keep in mind the following:
•Comply with local codes (if in doubt, contact your local heating specialist).
•Make sure your furnace is installed according to the instructions on the certification plate.
•Make sure that your furnace has been installed in accordance with the required standards specified on the
furnace’s certification labels.
1. CHIMNEY AND DRAFT
This furnace must be connected to a chimney approved for wood-burning appliances; the chimney connector for a
PSG 2000 must have 6" diameter; 7” for PSG3000 and PSG4000, for all other models, use an 8" diameter chimney
connector.
Use of a barometric draft control is recommended in order to regulate the draft to the recommended setting.
Never use a manual chimney damper.
The barometric control must be adjusted so that the maximum draft measured at the furnace outlet does not exceed
-0.06 in. w.c. Please note that a draft exceeding -0.06 in. w.c. could produce an uncontrollable fire. On the other
hand, the minimum draft required is -0.04 in. w.c. in the evacuation pipe on the wood side, no matter what type of
furnace (PSG Wood, PSG Wood/Electric and PSG Wood/Oil).
2. SAFETY RULES
GENERAL REQUIREMENTS
•Never light your furnace using chemicals or other liquid fuels. Never installed automatic feeder on that unit.
•Do not burn wood coated with paint, glue or chemical products.
•Never store wood near the furnace. Respect the required minimum clearances between combustibles and
your furnace.
•Keep your furnace, chimney and smoke pipe connector clean and in good working order at all times. We
recommend that you establish clear procedures for wood storage, system maintenance and operation of
your furnace. Check creosote accumulation daily until you can determine by experience how often to clean.
Weekly cleanings may be necessary in mild weather, while a monthly cleaning may be all that is required
during the colder months of the year.
•Keep loading and ash drawer doors shut during operation and make sure their gaskets are in good
condition. To get a replacement gasket, contact your PSG dealer.
•A plentiful supply of combustion air and a vigorous fire will help prevent creosote accumulation.
All controls adjustments must be performed by a qualified technician. The controls settings and the blower speed must
conform to the recommendations of the National Warm Air Heating and Air Conditioning Association and respect the
recommended static pressure ranges in the warm air bonnet of the furnace (see General Technical data static
pressure).

5
ODOUR FROM THE PAINT
It is normal that a smoke odour emanate from the unit when you first light it. It is recommended to burn it at high
rate and ventilate the building until the odour resorbs.
ASH DISPOSAL
Ashes must be placed in a metal container with a tight fitting lid. The container should be placed outside, well away
from combustible materials. If the ashes are meant to be buried in soil, you should wait until all cinders have
thoroughly cooled.
CREOSOTE BUILD-UP AND REMOVAL
When wood is burned slowly, it produces tar and other organic vapours which, when combined with moisture, form
creosote. The creosote vapours condensate in a relatively cold chimney flue. As a result, creosote residues
accumulate in the flue lining.
N.B.: To minimize the frequency of chimney cleaning, buy your firewood at least one year before using it. Store it in a
dry place in order to obtain the minimum moisture rate and optimize the efficiency. Do not store wood or combustible
materials within the installation minimum clearances or the space required to reload the appliance and remove the
ashes.
When ignited, creosote produces an extremely hot fire inside the chimney.
To avoid this situation, it is important to do the turnover of wood. Inspect the chimney system at regular intervals to
determine a cleaning cycle. A weekly cleaning might be required during mild temperature periods but a monthly
cleaning should be sufficient during cold periods. If a significant layer of creosote has accumulated, it must be
removed immediately to eliminate the risk of a chimney fire.
Remember that a small hot fire is preferable to a large smouldering one to prevent creosote build-up within the
system. An emergency plan is necessary in case of a chimney fire.
It’s recommended to clean the heat exchangers thoroughly at the end of the season in order to help prevent
corrosion.
W A R N I N G
THE ASH DRAWER GET VERY HOT.
DO NOT MANIPULATE WITH BARE HANDS.

6
SMOKE DETECTOR
We highly recommend the use of a smoke detector. It must be installed at least 15 feet (4,57 m) from the appliance
in order to prevent undue triggering of the detector when reloading.
ASH DRAWER
Your appliance is equipped with an ash drawer to collect ashes produced by the combustion of wood. This drawer
must not be left open during combustion as this will cause over firing and serious damage to the furnace.
The drawer must be cleaned regularly.
ASH GRATE
You must replace the ash grate if it is damaged and a replacement may be obtained from your dealer.
3. APPLIANCE INSTALLATION
UNIT LOCATION
The furnace must be installed where outside air supply is sufficient for proper combustion. In airtight houses, it
might be necessary to install an outside air inlet (see details in: «3- INSTALLATION» COMBUSTION AIR).
The furnace must be positioned so that the connector is as short as possible in order to minimize the use of 90o
elbows.
The owner must ensure a proper installation to allow a safe operation of the appliance.
It is important that the door and the ash drawer be kept closed while the appliance is in use.
Maintain all gaskets in good condition: in case of deterioration, contact your dealer for
replacement.

