Roborock Zeo One User manual

Roborock Zeo One
Washer Dryer User Manual
Read this user manual carefully before using this product and store it
properly for future reference.

03
English 03
Deutsch 28

04
Contents
05 SafetyInstructions
09 InstructionsforUse
10 ProductOverview
10 ConnectingtotheApp
10 InstallationRequirements
11 Installation
13 HowtoUseDetergent
14 ControlPanel
17 Features
18 ProgramTable
19 Maintenance
20 Speci󽗉cations
23 FAQ
24 Troubleshooting
27 CircuitDiagram

05
Safety Instructions
Please read the following safety instructions carefully, and install and use the machine as instructed.
•This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety (CB).
•Children should be supervised to ensure that they do not play with the appliance.
•This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall
not play with the product. Cleaning and user maintenance shall not be made by children without supervision (EU).
•Children of less than 3 years should be kept away unless continuously supervised (EU).
•The removed packaging materials should be disposed of in time to keep out of reach of children or prevent children from swallowing them.
•Do not place any heavy objects, exothermic appliances and objects that may leak on the machine, or it may be damaged.
•Do not operate the machine when ammable gases (such as coal gas) leak.
•The room must be well ventilated to avoid the gases owing from the machine from igniting other substances in the room, including open ames.
•Do not place the machine on a non-ventilated rug that may block its bottom vent.
•To avoid the danger arising from resetting the thermal circuit breaker by accident, do not power on the machine during reset.
•Do not pile up combustibles and sundries (such as cotton waste) around the machine.
•There are glass parts in the machine. If they are damaged by accident, please dispose of or replace them in time to avoid injury.
•When you pull out the detergent drawer to add detergent, please be careful not to bump into or get scratched by its hard corners.
•If the machine is transported in an environment where the temperature is below 0°C in winter, put it at room temperature for 3 hours before turning it on.
•Whenever the machine is to be transported, reinstall its transit bolts to prevent damage to it during transportation.
•When handling the machine, please grip the base of the packaging cabinet instead of the protruding parts of the machine, especially its control panel or door.
•Please do not touch any hot parts of the machine during or at the end of the drying process, or burns may occur.
•Do not change the power cord without permission, or accidents may happen.
•If the machine makes any abnormal noise or emits a burnt smell, please stop using it immediately and unplug it.
•The tumble dryer is not to be used if industrial chemicals have been used for cleaning.
•The lint trap has to be cleaned frequently, if applicable.
•Lint must not to be allowed to accumulate around the tumble dryer.
•Do not dry unwashed items in the tumble dryer.
•Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol,kerosene, spot removers, turpentine, waxes and wax removers should
be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
•Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows tted with foam rubber pads should
not be dried in the tumble dryer.
•Fabric softeners, or similar products, should be used as specied by the fabric softener instructions.
•Remove all objects from pockets such as lighters and matches.
•For appliances with ventilation openings in the base, a carpet must not obstruct the openings.

06
Safety Instructions
•The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a
way that a full opening of the tumble dryer door is restricted.
•The rated capacity and dry capacity of this product are 10.0 kg and 6.0 kg respectively and its operating water pressure is 0.1-1.0 MPa.
•This appliance is intended to be used in household and similar applications such as:
– sta kitchen areas in shops, oces and other working environments;
– farm houses;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments;
– areas for communal use in blocks of ats or in launderettes.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid a hazard.
•The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
•For appliance having ventilation openings in the base, the installation instructions shall state that the openings must not be obstructed by a carpet.
•Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
•The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and o by a utility.
•Most spare parts of your appliance are available for a minimum of 10 years after placing the last appliance on the market. If you have any questions, please
contact our customer service at:
Email: [e-mail]
Ocial website: https://support.roborock.com/hc/de
Address: Roborock Germany GmbH, Harstr.47,40591 Düsseldorf
Warning!
Risk of electric shock.
Never try to repair an appliance which is defective or presumed to be defective. You may put your own and future users' lives in danger. Only authorised
specialists are allowed to carry out this repair work.
Improper repair will void the warranty and subsequent damages can't be recognised!
WARNING

