QYSEA 5057202 User manual

User Manual for
U-QPS(Underwater Quick
Position System)

Contents
Introduction and packing list··········································································································01
Out of box audit······················································································································02
Product specification··············································································································03
Usage instructions···························································································································04
Installation································································································································ 05-16
Operation································································································································· 17-23
Maintenance and after-sales support····················································································24
Disclaimer········································································································································25
00

01/ Introduction and Packing List
1
Serial
Number
Item Name
Quantity
Unit
1
U-QPS Box
1
PCS
2
Antenna
1
PCS
3
Adapter
1
PCS
4
AC cable
1
PCS
5
U1
1
PCS
6
TypeC USB cable
6
PCS
7
MINI USB to ethernet cable
8
PCS
8
U-QPS Bracket
1
PCS
9
U-QPS Mount
1
PCS
10
M3X16 inner hexagon screw
4
PCS
11
M4X16 inner hexagon screw
6
PCS
12
M3X6 inner hexagon screw
6
PCS
13
Φ2.5 inner hexagon wrench
1
PCS
14
Φ3 inner hexagon wrench
1
PCS
15
User manual
1
PCS

Before operating FIFISH products, please be sure to receive relevant training and
take practices, and read this document thoroughly before performing underwater
operations. Operations in violation of QY safety rules may result in the consequence
that your safety and interests cannot be guaranteed.
1. Regarding the damages to accessories and underwater vehicle caused by unauthorized modification,
disassembly or opening in violation of regulations, or damages to accessories and underwater vehicle caused
by improper installation, improper use or operations not in accordance with official regulations, QY doesn’t
bear any legal responsibility and the warranty will also be ineffective.
2. When installing the accessories, the power supply of the underwater vehicle shall be shut down.
3. Please check whether all the parts of the 500ml water sampler are complete. If there is any part missing,
please contact QY after-sales service personnel in a timely manner.
4. Please check whether all interfaces, plug-ins and O-rings are kept dry and tidy, otherwise they should be
replaced as soon as possible.
02/Out of Box Audit
2

03/Product Specification
Item
Specification
Locator Depth Rating
300m
Locator Operating Temp.
-5℃~60℃
Locator Battery lifetime
~10hours
Locator Range
100m or 300m
Locator Directivity
Omnidirectional ( 360degrees)
Receiver Operating Temp.
-10℃ ~ 60℃
Receiver Transducers
4x
Receiver Directivity
Omnidirectional ( 360degrees)
Max range
300m
Frequency
31.25-250KHz
Cable
10 meters
3

04/ Usage Instructions
Precautions before usage
2. Before usage, please check whether all accessory interfaces, plug-ins, and O-rings are damaged or missing,
and whether they are kept dry and clean.
3. Before connecting the U-QPS with the underwater vehicle, the underwater vehicle shall be powered off.
3. Check the battery level of the underwater vehicle to ensure that there is sufficient and stable power.
5. Before entering the water, please check whether the probes and connectors of the accessories are tightly
sealed.
6. When connecting to the connectors of the underwater vehicle, it must be aligned with the positioning pin,
forcible inserting may cause damage to the connector.
6. Check whether the underwater robot and the remote control are working normally when connected to the
connector on the underwater vehicle.
7. Check the batteries of mobile phones, tablet PCs and laptops.
8. After-sales mailbox: [e-mail]
4

05/Installation
1.Signal transmitter U1 (referred to as "U1")
5
1.1 Mounting bracket: load the QPS bracket onto U1 (do not tighten the U1 bottom cover before use)
signal transmitter U1 screw
U-QPS bracket

05/Installation
2.Install the locator on the FIFISH PRO V6 PLUS
6
Topside Antenna Locator U1 FIFISH PRO V6 PLUS

05/Installation
2. Install the locator on the FIFISH PRO V6 PLUS
7
1 2
3 4
5

05/Installation
3. Open the back cover of U1
turn the rotary switch at the back to the appropriate channel
and then tighten the back cover until the indicator light is on
1
2
3
8

05/Installation
4. Install and fix the antenna
12
4
65
3
9

05/Installation
5. Connect the antenna to the second port of topside
10
6. Turn the IP switch on topside to 192.168.2.94
12
3
1 2

05/Installation
7. Connect the network port of topside
11
1
2 3

05/Installation
8. Connect the remote controller with the FIFISH special
network cable
12
1 2
3

05/Installation
9. Connect the power supply
13
9.1 Connect the power supply and turn on the power switch
10. Connect the battery
10.1 Connect the battery（The battery need to buy with yourself）and turn on the power switch
12
3 4

05/Installation
11. Connect the battery
14
11.1 Connect the battery（The battery need to buy with yourself）and turn on the power switch
1 2
3 4
5 6
7 8

05/Installation
12. Connect the WiFi of the remote control, open the FIFISH app
and enter the UQPS setting interface
Set up the channel of U1, longitude and latitude of topside and
antenna The direction and scope of the search
15

05/Installation
13. Observe whether the U1 indicator light
and the GPS indicator light on topside are always on in green
16
1 2
3

05/Installation
14. The antenna is starting to receive signal
17

06/Operation
1. Open the FIFISH app
click the botton of map
18