7
CLEARANCES TO COMBUSTIBLE MATERIALS
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS FOR PSG FURNACES
N.B. THE AIR RETURN CONDUITS SHOULD BE AT LEAST EQUAL TO THE COLD AIR
PLENUM DIMENSIONS.
PIPE CONNECTOR AND DAMPER
A 6” diameter chimney listed for use with wood burning heating appliances is recommended for the PSG2000, 7” for
PSG3000-4000 and 8” for the others models. If draft exceed -0.06 w.c., you must install a barometric control(see
Damper). Never install a manual damper.
N.B. This appliance must be installed in accordance with the instructions on the unit’s certification.
Before proceeding to connection, remove all accessories such as:
scraper, shovel and poker from the evacuation pipe of the furnace.
OIL FLUE
PIPE
(OPTION)
MAIN
COLLECTO
R
24” both sides for
PSG5000
2”
WOOD
FLUE
PIPE

8
For a proper installation, follow the advices below:
1. All the joints of the evacuation pipe must be secured, using three screws.
Make sure that each screw goes through the inner walls of both connectors (male and female). See
pictures below showing a male-female coupling.
2. A minimum rise of 1/4 inch per horizontal foot must be respected.
DAMPER
The barometric control must be adjusted so that the maximum draft measured at the furnace outlet is limited to -0.06
in. w.c. Please note that a draft higher than -0.06 in. H2O could result in an uncontrollable fire. On the other hand,
the minimum draft to be respected is -0.04 in. w.c. in the evacuation pipe on the solid fuel side, no matter what
type of furnace.
COMBUSTION AIR
In the event that the furnace and the chimney are completely cold, it might be necessary before lighting, to provide
fresh air by opening a door or a window for a few minutes.
Take note that a house constructed or renovated in order to be airtight is liable to lack fresh air which is necessary
for a proper combustion and a proper operation of heating units.
In such a case, when starting up the fire, do not operate appliances which evacuate air outside the house such as:
- Range hood
- Air exchanger
- Cloths dryer
- Bathroom fan
- Ventilated central vacuum system
PROPER INSTALLATION UNPROPER INSTALLATION
CAUSE RESTRICTION

9
NOTE:
It is recommended to install an outside air inlet of minimum 4” diameter in the room where the heating appliance is
installed (see drawing below). To do so, it is preferable to choose a wall which is not exposed to extreme winds,
according to the conditions surrounding your house.
N.B. The owner of the furnace is responsible for the room salubrity in case of negative pressure or temporary
negative pressure.
ELECTRICAL CONNECTION
The following instructions do not supersede the local code.
WOOD ONLY
Install the fan limit control on the support provided after securing this support on the left edge of the hot air plenum
where two holes are pre-drilled (there are four pre-drilled holes on the edge of the PSG3000, use the two that are
located farther back). Install the servo-motor on the facade above the door, on the right side (use pre-drilled holes).
The chain that links the air inlet latch to the motor must have a play of 1/8 in. When there is no call for heat, the air
inlet latch must be completely shut and the chain must be affixed to the servo-motor at “8 o’clock”. *
The red switch located on the junction box controls low speed operation of the blower, in either ON (continuous
operation) or OFF modes.
WARNING: USE FEEDING WIRES SUITABLE FOR 75OC
WOOD/ELECTRIC
The high limit control on the electric unit is a manual reset thermostatic captor that is located directly inside the
electric unit (see INSIDE VIEW OF THE ELECTRIC ELEMENT). The electric elements must be installed as shown on
the diagram. Install the wood combined fan limit control on the support provided, at the determined location. The
connections must conform to the diagram.
Install the servo-motor on the facade above the door, on the right side (use pre-drilled holes). The chain that links
the air inlet latch to the motor must have a play of 1/8 in. When there is no call for heat, the air inlet latch must be
completely shut and the chain must be affixed to the servo-motor at “8 o’clock”. *
WARNING: USE FEEDING WIRES SUITABLE FOR 75OC
* (With all reserves on the minimum combustion air to be increased depending on the type and quality of the
combustible).
Insulated conduit full lenght
Fresh air
intake
Exterior
w
all
Free air
entr
y