07
EU Declaration of Conformity
We Shenzhen Roborock Innovation Technology Co., Ltd., hereby, declares that this equipment is in compliance with the applicable Directives and European
Norms, and amendments. The full text of the EU declaration of conformity is available at the following internet address: https://global.roborock.com/pages/
compliance
WiFi Specication
Service Protocol Frequency Range Max. Output Power
WiFi 802.11b/g/n 2400-2483.5 MHz ≤20dBm
WEEE Information
Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where
the product was purchased. They can take this product for environmental safe recycling.
International Symbols Explanation
– PROTECTIVE EARTH (Protective Ground) symbol [symbol IEC 60417-5019 (2009-02)]
Safety Instructions

08
Plug the machine into a 230V~/50Hz
three-prong outlet, which should be
correctly and reliably grounded. No
extension cord is allowed.
Power o the machine before
cleaning or performing maintenance.
Never plug or unplug the machine
with wet hands.
Keep the machine away from
rain or severe humidity. Use
it at temperatures between 0
and 40℃.
Be sure to watch out for children
or pets to prevent them from
getting into the drum, and keep
them away from the machine
while it is running.
Do not spray water or other
liquids onto the machine.
Keep lit cigarettes, candles,
or other re sources
as well as volatiles and
inammables away from the
machine.
Do not wash or dry clothes
stained with gasoline,
alcohol, petroleum, benzene,
thinner or other chemicals.
Connect the machine to the
tap with a new water inlet
hose, and replace the hose
in time in case of damage or
leakage.
Do not wipe the body and parts
of the machine with ammable,
explosive, and soluble chemicals,
or put them into the machine.
When the machine is running,
the door glass may get hot.
Please do not touch the glass,
or allow pets to touch it.
Do not allow children or the
elderly and the vulnerable to
use the machine on their own.
To avoid danger, the damaged
power cord of the machine must
be replaced by a professional
sent by the service department
of the manufacturer.
Safety Instructions
Hazardous or unsafe acts that may cause personal injury or property damage.
Grounding
Warning

09
Instructions for Use
Do Not Wash
First Use
Notes on Washing
•The machine is subject to water-based tests before leaving the factory. It is
normal that a small amount of water remains in the drum, gasket, and on
the door glass.
•For the rst time of use, please make sure to install the machine correctly
and run a drum clean with clean water.
•There may be smells given o by rubber parts at rst, but they will
gradually disappear after the machine is used a few more times.
•Please check the clothing care labels carefully before washing and
perform as instructed.
•Stubborn stains should be handled manually before washing.
•For delicate and expensive clothing, and small items like socks, please put
clothing into laundry bags.
•For wool or silk clothing that should be washed with a specic detergent, be
sure to turn o Auto Dosing and put the detergent into the drum manually.
•Do not put too many clothes into the drum above the highest washing
capacity, or they may not be fully cleaned.
•It is recommended to separate your clothes by color before washing to
avoid color bleeding.
•The machine may not work properly during the spin cycle if washing one piece
of clothing or a few pieces of heavy or highly absorbent clothing due to uneven
weight distribution. It is recommended to add more items to the cycle.
•It is recommended to open the door for ventilation after washing every
time to prevent the drum from growing mold or giving o odors.
Drum Drying
Notes on Drying
•Please check the clothing care labels carefully before drying and perform
as instructed.
•It is recommended not to dry too many clothes in one load, or they may
not be fully dried.
•It is recommended to dry large items such as bed sheets and curtains
separately for the optimum drying eect.
Do not drum dry clothes that
have been treated with chemicals
such as bleach or degreaser.
Do not drum dry items that are
easy to expand, such as a sleeping
bag, duvet and large blanket.
Do Not Dry
Clothes marked with the symbols
above cannot be drum dried, or
they may be damaged.
Do not drum dry clothes made of
special materials, such as printed
clothing, rubber, leather and fur
lining.
Hang to Dry
Dry Flat
Do Not Iron
Dry in Shade
•Please keep the tap on during drying to avoid inadequate water supply or
low water pressure, which may degrade the drying eect.
•During drying, the remaining time displayed is estimated time, which may
slightly vary with the weight of the clothes and the Dry program due to
smart adjustment.
•The drying eect is subject to various factors, such as the selected
Wash+Dry/Dry program as well as the material and amount of clothes.
•Please do not tap "Start/Pause" and open the door during drying, or the
clothes may not be fully dried or the machine may malfunction after the
drying is resumed.
•Clothes may stretch or shrink to varying degrees after drying depending
on their materials.
•After drying ends, the door cannot be opened immediately until it has
cooled to a temperature that is safe to touch.
•The RPM will automatically increase in the programs under the Wash+Dry
mode. Protect delicate clothing and do not select this mode when washing
and drying delicate clothing.

