RedKnows SBX-3 Series User manual

1. Insert the SIM card,
according to the picture
to the right.
Check before inserting:
a. SIM card must be active
(some GSM providers
insist that the SIM card is
registered before use).
b. That you have credits on
your prepaid phone card
c. That the PIN code is inactive and that no voice
mail is activated (check by inserting the card into a
mobile phone) Check with your GSM provider if you
are not sure.
d. Caller ID support (verify that the telephone num-
ber of incoming calls are displayed by inserting the
SIM card into a mobile phone)
e. Check that you inserted the SIM card the right
way up (see the picture above)
f. The unit must be turned off before you insert the
SIM card (there should be no connection
to ground, and no connection between the two
black cables). This is also what you should do if you
want to disengage the alarm during a longer period
– make sure there is no connection to ground or
between the two black cables.
Take your time while following the instructions be-
low. Should it take too long between each step the
alarm will go into its “sleep mode”. Wake it up again,
simply by pressing the unlock-button on the remote
control. When pressing the unlock-button, the RF
LED should be turned on. This means the remote
control has contact with the SBX-3. If this doesn’t
work, see SBX-3 operating manual.
2. Connect the SBX-3 as shown in the diagram on
the next page. The red cable is connected to (+) and
the two black cables to ground (-). If the grey cable
is not being used, connect it to ground (-). Make
sure you have good GPS - & GSM reception.
3. Now the SBX-3 unit will read the SIM card. The
red GPS LED is on and the green SYS LED is as-
hing.
4. Press the T button four times
on the remote control, and then
the SOS button once. The SIM card
is initialized with the basic settings (SETUP code
and phone book entries). The red GPS LED is as-
hing, and the green SYS LED is on.
5. Wait until both the yellow GSM LED and the
green SYS LED are ashing. The red GPS LED
should be on, steady or ashing, depending on
whether it has established contact with the GPS sa-
tellites. In other words, all LEDs are ashing when
the system is activated! (You don’t have to wait for
the red LED to start ashing before you go to step
6.) Note! The red GPS LED should have started to
ash within 60 minutes from activating the alarm.
6. Now it is time to enter www.redknows.com and
specify the phone numbers that should receive
SMS from the SBX-3, and which number that
should receive status SMS or listen through the
microphone.
Click on “EZStart redKnows” in the menu and
create a personal account by entering an e-mail
address as your user name and a password. If
needed, change language in the menu at the upper
right. The account you create is personal. Save you
user name and password!
a. Click on ap 2, Personal info, and enter your
personal information. Don’t forget to save! (Click
on SAVE) At the bottom of the page is the button
”Generate Document”, you click on when you want
to print out a document to send to your insurance
company (in case they will give you a discount for
installing a GPS alarm & tracking system).
b. Continue to ap 3, Checklist and do the check
stated before you continue with the next step.
c. Basic Setup, ap 4. Enter the mobile phone
number (SIM-card number) for the SBX-3 and the
mobile number for alarm receiver 1 (e.g your own
mobile phone). Don’t forget to save before continu-
ing to the next step! (click on SAVE)
d. Flap 5, Advanced settings. Under advanced set-
tings you can choose to enter mobile numbers to
other alarm receivers. At the bottom of the page you
enter the settings for the Geofence alarm. We re-
commend to set the Geofence at 0,08. Don’t forget
to click on SAVE.
e. Continue to Send, ap 6. By clicking on the Send
button one or two SMS will be created, depending
on the amount of information in the message. If
two SMS are being created, you will have to click
on send once more after a couple of minutes. The
information is sent to your SBX-3.
Quickstart - redKnows SBX-3 Mini Tracker
TURN OVER

Note! If need to make changes later on in your set-
tings (mobile numbers or personal info), you should
ALWAYS click Save on the page where you have
made your changes. After that, go to ap 6 (Send),
click on Clear History and after that on the Send
button.
7. Now the SBX-3 is ready to use. Call the SBX-3
from your mobile phone number dened in EZStart.
The SBX-3 will deny the call resulting in a busy tone
or an error message from the operator. You will
receive an SMS with position and status information
within a minute.
8. Use your remote control to activate or deactivate
the alarm. For more information – see operating
manual.
1 White
Check list
The siren beeps three times when you activate
the alarm with the remote control.
This warns you the alarm cannot be activated, since
one of the sensor input is active.
No SMS is received when you call your SBX-3
- Check GSM reception in area
- Call again
- Check placement of GSM antenna
- Check/re-enter settings on website
- Is pincode on SIM-card removed?
- Caller ID-support must be active
- Is voice mail disconnected (some operators
must do it for you)
- GPS reception. Is red GPS LED ashing?
Place antenna as freely as possible. Test!
NOTE! The same mobile phone number cannot be
used for both status SMS and for listening to the mi-
crophone. Two different numbers must be used.
Circuit diagram
Antenna (for remote control)
2 Orange
Not active
3 Yellow
Relay (option)
4 Green
Siren
5 Brown/white
Input. Not active
6 Blue
Door trigger (option),
NO. Positive activation
8 Purple
Sensor1 input. A vibration sensor
can be connected. (option) NO.
Negative activation. 3 impulses
within 6 sec. to trigger alarm.
9 Grey
Sensor2 input. The magnetic
contact can be connected. NC.
Positive activation. (This input
must be grounded if not used).
11 Brown
Ignition key input. Positive
activation.
12V
SBX-3
GPS
Microphone
GSM-antenna
12 Black
Built-in spare battery. Ground
10 Red
7 Black
Fuse
I/O specications:
Main battery: 12 V,
24V or 10V -30V.
Input 6, 11: Max 30V
Output 3: Max 300 mA
Main battery
Axtech AB
St Jörgens väg 4, S-422 49 Hisings Backa, tel. +46 (0)31-558866, fax. +46 (0)31-558869
Axtech, Quickstart SBX-3,
Other manuals for SBX-3 Series
2
Other RedKnows GPS manuals
Popular GPS manuals by other brands

Navman
Navman TRACKER 5100I Installation and operation manual

Enfora
Enfora MT-G quick start guide

Garmin
Garmin GPSMAP 392, 398, 492, 498 Quick reference guide

Flexcom
Flexcom TKSTAR TK905B Installation and operating instructions

Magellan
Magellan SporTrak SporTrak Color user manual

Spectracom
Spectracom VersaPNT Getting started guide