Roper Rhodes Henley T261102 Parts list manual

Customer Service
Tel: [phone] Fax: [phone]
Email: [email protected]
www.roperrhodes.co.uk
Roper Rhodes Limited
Brassmill Lane Trading Estate, Bath, BA1 3JF
REF: JS.RR.T261102 | 07.15 V2
Henley Basin Mixer
Installation & aftercare instructions
Please retain for future reference
Product code
T261102
ADJUSTING CERAMIC INDICES
To adjust the alignment of the ceramic indices, first
unscrew the bezel and ceramic indices assembly from
the tap handle.
The ceramic indices are held in place by a threaded brass
plate. Loosen the brass plate with a No. 16 Hex (Allen)
Key, but do not remove from bezel.
Rotate the ceramic indices until the printed logo is at the
desired position. You may need to screw the bezel and
indices assembly back onto the handle body to check
alignment and adjust as necessary.
When you are happy with the position, re-tighten the
brass plate , making sure to hold the ceramic indices still.
No. 16
Hex Key
Brass Plate
Ceramic Indices
Bezel
ADJUSTING HANDLE ALIGNMENT
To adjust the alignment of the handle in
relation to the body, unscrew the bezel and
ceramic indices from the top of the handle.
Unscrew the spindle bolt, and set aside
with the spindle bolt washer.
Lift the handle off the spindle and replace at
the desired angle using the micro
adjustment teeth.
Re-attach the washer and spindle bolt and
tighten.
Screw the bezel and ceramic indices
assembly back onto the handle body.
Bezel and Ceramic
indices assembly
Spindle Bolt
Washer
Spindle
Handle Body
Micro Adjust
teeth
Handle and Indices Adjustment:

REF: JS.RR.T261102 | 07.15 V2
MIN
25mm
 
Installation Diagram:
Aftercare Instructions
Installation Procedure:
Prior to installation flush out the pipe work to
remove debris and then ensure that the water
supply is turned off.
Refer to diagram and check that all components
are present.
1
2
Fit the flexible tail hoses to the basin mixer body
using an appropriate spanner, making sure that
you do not over tighten.
3
Connect the water supply to the flexible hoses.
Hot supply should always be connected to the
left hose (Flexible hose 1 in the diagram).
6
Fully open mixer on both hot & cold sides &
allow water to run for approximately one minute
to further flush the system.
7
Check all connections to ensure there are no
leaks.
8
Screw the threaded bars into their location
inside the mixer body.
4
Fit the mixer body to the basin using the
supplied rubber washer, metal washer and
fixing nuts in the order indicated in the drawing.
DO NOT over-tighten as this may damage the
basin. Remember to install the ruber o-ring
between the basin mixer body & the basin.
5
Whilst this item has a high quality durable finish, it should nevertheless be treated with care. Surfaces should be cleaned
using only a soft damp cloth and clean water & dried using a soft cotton cloth. Bath cleaning products, even non-scratch
ones could damage the finished surface.
Horseshoe Washer
Rubber Washer
Fixing Bolt
Metal Horseshoe Plate
Securing Bar
Basin
Pop-Up Waste Lever
Pop-Up Waste Lever
Pop-Up Rod Connector
Waste -
Washer
Basin Seal
Basin
We have complete confidence in this Roper Rhodes product and as such it is offered with a 10-year guarantee against defects in
manufacture. This tap must be fitted by a competent installer. If in doubt seek advice from a qualified professional. The guarantee requires
that this product be used in the manner for which it was intended and that it is installed & maintained in accordance with the fitting
instructions and local water bylaws. The guarantee covers products in domestic use only. The guarantee is invalidated should the tap be
damaged by water borne debris. Make sure that supply pipes are clear of any debris prior to installation, this is particularly important on new
plumbing installations. In the unlikely event that this product should fail during the guarantee period we will either replace the faulty part or
the complete unit as appropriate. Tap cartridges are subject to a 1-year guarantee. This guarantee covers damage against reasonable wear
and tear in use only. It does not cover damage incurred during installation, misuse or inappropriate maintenance. We recommend that the
cartridge is regularly cleaned in hard water areas to prevent lime scale build-up. Replacement cartridges are available to purchase by
contacting the Roper Rhodes Customer Service team. Failure to follow the terms outlined above will invalidate this guarantee. Proof of
purchase will be required to validate any guarantee claims.
10-YEAR GUARANTEE