10
Accessories
Product Overview
Detergent Drawer
Top Cover
Control Panel
Gasket
Power Plug
Drain Pump Flap
Drain Hose
Drum
Door
Check all accessories shown in the picture above. If the machine is damaged or the
accessories are missing during transportation, please contact the dealer.
Connecting to the App
1. Scan the QR code to download and install the
Roborock app.
2. Open the app, and tap "Scan to Connect" or "+" to
add an appliance.
3. Follow the instructions in the app to complete the
connection.
4. The WiFi ( ) lamp is always on, indicating that the
appliance is connected to the network.
Scan to download the APP
Note: Tap and hold the "Rinse" button for 3 seconds to reset WIFI.
User Manual
×1
Transit Bolt
Cover ×4
Noise Reduction
Pad x 4
Wrench ×1Water Inlet
Hose ×1
Installation Requirements
Installation Environment
•Place the washing machine on a level, rm, and non-slip surface. Do not
install it on a base or shelf.
•Keep the washing machine in a well-ventilated place away from direct
sunlight and freezing weather.
•The working environment temperature should be 0°C - 40°C.
•Keep the washing machine away from heat sources such as charcoal res
or gas stoves.
Top: ≥25mm
Sides: ≥25mm
Front: ≥550mm
Rear: ≥50mm
25mm
25mm
25mm
Water Supply
Power Supply
•The washing machine requires a water pressure of 0.1MPa to 1.0MPa.
Water pressure lower than 0.1MPa may cause abnormal water inow. In
this case, the washing machine may not work properly and will display the
prompt [E1].
•Place the washing machine as close to the faucet as possible; Check the
inlet valve and all connections of the faucet for leakage.
•Do not connect the washing machine to a hot water source.
•Connect the washing machine to a power supply (230V~/50Hz) which
should be correctly and reliably grounded.
•Make sure the power cord is not pinched by any objects.

11
3. Remove the double-sided adhesive
protective lm from noise reduction
pads and then paste pads around
the bottom of machine (two longer
pads in position 1 and 3, two shorter
pads in position 2 and 4).
4. Finally set the machine
upright again.
Installing the noise reduction pads (optional)
Removing the transit bolts
1. Unscrew the four transit bolts
by turning them counterclock-
wise using a wrench (Which is
attached to the foam support-
ing board).
2. Pull out the bolts and
keep them properly (for
use during transportation).
1. Find four noise reduction
pads on foam supporting
board.
2. Carefully lay the washing ma-
chine down on its rear side with
leveling feet toward the operator.
Be careful not to break the glass
parts (control panel and door) of
the machine.
3. Cover the transit bolt holes
with transit bolt covers.
Installation
1
3
2
4

12
3. Rotate the leveling feet to
obtain desired height.
4. Tighten the leveling foot bolts
to ensure the four leveling
feet are level.
Connecting the water inlet hose
1. Align the water inlet hose to
the water inlet and tighten it.
2. Connect the water inlet hose to the wa-
ter system (3/4 " faucet) and make sure
that everything is connected rmly.
3. Check the connections for leakage.
In case of leakage, please check if
the above requirements are met
and the steps are followed.
Adjusting the leveling feet
1. Press the top cover of
the washing machine
with both hands. If the
machine shakes, please
adjust the leveling feet.
2. Loosen the leveling foot
bolts by turning to the left
with a wrench.
Installation
Water inlet
Water inlet hose External thread faucet
Water inlet hose