10
ELECTRIC ELEMENT
The WOOD / ELECTRIC combined model uses two separate thermostats: one thermostat controls the electric
heating, the other one controls the wood heating. With this system, the electric heating has priority over the wood
heating. When the thermostat activates the electric heating, the air inlet closes down (if opened), the blower starts and
the electric elements are successively activated per block of 5 kW. The system may be connected to an outdoor
sensor which will allow the last block of elements (5 kW) to start up only when the outside temperature is cold enough.
This will reduce the power of the systems by 5 kW during mild temperature for more economy and comfort.
When the call for electric heat is completed, the wood system will take over if the setting of the wood thermostat is
higher than that of the electric thermostat.
So, in normal bi-energy use, you should set the wood system thermostat 2oto 3o higher than the electric system
thermostat.
Take note furnaces equipped with the G10 blower have a four speed motor and furnaces equipped with the G-12
have 2 speed motot and an adjustable pulley.
If the temperature of the element exceeds the limit allowed, the thermostatic captor will disengage the elements. To
reactivate, press the red “manual reset” button on the L-170 thermodisk; find out why the temperature limit has been
exceeded (static pressure too high, fan breakage, dirty filter, etc.) before reactivating.
SERVOMOTO
R
HOLES FOR FAN
LIMIT CONTROL

11
THERMOSTAT
The thermostat must be installed on an inside wall in a location where it is not likely to be affected by the draft
coming from an air outlet. It must be installed at a minimum of 55 inches above the floor.
N.B. The combined wood / electric model uses two thermostats and they should be installed at same height.
INSIDE VIEW OF THE ELECTRIC ELEMENT
OUTSIDE VIEW OF THE ELECTRIC ELEMENT
Thermodisk L-170
Red button
manual reset

12
FAN CONTROL
The fan control setting may vary depending on the type of installation. The “out of service” temperature is factory
set at 110oF and the “in service” temperature is factory set at 150oF. These settings should provide a proper operation
for most installations.
It is preferable for a prolonged operation of the blower that the setting “out of service” be low enough. But a setting
“out of service” too low will cause cold air circulation. To modify the settings, move the tabs at the desired position on
the temperature scale.
The adjustment of all controls must be performed by a qualified technician. The controls setting and the blower
speed must conform to the recommendations of the “Warm Air Heating and Air Conditioning National Association”.
The red switch located on the electric unit controls the low speed (summer speed) either at the “on” or the “off”
position. For a better efficiency, we recommend to let the blower be controlled automatically when heating with wood.
4. OPERATING INSTRUCTIONS
Control system
On the wood furnaces only, the thermostat controls the air inlet damper. When the thermostat calls for heat, the
damper opens and the fire burns up. When the furnace gets hot enough, the combined limit control activates the
blower motor at the speed selected for wood heating.
The chain that links the air inlet damper to the motor must have a play of 1/8 inch. When there is no call for heat,
the air inlet damper must be completely closed and the chain must be affixed to the servo-motor at “8 o’clock”. *
*(With all reserve on the minimum air to be increased depending on the type and quality of the combustible).
LIGHTING:
1. Open the door
Note: If there is already a bed of coals in the combustion chamber, go directly to PREHEATING.
2. Drop the ashes into the ash pan
3. Place one or two dry kindlings at the front of the combustion chamber
4. Place newspaper strips on top of the kindlings.
5. Cover the newspaper with more kindlings and small pieces of dry wood.
6. Add newspaper strips, then light the fire a low as possible and leave the door 1/2" (13 mm) opened. If you fail
lighting the fire, you might experience a back draft through the air inlets.
PREHEATING
1. Once the kindling is well ignited or the coals revived, put 2 or 3 fire logs in such a way that the flames can interlace
between the logs then close the door. It is important to respect these loading sequences so that the wood will burn
from the front to the back of the furnace.
2. Wait 15 to 20 minutes, then proceed with loading the furnace.

