Reece Mizu Stream Extended Basin Mixer Quick start guide

STREAM EXTENDED BASIN MIXER CHROME
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
To see the complete MIZU range go to
www.reece.com.au/bathrooms
Dimensions are nominal measurements only.
Disclaimer: Products in this specification manual must by regulation be installed by licensed and
registered trade people. The manufacturer/distributor reserves the right to vary specifications or
delete models from their range without prior notification. Dimensions are nominal measurements only.
Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor
takes no responsibility for printing errors.
Tech Page Version 1
TM
WMK022094
AS/NZS 3718
192
150
Ø42
Ø50
M8
max 35
225
305
The more
stars the more
water efficient
WATER R ATIN G
www.waterrating.gov.au
In accordance with AS/NZS 6400
Licence No. 0025
Reece Limited
6.0 litres per
minute
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Colour Chrome, Matte Black or Brushed Nickel
Pressure Rating
Maximum continuous operating pressure1000kPa.
Note: As per AS/NZS3500 pressure must be
limited to 500kPa on any new home, extension or
renovation.
Note: For best performance and longer life we
recommend an operating pressure between
150 - 500kPa.
Temperature Rating Maximum Continuous Working Temperature 65°C
Suitable Hot Water Units
Storage Tank
Continuous Flow
Gravity Feed
Ye s
Ye s
No
Cartridge Type Ceramic Disc

STREAM EXTENDED BASIN MIXER CHROME
INSTALLATION INSTRUCTIONS
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Note
Mixer must be installed by a licenced plumber
Important
Your mixer comes to you already factory assembled and tested. We do not recommend the dis-
mantling of any internal part of the mixer. The mixers are factory tested and sealed so as to give
the best performance.
Installation Procedure
1. Please flush out new pipe work prior to connecting the new mixer
2. All mixers should be installed with isolating stop cocks (Arco)
3. This tap is suitable for high pressure applications where both hot and cold water supply
pressures are at 150kPa or above
4. Place the base washer & dress ring (14) into position
5. Fit the tap body into the basin hole making sure first that the flexible connectors are firmly
tightened into base of the body
6. Do not use teflon tape on threads
7. From underneath apply your washer prior to positioning the horse shoe plate
8. Lock the mixer into position by tightening the lock nut
Servicing - Replacement of Cartridge
1. Remove cap and unscrew grub screw using allen key
2. Lift off handle and remove cartridge dome, unscrew brass locking nut and lift out cartridge
3. Replace cartridge, brass locking nut and handle. Tighten grub screw and push in indicator
cap
Servicing - Flow Regulator (If flow rate drops)
1. Remove cartridge as outline above.
2. Remove flow regulator (7) and flush with water or replace.

STREAM EXTENDED BASIN MIXER CHROME
COMPONENT LISTING
No. Description
1
Handle Complete
2
3
4 Cartridge Dome
5 Cartridge Locknut
6 Cartridge
7 Flow Controller
8 O-Ring
9 Grub Screw
10 Mixer Body
11
Aerator Complete12
13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
22
21 20
No. Description
14 Dress Ring
15
Fixing Kit
16
17
18
19
20 Cartridge Seat
21 Flexible Hose (Cold)
22 Flexible Hose (Hot)