13
Connecting the drain hose
•Connect the drain hose with one of the three installation methods above.
•Do not remove xing clips from the drain hose, or drainage may fail.
•To prevent scalding, do not touch the discharged hot laundry water during high-tempera-
ture washing.
•If the drain hose is too long, consider cutting it shorter. Do not forcibly shove it back into the
washing machine. Otherwise, it may cause abnormal noise.
•Do not bend the drain hose, or drainage may fail.
•If an extension pipe is required, make sure the extension pipe is less than 1.5m in length and
0.2m in height to avoid poor drainage.
c. When inserted directly into a
oor drain
To prevent gravity drainage, the drain
hose was securely fastened with clips
before leaving the factory. To ensure
proper drainage performance, please
do not remove the clips or x the
drain hose at a height lower than
0.65m from the ground.
a. When xed to a sink
The end of drain hose should be
xed rmly with a sling no higher
than 1.2m from the ground, and
its end should not be immersed in
water.
b. When connected to a branch
tailpiece
The end of drain hose should be
connected to a branch tailpiece, with
its highest point no lower than 0.65m
from the ground.
Notes:
Min. 0.65m
Max. 1.2m
Min. 0.65m
How to Use Detergent
Auto Dosing
•Do not add detergent and softener above the MAX line, and lock the sealing
caps after addition.
•Add detergent and softener before operating the machine. When there is
not enough detergent/softener in the detergent drawer, the detergent/
softener light on the control panel will keep ashing as a reminder to add
detergent/softener. If you ignore the reminder, the clothes will be washed
with clean water after the detergent/softener is used up.
• The Auto Dosing can be enabled/disabled on the control panel or in the app.
•The dose of detergent/softener can be adjusted in the app.
Manual Dispense Mode
•If you choose to add detergent manually, be sure to turn o Auto Dosing,
or the clothes may not be fully rinsed.
•If you use washing powder/disinfectant/laundry pods, put them into the
drum directly before washing and turn o Auto Dosing.
•If you use wool/silk-specic detergents, please put them into the drum
as instructed and turn o Auto Dosing.
Detergent Compartment
Sealing Cap
Softener Compartment
Detergent Drawer Button
•It is recommended to use low-sudsing detergent for front-load washers.
•Do not pull the detergent drawer out while the machine is running, or the dispense
function may not work properly or water may overow.
•When the machine is not used for a long time and the detergent becomes lumpy or sticky,
dilute it with a small amount of warm water to prevent clogging.
•Do not put cleaning agents other than detergent/softener into the detergent drawer, or
the dispense function may not work properly.
Notes:
Installation

14
Control Panel
󹌰 
󹌯Delay Start:
Tap to select a dryness option from Iron/Cupboard/Cupboard Plus, and this
setting defaults to Cupboard/Cupboard Plus.
After selecting a program, tap to increase the time
after which the program will start by 30 minutes on the display (max
24 hours). Tap the Start/Pause button to confirm the Delay Start, and
the program will start when the schedule time counts down to zero.
Then the time displayed will be switched to the estimated time of the
selected program.
󹌮Temp.: After selecting a program, tap to select the desired water
temperature from cold(--)/20°C/30°C/40°C/60°C/90°C. Some programs
may limit the water temperature for clothing material protection.
󹌪
Tap to turn the machine on, and tap and hold for 2 seconds to turn the
machine o. The machine will automatically shut down if left inactive for 10
minutes.
󹌫Start/Pause
Tap to start/pause a program. Tap during running to unlock the door and
add clothes mid-cycle. When the water level or temperature is too high to
open the door, the Door Lock Lamp will ash, with a beep as well as "Locl-"
and the remaining time displayed alternately on the screen.
󹌬Spin Speed/Remote Control
After selecting a program, tap to select the desired spin speed from No Spin/
400/600/800/1000/1200/1400 RPM. Some programs may limit the RPM for
clothing material protection. Tap and hold the "Spin Speed" button for 3
seconds to activate remote control.
󹌭
After selecting a program, tap to select a desired number of
rinses from 1/2/3/4/5.
󹌱Auto Dosing
Tap to enable or disable the dispense of detergent/softener.
141 1
15
14


15
󹌲
When it stays on, it indicates that the Detergent Auto Dosing is enabled
and there is enough detergent; when it ashes, it indicates that there is
insucient detergent; and when it is o, it indicates that the Detergent
Auto Dosing is disabled.
When it stays on, it indicates that the Softener Auto Dosing is enabled
and there is enough softener; when it ashes, it indicates that there is
insucient softener; and when it is o, it indicates that the Softener Auto
Dosing is disabled.


