Rapsodo GOLF SIM STUDIO ENCLOSURE 13 User manual

Golf Simulator Studio Bu
4m x 3m x 3m / 13 (W) x 10 x
Assembly instru o
Golf Simulator Studio Bundle 13 Deep Enclosure

Packaging
Your Go f Simu ator Enc osure wi come in 2 separate cartons.
1 x ong carton - meta frame & 1 x rectangu ar carton -
enc osure materia with screen
Packaging 01

A
FemaleMale 27 x 3.3ft (1m) pole
B
MaleMale 11 x 3.3ft (1m) pole
C
FemaleMale 1 x 2ft ( .6m) pole
F
HoleMale 1 x 3.3ft (1m) pole
HoleMale HDMI cable
Packaging 02
Long carton contents

Long carton contents
Packaging 03
1
2 x 10 ˚ 3-way connector
2
2 x 10 ˚ 3-way connector
4
2 x 2-way feet connector
5
2 x 3-way feet connector
X
2 x crossover clamp 1 x Mounting Bracket

Packaging 04
1 x Enclosure material with Screen
It is a single piece construction containing the
pro ector screen, side and ceiling panels
9 x Clip
1 x Replacement Hitting Screen (attached on inside
of Enclosure Material with Velcro)
2 x Clip with Velcro
Rectangular carton contents

Poles
Frame Assembly Identification Parts 05
A
AA
B
A
B
A
A
B
A
A
B
A
A
B
A
A
AA
B
A
AA
B
A
AB
A
AB
A
AB
A
AB
A
A
FC

Connectors
4
4
2
1
2
1
5
5
Frame Assembly Identification Parts 0
The arrows on the angled 3-way connectors should point toward each other. For example, the label on
front left 3-way (1) should face you and the arrow points to the right; the front right 3-way (2) should point
to the left (see insert images). Both the top bars should have a slight arc from left to right.
Front Left (1)
Front Right (2)

Step 1
Assemble the upper frame by connecting the poles as shown on Figure 1
5 .52°
A
B
A
BA
B
A
B
A
AA
B
A
A
A
B
A
AB
A
A
B
2
1
2
1
Assembly – STEP 1 0
Figure 1

Step 2
Attach projector mounts to the upper frame
57.52°
Assembly STEP 2 08
A
A
FC

Step 3.1
Place the material in the centre of your enclosure area and spread the black material out so that you can
identify the bottom of the screen
The front of your hitting screen (wear you hit the ball into) is the smooth side.
Assembly – STEP 3.1 09

Step 3.2
Secure all 4 top edges of the enclosure material to the upper frame using the elcro attachments as
shown on Figure 
Start at the rear, before moving on to each side.
Assembly – STEP 3.2 10
Figure 2

Step 3.3
Secure material to the projector pole using the Velcro attachments as shown on Figure 2
Assembly – STEP 3.3 11
Figure 2

Step 3.4
Secure material to the upper left frame using the Velcro attachments as shown on Figure 2
Assembly – STEP .4 12
Figure 2

Step 3.5
Secure material to the upper right frame using the Velcro attachments as shown on Figure 2
Assembly – STEP .5 1
Figure 2

Step 3.6
Secure material to the upper front frame using the Velcro attachments as shown on Figure 2
Assembly – STEP .6 14
Figure 2

Step 3.7
Three clips and velcro need to be attached on the top of the enclosure
Velco straps are already sewn on the enclosure.
Assembly – STEP 3 7 15
Attach clip to Velcro.
Hook it over the back bar.
Pull rmly and reattach strip
to the Velco.

Step 4
Once the top is secured, attach the enclosure to each of the vertical upright legs as shown on Figure 1
Assembl – STEP 4 16
Figure 1

Step 5
Assemble the lower frame as shown on Figure 4
Assemb y – STEP 5 17
Figure 4

Step 6
Wrap and secure the remaining perimeter edges to the frame using the Velcro attachments as shown on
Figure 2
Assembl – STEP 6 18
Figure 2

Step 7
Tighten screen with clips and velcro on the back side of the enclosure.
Assembl – STEP 6 19
Attach clip to Velcro.
Hook it over the back bar.
Pull rmly and reattach strip
to the Velco.