ROADWORX TM-X User manual

TM-X
Desktop Stand
Assembly Instructions

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
Internet: www.thomann.de
31.10.2022, ID: 540250, 540252, 540254, 540257, ...

Table of contents
1 Safety instructions................................................................................................................................................................................................................ 4
2 Overview.................................................................................................................................................................................................................................... 6
3 Installation................................................................................................................................................................................................................................ 8
4 Technical specications................................................................................................................................................................................................... 20
5 Protecting the environment.......................................................................................................................................................................................... 30
Table of contents
TM-X 3
Desktop Stand

1 Safety instructions
Intended use
This product is intended for stable xing and adjustable installation of monitors, tablets, speakers or similar. Use the product only as
described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in
personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intellectual abilities and having corresponding
knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is respon‐
sible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not in the reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the product. They could swallow the pieces and choke! Never
let children play unattended with the product.
CAUTION!
Danger of tipping when transported under load
If the stand is moved without having removed the installed device, the stand may tip over and cause injuries and property damage. Remove
the installed device before transporting the stand.
Safety instructions
4TM-X
Desktop Stand

CAUTION!
Danger of tipping due to overload
In case of overload, the stand may tip over and cause injuries and property damage. Never exceed the maximum load capacity specied for
the stand.
Safety instructions
TM-X 5
Desktop Stand

2 Overview
For the TM-X stand system the following items are available:
ö
#-
. /
$
%
&
'
( ) * + ,
0
23
1
4
Overview
6TM-X
Desktop Stand

No. Item name No. Item name
1 Roadworx TM-X Pole 300 Clamp (item no. 540259) 11 Roadworx TM-X Tablet Holder (item no. 540268)
2 Roadworx TM-X Pole 470 Clamp (item no. 540264) 12 Roadworx TM-X VESA Mount (item no. 540267)
3 Roadworx TM-X Pole 660 Clamp (item no. 540262) 13 Roadworx TM-X Laptop Holder (item no. 540269)
4 Roadworx TM-X Pole 300 Fixed (item no. 540261) 14 Roadworx TM-X Studio Monitor Holder (item no. 540270)
5 Roadworx TM-X Pole 470 Fixed (item no. 540265) 15 Roadworx TM-X Bar 970 (item no. 542186)
6 Roadworx TM-X Pole 660 Fixed (item no. 540263) 16 Roadworx TM-X Bar 1200 (item no. 542188)
7 Roadworx TM-X Arm 65 (item no. 540250) 17 Roadworx TM-X VESA Mount 180 for Bar (item no.
542190)
8 Roadworx TM-X Arm 180 (item no. 540252) 18 Roadworx TM-X VESA Mount 385 for Bar (item no.
542189)
9 Roadworx TM-X Arm 385 (item no. 540254) 19 Roadworx TM-X Thread Option (item no. 540257)
10 Roadworx TM-X Stand Mount (item no. 540271)
Overview
TM-X 7
Desktop Stand

3 Installation
–Place all components on a suitable mounting surface for mounting. Use a soft padding to prevent damages to the surfaces.
–The illustrations are for illustrative purposes and may dier from the actual product.
Installation
8TM-X
Desktop Stand

TM-X Pole Clamp (item no. 540259, 540264, 540262)
Loosen the locking screw of the clamp and place the clamp on the desk edge. Tighten the locking screw of the clamp.
Installation
TM-X 9
Desktop Stand

For adjusting the desktop stand height, loosen the Allen screws using an Allen key. Adjust the desired height and tighten the Allen
screws using an Allen key.
Installation
10 TM-X
Desktop Stand

TM-X Pole Fixed (item no. 540261, 540265, 540263)
Loosen the locking screw and place the stand in the recess of the desktop. Tighten the locking screw.
Installation
TM-X 11
Desktop Stand

TM-X Arm (item no. 540250, 540252, 540254), TM-X Stand Mount (item no. 540271)
Open the cover of the desktop stand TM-X Pole Clamp (item no. 540259, 540264, 540262) or TM-X Pole Fixed
(item no. 540261, 540265, 540263).
Slide the arm or the holder from the top in the recess of the desktop stand. Adjust the desired arm height and tighten the Allen
screws using an Allen key.
Replace the cover on the desktop stand. Pay attention to the correct location of the positioning pins of the cover.
Installation
12 TM-X
Desktop Stand