Display:
Delay Start Lamp
Door Lock Lamp 
WiFi Lamp
When it stays on, it indicates that the wait time is being set; when it ashes,
it indicates that the time is counting down; and when it is o, it indicates
that there is no delay start or the program is running.
When it stays on, it indicates that the door is locked; when it ashes, it
indicates that the door cannot be opened at the moment; and when it is
o, it indicates that the door is unlocked.
When it stays on, it indicates that the machine is connected to the network
and can be remotely controlled with the app; when it slowly ashes, it
indicates that the machine is waiting for network connection; when it
quickly ashes, it indicates that the machine is connecting to the network;
and when it is o, it indicates disconnection.
It shows dierent statuses of programs, including the remaining
time, delay start time, error code, temp., rinses, and RPM.



14 14
Remote Control On Indicator Light 
When the icon lights up, the remote control is on, and when it goes o, the
remote control is o.
14
15
Child Lock Lamp
When the machine is running, tap and hold Temp. and Rinse for 3 seconds
to enable/disable the child lock. If the lamp stays on, it indicates that the
feature is enabled, and all buttons except Power and the said combination
buttons of child lock are disabled; when it is o, it indicates that the feature
is disabled.

Control Panel

16
Operating Procedure
Wash+Dry
Wash
Dry
Select Mode Select Program Set Program Parameters
(this step can be skipped)
Start Program
•Program parameter settings such as "Delay Start" and "Temp." can only be adjusted after
a program is selected.
•When the machine is running, touch any program icon on the screen, and the drum lamp
will automatically switch on.
Notes:
Iron The clothes contain a little moisture after drying and are
ready for ironing.
Cupboard The clothes are skin-friendly and ready for immediate
wearing after drying.
Cupboard Plus The clothes are thoroughly dry and can be folded up and
put away after drying.
Drying Level Description
Modes
Wash+Dry: Wash, and then dry.
Wash: Wash only, without drying.
Dry: Dry only, without washing.
Control Panel
Program Description
Eco 40-60
Eco 40-60 program is able to clean normally soiled cotton
laundry declared to be washable at 40°C or 60°C , together in
the same cycle, and that this program is used to assess the
compliance with the EU ecodesign legislation.
Cotton Suitable for fabrics such as cotton and linen.
Synthetics Suitable for synthetic clothing.
Wool Recommended for 2kg or less of machine washable wool
fabric (it is optimal to use special detergent for wool fabric).
20°C Washing brightly colored clothes for better protection of
colors.
APP Program
You can add special laundry programs in the Roborock
app to "APP Program" for quick access on the control
panel, with "Intensive" by default.
Bedding Recommended for 5kg or less of four-piece bedding,
curtains, and other large fabrics.
Anti-Allergen
90°C high-temperature washing, with 60°C healthy washing
by default. Multiple rinses to remove common allergens
such as dust mites and pet dander.
Quick Quick wash for a small amount of lightly-soiled clothes.
*Recommended for 1kg or less of clothes.
Rinse+Spin Recommended for separate rinsing or spinning of 10kg or
less of clothes.
Spin Recommended for 10kg or less of clothes that need
spinning only.
Drum Clean Rinses the drum at high temperature with special
detergent (as needed). Note: Do not add clothes.

