RED CAT MPX-110 User manual

MPX-110 Assembly Guide

Table of Contents
Tool List………………………………………..…………………….Page 3
Removal From Crate…………………………...…………………..Page 4
Parts Inventory………………………………………….…………..Page 8
Assembly……………………..…………………………………....Page 10
Oil Change……………………………………………..…………..Page 27
Initial Start-Up…………………………………………………...…Page 30
Other Information…………………………………..……………...Page 33
2

Tool List
- Ratchet handle
- Sockets
- 8mm
- 10mm
- 12mm
- 13mm
- 15mm
- 17mm
- 18mm
- 21mm
- 23mm
- Wrenches
-10mm
-13mm
- Phillips head screwdriver ( + )
- Slotted screwdriver ( - )
- Standard Pliers
- Drain Pan
- Funnel
3

Removal From Crate
NOTE: Some crates are incorrectly labeled VX-110 MKII. Disregard this.
1) Remove (4) white straps from crate.
2) Cut side of cardboard box and discard.
3) Remove plastic wrap covering top of ATV.
4

4) Cut blue ties from hardware box, handlebars and wheels and tires.
a. NOTE: Wheel spacers are tied to front wheels and are needed to
complete assembly.
5) Remove (10) 12mm hex head bolts from bottom of cage.
6) Remove (2) 12 mm hex head bolts from steering stem cross brace.
5

7) Remove top portion of cage.
8) Remove hardware box, grill insert, handlebar cover, rear skid plate, grab bar and
front bumper.
6

9) Remove rear axle clamps from both sides of ATV.
10) Inspect entire ATV for any shipping damage. File any shipping damage claim at
http://www.redcatmotors.com/dealer_warranty.asp?stepid=2&sel=freight .
7

Parts Inventory
1) After setting parts aside, ensure none are missing.
1 – Rear Wheel and Tire – PN 100388
2 – Hardware Box – See page 9
3 – Front Wheel and Tire – PN 100459
4 – Grill Insert – PN 101146
5 – Handle Bar Cover – Part Number Varies with color. See website.
6 – Front Bumper – PN 101199
7 – Rear Skid Plate – PN 101200
8 – Grab Bar – PN 101201
9 – Tail Light – PN 100161
10 – Side Reflector – PN 100276
8

Hardware Box
1 – Rubber Hub Cap – PN 101202
2 – Owner’s Manual – PN 101203
3 – Wire Tie – PN 101097
4 – Handlebar Clamps – PN 100147
5 – 1.25” Cotter Pin – PN 101094
6 – 1.5” Cotter Pin – PN 101093
7 – Tool Kit – PN 100093
If any parts are missing, please file a claim form at
http://www.redcatmotors.com/dealer_warranty.asp?stepid=2&sel=freight .
9

Assembly
1) With assistance, remove ATV from crate bottom and place on ATV jack.
2) Tie Rod
a. Slide tie-rod end up through steering knuckle.
b. Secure with lock washer, 17mm hex castle nut and 1.25” cotter pin.
10

2) Tie Rod (cont.)
c. IMPORTANT – Be sure to bend cotter pin as shown to keep castle nut
from backing out.
d. Repeat for other side.
11

3) Front Shock
a. Remove front shock bolt from mounting bracket.
b. Line up shock with mounting bracket.
c. Insert 13mm hex head bolt and install 15mm hex lock nut.
d. Repeat for other side.
12

4) Front Brakes
a. Remove blue tie from front brake assembly.
b. Remove 19mm hex castle nut from steering knuckle.
c. Line up slot in brake plate with locating tab on steering knuckle.
d. Slide brake assembly into place.
5) Front Wheels and Tires
a. Slide front wheel onto steering knuckle.
i. IMPORTANT – Ensure wheel spacer is in place.
b. Install and tighten 19mm hex castle nut.
c. Install 1.5” cotter pin.
13

5) Front Wheels and Tires (cont.)
d. Install rubber hub cap.
6) Rear Wheels and Tires
a. Install and tighten (4) 15mm hex lock nuts on inside of rear wheel.
14

6) Rear Wheels and Tires (cont.)
b. Remove 23mm hex castle nut and washer from rear axle.
c. Slide wheel onto axle.
d. Install washer onto axle.
e. Install and tighten 23mm hex castle nut and install 1.5” cotter pin.
f. Install rubber hub cap.
g. Ensure tightness of (4) lug nuts.
15

7) Lower ATV and remove jack.
8) Handlebars
a. Place lower handlebar clamp on steering stem and position handlebars.
16

8) Handlebars (cont.)
b. Install (2) upper handlebar clamps and (4) 10mm hex head bolts.
c. Position handlebars to desired angle.
d. Tighten (4) 10mm hex head bolts.
9) Side Front Fender Brace
a. Install 10mm hex head bolt through slot in fender brace into frame.
i. IMPORTANT – Install both sides before tightening.
b. Tighten both sides.
17

9) Side Front Fender Brace (cont.)
10) Center Front Fender Brace
a. Install and tighten 8mm hex head bolt through brace, into frame.
18

11) Fender/ Toe Guard Brace
a. Insert Phillips head screw through fender and toe guard.
b. Install 10mm hex nut on opposite side of Phillips head screw and tighten.
19

12) Grill Insert
a. Remove packing material from grill insert.
b. Remove (2) chrome Phillips head screws from top of fender.
c. Install grill insert.
d. Install (2) chrome Phillips head screws and tighten.
20