13
HEATING
1. When loading the furnace, lower the kindled pieces of wood and place them at the center of the combustion
chamber before adding new logs.
2. Do not overload. Air must circulate freely in the upper part of the furnace in order to obtain an efficient operation of
the appliance. Please note that a small hot fire will produce much less residues than a large smouldering one.
IMPORTANT: DURING THE HEATING PROCESS, REMOVE THE ASHES AND EMBERS THAT COULD
OBSTRUCT THE AIR INTAKE LOCATED BELOW THE DOOR INSIDE THE FURNACE.
EARLY SIGNS OF OVERFIRED FURNACE
1. Roaring fire.
2. Chimney connector is glowing red.
3. Extreme heat coming from the furnace. If this occurs, DO NOT OPEN THE DOOR, shut-off the air inlet opening
completely, and wait until the glow has completely subsided.
WOOD AS HEATING FUEL
We recommend that you burn dry wood only.
There are two important factors to be considered when choosing a type of wood: the moisture content and the wood
density. Hardwood, such as maple, oak and beech will provide better results because of the high density and minimal
tar produced during combustion. It is highly recommended to use wood that has been dried at least six months. Do
not use coal as heating fuel in this appliance.
Whenever a high amount of smoke is noticed in the room, you must:
1. Open doors and windows.
2. Make sure the furnace door is closed as well as the damper (if necessary, lower the thermostat starting point or
undo the chain of the damper and close manually the barometric draft control).
3. When the furnace has cooled down, inspect the chimney to detect obstructions and consult a specialist to
determine the cause of the smoke spillage.
CARBON MONOXYDE IS A LETHAL GAS (ODOURLESS AND COLOURLESS), WHICH YOU MUST
BEWARE OF.
PROCEDURE TO OPEN THE LOADING DOOR
TO MINIMIZE THE RISK OF A BACK DRAUGHT OPEN THE DOOR 1” AND WAIT ABOUT 10
SECONDS BEFORE OPENING COMPLETELY. THE PURPOSE IS TO STABILIZE THE
PRESSURE INSIDE THE FURNACE.
ALWAYS KEEP THE DOOR AND THE ASH DRAWER CLOSED
(except for lighting and maintenance).

14
CHIMNEY FIRES
Chimney fires might occur when the fire gets extremely hot. Burning cardboard, branches or pieces of wood can
ignite the creosote residue accumulated in the evacuation flue system. The usual signs are:
1. Rumbling
2. The flue gets extremely hot
3. Flames are coming out of the chimney
In case of a chimney fire, first call your local fire department and sprinkle the roof around
the chimney with water.
Make sure that the furnace door is closed as well as the damper (if necessary, lower the thermostat starting point or
release the chain from the damper and CLOSE the barometric draft control manually).
If the fire gets uncontrollable due to an improper use or because the draft is too strong, follow the same procedure
as in a chimney fire except that you will have to OPEN manually the barometric draft control.
LOCAL FIRE DEPARTMENT.
Phone number: ___________________________________
5. MAINTENANCE
MAINTENANCE OF THE EXCHANGERS
The evacuation pipe and the heat exchangers should be inspected regularly during the burning season. Using the
scraper, clean the exchanger pipes thoroughly on a regular basis.
INSTRUCTIONS
1oWait until fire is completely out before cleaning.
2oRemove the smoke pipe connector from the furnace.
3oInspect the furnace’s heat exchangers (rectangular tubes) through the smoke outlet for creosote accumulation. On
the PSG5000, you can access the heat exchangers by removing the square panel located at the back of the furnace.
4oUsing the supplied scraper, clean the heat exchangers and the combustion chamber and remove creosote residues.
5oReassemble the smoke pipe connector or access panels.
CHIMNEY MAINTENANCE
One of the most efficient methods is to sweep the chimney, using a hard brush. Brush up and down. Soot and
creosote residue will come off the inside surface and fall at the bottom of the chimney where it can be removed easily.
The chimney must be checked regularly and if creosote has accumulated, it must be removed. Cleaning on a
monthly basis should be sufficient during the coldest months.

