QualGear QG-PRO-PM-SCA-W User manual

C Anchor
IMPORTANT! Do not loosen screws all the way when making adjustments,
this will disconnect the parts and may cause injury or property damage.
To connect the 1.5" NPT pipe (sold separately) to the ceiling adapter, twist the male threaded end
into the female thread of the adapter. Then secure the position with screws (F or G) using the
allen key (I). Decorative cover (H) can be attached post-installation to make the appearance look tidy.
Alley Key
(I)
Decorative Cover
(H)
OR
(G) x 2
(F) x 2
Ceiling Adapter
1.5" NPT Pipe
(not included)
r.
CAUTION!
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
45.5kg
(100lbs)
RATED
Version November 2015
5 Year Limited Warranty
Version November 2015
5 Year Limited Warranty
QG-PRO-PM-SCA-W
Attaching the 1.5" NPT Pipe to the Suspended Ceiling Adapter
4

y.
1 2
Parts Checklist
Please read the entire installation manual before you start installation and assembly.
NOTE
Hardware Package
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
[email protected] for replacement parts and do not start assembly and installation
until you receive all the parts.
Ceiling Tray
A (x1)
Wire
B (x1)
Allen Key
I (x1)
Concrete
Anchors
C (x4)
Eye Bolts
D (x4) Turnbuckles
E (x4)
IMPORTANT: Installers must verify that the supporting surface will safely
support the combined weight of the equipment and all attached hardware
and components.
Do not begin to install your QualGear
product until you have read and understood
all the instructions and warnings contained
in this installation manual. If you have
any questions regarding the instructions,
for US customers please contact
QualGear customer support via email at
[e-mail]. For all international
customers, please contact your local
distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may
cause damage or serious injury. QualGear is
not liable for the improper use or installation
of its products.
Make sure that the supporting surface
will safely support the combined load of the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
equipment.
Tighten screws firmly, but do not over
tighten. Over tightening can damage the
items, greatly reducing their holding power.
ALL QUALGEAR products are intended
for indoor use only and any outdoor use voids
the limited warranty. For warranty information,
please visit:
http://www.qualgear.com/warranty.php
Never exceed the maximum rated weight
specified in this manual.
All hardware must be used at the
designated points in the installation
instructions to prevent property damage
and/or personal injury.
This product was designed to be
compatible with all standard 1.5" NPT
pipes.
WARNING
Maintenance
Please check that the ceiling adapter is secure and safe to use at regular intervals. If you have any
questions regarding any of the instructions or warnings, please contact your local distributor (OR)
contact QualGear technical support via email at [e-mail].
M5 x 5mm
Screws
G (x2)
M5 x 5mm
Security Screws
F (x2)
Decorative Cover
H (x1)

Mounting to a Wooden Joist or Wooden Stud Ceiling
1a Mounting to a Concrete Ceiling 1b
For concrete ceiling mounting, follow
Step 1b, and for truss, follow Step 1c.
NOTE
3 4
Using a straight edge, mark the centerline
of the stud, and the locations of where you
want to mount the ceiling adapter.
Using an edge-to-edge stud finder, find the
edges of the stud.
1 2
SKIP TO STEP 2
Stud Finder
Mark the locations of where you want to
mount your suspended ceiling adapter.
1
Using a power drill and a 1/4" masonry drill bit,
drill four holes of 1/4" (6.0 mm) diameter and
1.5" (38 mm) depth at the marked locations.
drill diameter
ø 6.0mm
(ø 1/4")
drill depth
38mm
(1.5")
2
SKIP TO STEP 2
Using a power drill and a 5/32" wood drill bit,
drill holes of 5/32" (4mm) diameter, and
2" (51mm) depth at the marked locations.
Install the eye bolts into the drilled holes, then
loop wire (B) into the hole of the eye bolts and
twist several times to secure.
drill diameter
ø 4.0mm
(ø 5/32")
drill depth
51mm
(2.0")
3 4
Mark the drill locations on the center of the studs
for security.
Eye Bolt (D)
3
Insert and hammer the concrete anchors (C)
into the drilled holes. Loop a wire at the end of
each anchor and twist around itself a few
times to secure.
Concrete
Anchor (C)
Make sure drilled holes are free of dust
so the anchors will be set properly.
TIP

2
5 6
WARNING
Installers are responsible to provide hardware for other types of mounting situations.
 Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
Loop wire around the truss and twist around itself several times to secure.
Mounting to a Truss
1c
Attaching the Ceiling Tray to the Suspended Wire
2
Adjusting the Collar Position
3
TrussTruss
Attach the suspended wire from previous step to the turnbuckles (E). Hook turnbuckles to the
ceiling tray and adjust until the ceiling tray is leveled and suspended above the ceiling tile.
Suspended Wire
Turnbuckles
(E)
Wire (B)
Wing Nuts
Ceiling Tray
Before attaching the 1.5" NPT pipe, loosen the wing nuts
and slide the collar on the ceiling tray to the desired position.
Then tighten the wing nuts to secure the position of the collar.
Collar can be adjusted to the desired position
by sliding within a distance of 1' (310mm).
Collar
Ceiling Tray