Riley Hopkins FLASH FORCED AIR User manual

RILEY FLASH FORCED AIR
Assembly Instructions

2
Tools Required:
What’s in the box
IMPORTANT: BE SURE ALL PARTS ARE ENCLOSED BEFORE ASSEMBLING.
• (x2) 1/2” open end wrench
• (x1) Phillips screw driver
Tag Part # Item Q.
1AF2-4000RH-H AIR FLASH HEATER 1
297-011 UPPER TUBE 1
313-141 COLLAR 1 7/16 ID 1
497-184 BENT BOLT 1
593-022 KNOB 5/16-18 X 1”L STUD 2
697-190 TUBE ASSEMBLY 1
790-580 LEVELING FEET 5/16-18 5
897-003 LEG 24” 5
922-015 COLLAR 5/16 2
10 25-243 SCREW-10-32 X 1/2 TAPTITE 3
11 25-025 BOLT 5/16-18 X3/4 SERRATED 10
12 24-012 NUT 5/16-18 SERRATED 10
13 24-014 INSERT NUT 5/16-18 5
1. Position Heater Head [1] face on flat level surface.
2. Install feet [7] to legs [8].
3. Install legs [8] to tube [6] with screw [10], bolt [11], & nut [12].
4. Install tube [2], collar [3], and bent bolt [4] into tube [6].
5. Slide tube [2] up & lock collar [3] to mate with heater head [1] bracket.
6. Install knobs [5] & collars [9] through bracket & into upper tube.
7. Rotate knob to level heater face to platen.
8. Tighten knobs [5] & collars [9] to retain level heater.

3
General Operating Instructions:
1. Adjust height of heater above platen to suit specific conditions.
2. Rotate knob to level heater above platen.
3. Adjust temperature heat seing.
4. Air Flash will heat to operating temperature in approximately 5 minutes.
5. All operating/curing temperatures should be checked with a temperature monitoring
device of your choice.
6. Pretest all curing situations, inks, and substrates before proceeding.
7. Position magnetic handle for operator convenience.
HEAT PRODUCING UNIT
DO NOT LEAVE HEATER
UNATTENDED
7
12
11
10
8
6
43
2
59
1
LEVELING KNOB
DOWN FLANGE

MANUFACTURE’S WARRANTY
All products are warranted against defects in workmanship at the time of shipment. The
obligation under the above warran shall be limited to the repair or replacement of any
part or parts manufactured by the dryer manufacturer without charge F.O.B. factory that
may prove defective within 12 months from the date of shipment, which are returned to
dryer manufacturer. The above warranties are the only warranties made with respect to the
equipment. There is no implied warran of merchantabili or of fitness.
EXCLUSIONS: There is no warran on parts not manufactured by the dryer manufacturer,
other than the respective manufacturer’s warran, if any. The warran against defects shall
not extend to damage caused from any of the following:
• Transport by carrier
• Corrosion
• Operation or use in a manner inconsistent with specifications and/or operating
instructions
• Ordinary wear, accident, improper installation, or maintenance
• Alterations made to equipment in any way
Dryer manufacturer shall not be liable for losses or damages, including but not limited to
incidental or consequential damages, suered or incurred because the equipment proves
to be defective either upon installation or during its operation or use. Shipment of defective
parts to the dryer manufacturer and the return shipment of any repaired or replacement
parts from the dryer manufacturer shall be the purchaser’s/user’s expense.
Ryonet Corp. - [phone] - www.screenprinting.com
FDIF-RC-AF4000_122021_C