15
Smoke flue inspection
- The smoke flue should be inspected regularly during the heating season.
- If possible, the smoke flue should be dismantled and cleaned.
- The flue should be inspected to detect any defect.
- If no defect is noticed, put the flue back in place; otherwise, it must be replaced.
- Use only wood as a combustible.
- Seasoned hard wood logs 18” to 22” long are recommended as a combustible.
Regular maintenance is required for safe and efficient operation of a controlled-combustion heating system. Chimney,
gaskets and smoke pipes must remain in good working condition.
MAINTENANCE OF THE BLOWER MOTOR
The two bearings of the motor must be lubricated once a year using non detergent SAE 20 oil.
FILTERS
The furnace must not be operated without the filters. The air filters must be cleaned or replaced regularly. Use the
same size and preferably the same type as the original filters.
DOOR GASKET MAINTENANCE
It is important to maintain the door gasket in good condition. After a while, the gasket might sag and a door
adjustment may be required to prevent air leakage; if adjustment is not sufficient, replace the gasket.
We recommend to replace the gasket that seals the door once a year in order to maintain a good control of the
combustion for maximum efficiency and security. To replace your door gasket, remove the old gasket and glue. Clean
the surface thoroughly, apply the gasket glue and put the new gasket onto the door. Wait for at least 2 hours before
lighting your furnace.
6. REPLACEMENT PARTS
Your PSG furnace is designed to burn clean and requires minimal maintenance. It’s recommended to conduct a visual
inspection at least once a month to uncover any damage to the unit. Any damage must be repaired as soon as
possible using genuine PSG replacement parts. You can find a complete list of replacement parts on our website at
www.psg-distribution.com.
DO NOT OVERLUBRICATE

16
7. ELECTRIC DIAGRAMS FOR UNITS BUILT FROM 2005
WOOD-ONLY FURNACES
FAN LIMIT HONEYWELL L6064(MOTOR (G-10) 4 SPEED AND (G-12) 2 SPEED)
RED
ON 150°F
LIMIT 250°F
OFF 110°F
LIMIT
LOAD
FAN
LINE
HONEYWELL
L6064
HIGH LINELOW
BLOWER
L2
HIGH
MED HIGH
MED LOW
LOW
TERMINAL
120 V.A.C.
COMMON
L1
BLUE
BLACK TRANSFO
JUNCTION BOX
24 V.A.C.24 V.A.C.
THERMOSTAT SERVO-MOTOR
BLACK
WHITE
OFF
ON 1
2
24 V.A.C.
120 V.A.C.
TRANSFORMER
SUMMER SWITCH
3
RED
WHITE
BLACK
BLACK
BLUE
BLACK
WHITE
4 SPEED MOTOR
DIRECT-DRIVE OR
2 SPEED MOTOR
G-12 BELT-DRIVE
REVISION JULY 6TH 2006

17
PSG 5000 WOOD-ONLY FURNACES
RED - HIGH SPEED
BLACK - LOW SPEED
WHITE - COMMON
FAN
2
3
1
JUNCTION BOX
THERMOSTAT 24 V.A.C.24 V.A.C. SERVO-MOTOR
1
2
3
FAN
RED - HIGH SPEED
BLACK - LOW SPEED
WHITE - COMMON
ON 150°F
OFF 110°F
LIMIT 250°F
LIMITFAN
HONEYWELL
L6064
LOADLINE LINE
FAN
LOAD
HONEYWELL
L6064
LIMIT
HIGHLOW LINE
RED
BLACK
LINELOW HIGH
WHITE
BLACK
RED
BLACK
TRANSFORMER
120 V.A.C.
24 V.A.C.
WHITE
2 SPEED
MOTOR
120 V.A.C.
L1 - BLACK
2 SPEED
MOTOR
BLOWER
L2 - WHITE
REVISION JANUARY 16th 2008

18
9. TECHNICAL SPECIFICATIONS
2000 3000 4000 4500 5000
A 45 ¼" 47" 50" 52 ½" 54 ½"
B 23 ½" 25 ½" 29 ½" 33 ½" 54"
C 45 ½" 47 ¼" 48" 48" 56 ¾"
D 15 ⅞" 15 ⅞" 19" 19" 19 ¾"
E 26 ⅜" 28" 28" 30" 31 ½"
F 22 ½" 24 ½" 28 ½" 32 ½" 51 ⅛"
G 40 ½" 41 ¼" 42" 42" 49 ½"
PIPES 7" 8" 8" 8" 8"
WEIGHT 445 540 600 660 1200
GENERAL TECHNICAL DATA
MODEL BELT DRIVE DIRECT DRIVE
FAN MOTOR SPEED FAN MOTOR SPEED OUTPUT
(C.F.M.)
TEMP
VAR.
BTU
INPUT
STATIC
PRESSURE
FILTER
(
O
F) (WOOD) ( "WATER) (2)
H
2O
2000 N/A G-10 1/3 4 950 68 70000 0,2 0,4 11 x 20
3000 N/A G-10 1/3 4 1300 78 110000 0,2 0,6 12 x 24
4000 N/A G-10 1/3 4 1300 128 180000 0,2 0,6 12 x 24
4000 G-12 3/4 2 N/A 1800 93 180000 0,2 0,8 12 x 24
4500 G-12 3/4 2 N/A 1800 121 235000 0,2 0,8 12 x 24
5000 G-12 3/4 2 N/A 2600 125 350000 0,2 1,45 20 x 24
TECHNICAL DATA – ELECTRIC MODE
MODEL OUTPUT
(C.F.M.)
TEMP. VAR.
(OF)
BTU/HR AMPERES
TOTAL
BREAKER
REQUIRED
FEEDER
GAUGE
VOLTAGE
SINGLE PHASE
ELEMENTS
QTY
15 KW 950
1300
50
36
51195 75 100 4 120/240 3 – 5 KW
18 KW 950
1300
60
44
61434 87 125 4 120/240 2 – 5 KW, 2 – 4 KW
20 KW 950
1300
67
49
68260 95 125 3 120/240 4 – 5 KW
25 KW 950
1300
1800
83
61
44
85325 115 150 2 120/240 5 – 5 KW
30 KW 1300
1800
73
53
102390 140 175 1 120/240 6 – 5 KW
WOOD 15 120