17
Features
Mid-Cycle Adding Power Outage Memory
Remote Control
Door Lock/Unlock
Wool Care-Green
Tap Start/Pause to add clothes during mid-cycle. This feature is only
available when the water temperature is less than 50°C, the water level is
below the door viewing window, and the machine is not performing drying.
If there is a power outage when the machine is running, the machine will
resume the current cycle after the power comes back on. During a power
outage, please do not force the door open. If you need to do so, enable
"Emergency Door Opening".
Press and hold the "Spin Speed" button for 3 seconds to activate remote
control. Then you can control the washer remotely through the Roborock app.
Prerequisites:
•The washer has been connected to your WiFi network.
•The washer has been connected to the Roborock app.
•The washer door has been closed.
Deactivate Remote Control:
•When the washer is not operating, press the "Power" button to deactivate
the remote control;
•When the washer is operating, press the "Pause" button, and the remote
control will be deactivated automatically once the door is unlocked;
•When the washer is paused with its door locked, press and hold the "Spin
Speed" button for 3 seconds to deactivate the remote control;
•Press and hold the "Power" button to deactivate the remote control.
After the Wash program is started, the door is automatically locked, and
the door lock lamp is always on. After the program is paused/ended, the
door is automatically unlocked with the door lock lamp o when the door
opening conditions are met. Unlocking is unavailable when the water level or
temperature is high during running. If you do need to open the door, enable
"Emergency Door Opening".
Emergency Pull Ring
Drain Pump
Emergency Drain hose
Emergency Door Opening
In case of an emergency, pull the emergency pull ring to open the door, and
then reset the pull ring after the door is opened. (Note: The emergency pull
ring is on the lower right of the machine, and must not be used during a
regular wash cycle. Before opening the door, please make sure all the water
is drained out and be careful not to get burned).
The wool wash cycle of this machine has been
approved by The Woolmark Company for the
washing of wool garments labelled as “hand wash”
provided that the products are washed according
to the instructions on the garment label and those
issued by the manufacturer of this washing machine.
M2309:WD10001RR4Z.

18
Program Table
Name Capacity
≤(kg)
Temperature (°C) Rinse (Time(s)) Spin (r/min) Drying Level Auto Dosing
Cold 20 30 40 60 90 1 2 3 4 5 No
Spin 400 600 800 1000 1200 1400 Iron
Cupboard Cupboard
Plus
Detergent Softener
Eco 40-60 10 / / / / ●/ / ●/////////●/ / / ● ●
Cotton 10 √√√●√√√●√√√√√√√√●√/ / / ● ●
Synthetics 4√ √ ●√ √ /√●√ √ /√√√√●√/ / / / ● ●
20℃ 5/●/ / / / √●√√√√√√√√●/ / / / ● ●
Quick 1●√ √ √ / / ●√///√√√●√/ / / / / ● ●
Bedding 5√√√●√/√●√√√√√√√●√/ / / / ● ●
Anti-Allergen 5/ / / / ●√ √ √ ●√√√√√√●√/ / / / ● ●
Wool 2√ √ ●√/ / √●√/ / √√√●/ / / / / / ● ●
Rinse+Spin 10 / / / / / / ●√ √ / / √√√√√●√/ / / / ●
Spin 10 ///////////√√√√√●√/ / / / /
Drum Clean -/ / / / ●√/●//////●/ / / / / / / /
Eco 40-60 6/ / / / ●/ / ●/////////●/●/● ●
Cotton 6√√√●√√√●√√√/////√●√●√● ●
Synthetics 3√ √ ●√ √ /√●√ √ /////√●/√●√● ●
20℃ 5/●/ / / / √●√√√//// / √●√●√● ●
Quick 1●√ √ √ / / ●√/////////●√●√● ●
Bedding 5√√√●√/√●√√√/////√●√●√● ●
Anti-Allergen 5/ / / / ●√ √ √ ●√ √ /////√●√●√● ●
Wool 1√ √ ●√/ / √●√/////●/ / / / ●/● ●
Rinse+Spin 6/ / / / / / ●√ √ ///////√●√●√/●
Spin 6////////////////√●√●√/ /
Drum Clean -/ / / / ●√/●//////●/ / / / / ●/ /
Eco 40-60 6/////////////////●/●/ / /
Cotton 6///////////√////●√ √ ●√/ /
Synthetics 3///////////√///√●/√●√/ /
20℃ 5///////////√////●√ √ ●√/ /
Quick 1///////////√/////●√●√/ /
Bedding 5///////////√////●√ √ ●√/ /
Anti-Allergen 5///////////√////●√ √ ●√/ /
Wool 1//////////////●/ / / / ●/ / /
Drum Clean -/////////////// / / / / / ●/ /
●means "default",√means "available", / means "not available", - means "N/A"
* The parameters for each program may vary slightly due to the continuous software development and upgrades.
Wash+DryDry Wash