TM-X Tablet Holder (item no. 540268)
Loosen the locking screw and place the tablet holder in the recess of the TM-X Arm (item no. 540250, 540252, 540254). Tighten the
locking screw.
Loosen the locking screw of the mounting hole and adjust the tilt of the tablet holder up to 90°. Tighten the locking screw.
Loosen the locking screws of the supporting arms, pull out the supporting arms completely and place the tablet in the corner sup‐
ports of the lower supporting arms.
Adjust the corner supports to the thickness of the tablet. Make sure that the tablet sits rmly in the corner supports. Tighten the
locking screws of the corner supports.
Reinsert the supporting arms and x the tablet. Tighten the locking screws of the supporting arms.
Installation
TM-X 13
Desktop Stand

TM-X VESA Mount (item no. 540267)
Loosen the locking screw and place the monitor holder in the recess of the TM-X Arm (item no. 540250, 540252, 540254). Tighten
the locking screw.
For adjusting the monitor holder tilt, loosen the Allen screws using an Allen key. Adjust the desired tilt and tighten the Allen screws
using an Allen key.
Mount the monitor with four screws and washers to the monitor holder.
Installation
14 TM-X
Desktop Stand

TM-X Laptop Holder (item no. 540269)
Loosen the locking screw and place the laptop holder in the recess of the TM-X Arm (item no. 540250, 540252, 540254). Tighten the
locking screw.
For adjusting the laptop holder tilt, loosen the Allen screws using an Allen key. Adjust the desired tilt and tighten the Allen screws
using an Allen key.
For adjusting the clamping range of the laptop holder, pull out the lateral clamping jaws at the sides of the the laptop holder. Make
sure that the laptop sits rmly between the clamping jaws.
Installation
TM-X 15
Desktop Stand

TM-X Studio Monitor Holder (item no. 540270)
Loosen the locking screw of the speaker holder and slide him on the arm. Tighten the locking screw.
Slide the arm with the speaker holder from above in the recess of the desktop stand TM-X Pole Clamp (item no. 540259, 540264,
540262) or TM-X Pole Fixed (item no. 540261, 540265, 540263). Adjust the desired height of the arm and tighten the Allen screws
using an Allen key.
For adjusting the speaker holder tilt, loosen the Allen screws using an Allen key. Adjust the desired tilt and tighten the Allen screws
using an Allen key.
Installation
16 TM-X
Desktop Stand

TM-X VESA Mount for Bar (item no. 542189, 542190)
Remove the rubber plugs and slide the arm in the holder. Place the rubber plugs in the recesses of the arm.
Loosen the locking screw of the monitor holder and place the monitor holder in the recess of the arm. Tighten the locking screw.
For adjusting the monitor holder tilt, loosen the Allen screws using an Allen key. Adjust the desired tilt and tighten the Allen screws
using an Allen key.
Mount the monitor with four screws and washers to the monitor holder.
Installation
TM-X 17
Desktop Stand

Installation
18 TM-X
Desktop Stand

TM-X Bar (item no. 542186, 542188)
Loosen the Allen screw using an Allen key. Remove the Allen screw, the washer and the hex nut, and remove the bar from the
holder. Place the holder in the recess of the desktop stand TM-X Pole Clamp (item no. 540259, 540264, 540262) or TM-X Pole Fixed
(item no. 540261, 540265, 540263)
Slide the TM-X VESA Mount for Bar (item no. 542189, 542190) on the bar and tighten the locking screw.
Place the ready-equipped bar in the holder, insert the Allen screw, the washer and the hex nut, and tighten the Allen screws of the
bar using an Allen key.
Installation
TM-X 19
Desktop Stand

4 Technical specications
Roadworx TM-X Pole Clamp
Item name Roadworx TM-X Pole 300 Clamp Roadworx TM-X Pole 470 Clamp Roadworx TM-X Pole 660 Clamp
Item no. 540259 540264 540262
Desktop thickness up to 76 mm
Length 300 mm 470 mm 660 mm
Weight 1.84 kg 2.16 kg 2.5 kg
Max. load capacity 50 kg 50 kg 50 kg
Material Aluminium
Compatible with Roadworx TM-X Arm 65 (item no. 540250)
Roadworx TM-X Arm 180 (item no. 540252)
Roadworx TM-X Arm 385 (item no. 540254)
Roadworx TM-X Stand Mount (item no. 540271)
Roadworx TM-X Bar 970 (item no. 542186)
Roadworx TM-X Bar 1200 (item no. 542188)
Technical specications
20 TM-X
Desktop Stand