1
PRO3710 and PRO3710BN
Available in Polished Chrome and Brushed Nickel.
Single Handle Pull-Down Kitchen Faucet
Installation Steps:
1. Turn off water supply. Remove existing
faucet if necessary.
Remove preassembled mounting
hardware from faucet.
4. Slide rubber washer and metal washer
onto shank of faucet body. Secure
faucet body to sink with lock nut and
preassembled screws.
2. Without deck plate installation: Install
faucet body through top of sink
(not included).
3. With deck plate installation:
Place a bead of clear silicone sealant
(not included) around the base of the
putty plate. Place putty plate and deck
plate on sink (not included).
Insert faucet body through deck plate.
1 1/2"Max
(63mm)Max
1 1/4"~ 1 1/2"
(32mm~ 38mm)
2 7/8"Max
(73mm)Max
1 1/4"~ 1 1/2"
(32mm~ 38mm)
© 2021
Made in China
Cover your drain to avoid losing parts. Check with local plumbing code requirements before installation. The fittings should be installed by
a licensed plumber. When installing flexible hose, there should be no torsion or deformation; DO NOT fold into V or L shape; DO NOT
use if there are any cracks or deformations.
Warning and Notes:
Pipe tape
Hex wrench
Philips Screwdriver
Adjustable wrench
Pliers
Silicone sealant
Tools:
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft damp cloth only.
DO NOT USE harsh chemicals or cleaners as they may harm the protective finish.
®
5. Before connecting hose adaptor, please remove the cap first. Attach
lower end of spray hose to central supply tube in facuet.
A. Push quick connect hose assembly firmly upward until unable to
push any further. You will hear a clear "CLICK" sound.
B. Pull down on quick connect hose assembly, if you can not pull off,
then quick connect hose assembly is secure.
C. To remove the quick connect hose assembly, push quick connect
hose assembly upward, then press the clip and housing together to
pull down at the same time.
7. Attached water supply lines to the
faucet water supply tubes.
6. Attach the weight to cover the
weight locator label on the spray
hose. Use a Philips Screwdriver
(not included) to secure.
8. Remove spray head from Hose line.
Turn on water to flush out air/debris
when the water is clear and air is
purged turn off water at handle,
re-install spray head, turn back on
for 15 seconds and inspect for
leaks. (You need the spray head on
to create backpressure in the hose
to check for leaks.)
PRO3710 and PRO3710BN
PRO3710-WB and PRO3710BN-WB
Available in Polished Chrome and Brushed Nickel.
Single Handle Pull-Down Kitchen Faucet
Installation Steps:
1. Turn off water supply. Remove existing
faucet if necessary.
Remove preassembled mounting
hardware from faucet.
4. Slide rubber washer and metal washer
onto shank of faucet body. Secure
faucet body to sink with lock nut and
preassembled screws.
2. Without deck plate installation: Install
faucet body through top of sink
(not included).
3. With deck plate installation:
Place a bead of clear silicone sealant
(not included) around the base of the
putty plate. Place putty plate and deck
plate on sink (not included).
Insert faucet body through deck plate.
1 1/2"Max
(63mm)Max
1 1/4"~ 1 1/2"
( 32mm~ 38mm)
2 7/8"Max
(73mm)Max
1 1/4"~ 1 1/2"
( 32mm~ 38mm)
Cover your drain to avoid losing parts. Check with local plumbing code requirements before installation. The fittings should be installed by
a licensed plumber. When installing flexible hose, there should be no torsion or deformation; DO NOT fold into V or L shape;
use if there are any cracks or deformations.
Warning and Notes:
Pipe tape
Hex wrench
Philips Screwdriver
Adjustable wrench
Pliers
Silicone sealant
Tools:
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft damp cloth only.
DO NOT USE harsh chemicals or cleaners as they may harm the protective finish.
5. Before connecting hose adaptor, please remove the cap first. Attach
lower end of spray hose to central supply tube in facuet.
A. Push quick connect hose assembly firmly upward until unable to
push any further. You will hear a clear "CLICK" sound.
B. Pull down on quick connect hose assembly, if you can not pull off,
then quick connect hose assembly is secure.
C. To remove the quick connect hose assembly, push quick connect
hose assembly upward, then press the clip and housing together to
pull down at the same time.
7. Attached water supply lines to the
faucet water supply tubes.
6. Attach the weight to cover the
weight locator label on the spray
hose. Use a Philips Screwdriver
(not included) to secure.
8. Remove spray head from Hose line.
Turn on water to flush out air/debris
when the water is clear and air is
purged turn off water at handle,
re-install spray head, turn back on
for 15 seconds and inspect for
leaks. (You need the spray head on
to create backpressure in the hose
to check for leaks.)