19
Body and Gasket (Clean after each use) Detergent Drawer (Clean as needed)
Drain Pump Filter Element (Clean monthly)
2. Wipe the gasket with a soft
cloth, and remove the foreign
objects (if any) from the groove.
1. Wipe the body with a soft
cloth and a detergent
that contains no corrosive
materials.
1. Press the detergent drawer button
to pull the detergent drawer out.
(Be careful not to break the glass panel).
1. Press to open the drain pump
ap, and pull the emergency
drainpipe to drain the residual
water.
2. Rotate anticlockwise to take
the lter element out, and
clean the waste on it.
2. Rinse with water, pour o the
residual water, wipe the drawer
dry, and reinstall it.
Maintenance
Inlet Valve Filter (Clean monthly)
4. Put the lter element back
into the drain pump and
tighten it, and close the
drain pump ap.
3. Check for and remove any
foreign objects from the
drain pump.
1. Turn o the tap and unscrew
the water inlet hose.
3. Clean the threaded part of
the inlet valve with a brush.
4. Reconnect the water inlet
hose to the tap and turn on
the tap to check for leakage.
2. Take the inlet valve lter out
with needle-nose pliers and
rinse it.

20
Maintenance
Instructions for Maintenance
Freezing Handling
Notes concerning the energy and water
consumption of the washing machine
If the machine is frozen in a place below 0°C, please handle as follows.
1. Wrap the tap with a warm towel to help defrost, and soak the removed
water inlet hose in warm water.
2. Pour warm water into the drum, close the door and let it inactive for 10 minutes,
and then reconnect the water inlet hose to the tap to ensure normal use.
•The most ecient programs in terms of energy consumption are generally
those that perform at lower temperatures and longer durations.
•Program time as well as energy and water consumption depend on
various factors, such as weight and type of the laundry, chosen functions,
characteristics of the water etc.
•For only slightly or normally soiled laundry, decrease the temperature of
the program, as the device uses less energy this way.
•Use the maximum spin speed available if the laundry will be dried
afterwards, as the remaining moisture content will be lower, which in
turn saves energy during the later drying process. Note, that noise and
remaining moisture content are inuenced by the spinning speed: the
higher the spinning speed in the spinning phase, the higher the noise and
the lower the remaining moisture content.
•Load the household washer-dryer up to the maximum capacity of each
program to reduce the energy-and water consumption.
•Always unplug the machine before cleaning.
•The disassembled parts must be reinstalled in place, inspected, and tested
before use.
•If hot water ows out of the drain pump, please wait until it cools down
before opening it, and be careful not to get burned.
•It is recommended to clean the inlet valve lter every month, or when the
error "E1" appears on the display.
•If Auto Dosing does not work properly, please check and clean the
connection between the detergent drawer and the machine.
•Regular cleaning is needed to avoid unnecessary service and prolong the
service life.
Specications
Name
Model
Rated Input Power for Wash
Rated Input Power for Spin
Rated Input Power for Heating
Max Power
Drying Power
Rated Voltage
Rated Frequency
Rated Volume
Waterproof Grade
Net Weight/Gross Weight
Dimensions*
Washer Dryer
WD10001RR4Z
200W
600W
1800W
2000W
1600W
230V~
50 Hz
72L
IPX4
83kg / 89kg
595 (W) × 660 (D) × 850 mm (H)
*The distance from the rear panel of the machine to its front door
(including the door).
•The program Eco 40-60 and Eco 40-60 Wash+Dry (cupboard) can be used to determine the values of the
energy label according to (EU) 2019/2023.