19
10. SELECTION CRITERIA (COMBINED WOOD/ELECTRIC FURNACE)
RESIDENTIAL AREA
House including: basement, first floor and second floor (half)
Floor area * New house Existing house
1100 square feet or less PSG 2000 – 15KW PSG 2000 – 18 or 20KW
1100 to 1450 square feet PSG 3000 – 18KW PSG 3000 – 20 or 25KW
1400 to 2000 square feet PSG 4000 – 20KW PSG 4000(G-12)– 25 or 30KW
2000 to 3000 square feet PSG 4500 – 25KW PSG 4500 – 30KW
COMMERCIAL AREA
Building including: Walls 14 to 16 feet high
Garage doors, no basement
Floor area
2500 to 3800 square feet PSG 4500- 25 or 30KW
4000 to 10000 square feet PSG 5000 – 40, 50 or 60KW
* Consider main floor only.

20
11. TROUBLESHOOTING
PROBLEM CAUSES SOLUTIONS
1. Sudden drop in heating
performance follows adequate
heating from first loadings.
Ash accumulation at lower intake
blocks combustion air intake and
causes deposits in heat exchanger
and flue pipes.
Clear air intake of any ash
accumulation.
Clean heat exchanger and flue pipes.
2. Insufficient heat from first loadings,
low draft
Wrong setting of draft regulator
(opening too large).
Restriction in chimney flue (excessive
length of chimney connector, right-
angled elbows).
Set draft regulator (reduce opening).
Reduce distance between furnace
and chimney and eliminate 90o
elbows.
Maximum length: 10 feet.
Tight-angle elbows: maximum 3.
3. Poor heating in the rooms while
hot air plenum and furnace are hot.
Inadequate duct installation.
Insufficient static pressure.
Unbalanced system (too many hot air
outlets for too few cold air intakes).
Reposition ducts.
4. Furnace burns too much wood. The thermostats controlling the air
combustion damper is located too
close to cold air and demands heat
continuously.
Wrong setting of air intake register.
Poor building insulation.
Ash drawer left open.
Furnace too small for heating needs.
Unbalanced ventilation system,
insufficient heat near thermostat.
Relocate thermostat.
Adjust chain between damper motor
and combustion air damper.
Balance the ventilation system as to
increase the flow air in room where
thermostat is located.
5. Fan starts too late. Fan starting temperature is too high.
Cold air return is too cold.
Inappropriate location of fan limit
control in hot air plenum.
Lower starting temperature (the fan
limit control is normally set at 150oF);
under certain conditions, this limit
should be reduced.
Reduce the cold air intake.
Relocate fan limit control within the
hot air plenum.
6. Creosote accumulation, very
average performance.
Damp wood.
Insufficient draft.
Clogged chimney.
Use dry wood.
Adjust draft regulator.
Clean chimney, chimney connector
and furnace heat exchangers.
7. Hot air plenum remains barely
warm while furnace in full operation.
Damp wood.
Too much cold air return in relation to
hot air ducts.
Unbalanced ventilation system.
Use dry wood.
Balance ventilation system.
IMPORTANT NOTE
WE STRONGLY RECOMMEND CONSULTING A HEATING SYSTEM SPECIALIST
FOR THE INSTALLATION OF A CENTRAL HEATING VENTILATION SYSTEM.
N.B.: STOVE BUILDER INTERNATIONAL INC. IS NOT LIABLE FOR ANY FAULTY INSTALLATION WHICH RENDERS THIS
UNIT INOPERATIVE