Rotel RA-04 SE User manual

RA-04 SE
Stereo Integrated Amplifier
Amplificateur intégré stéréophonique
Stereo-Vollverstärker
Amplificador Integrado Estereofónico
Geïntegreerde Stereoversterker
Amplificatore Integrato Stereo
Integrerad Stereoförstärkare
ëÚÂÂÓ ËÌÚ„ËÓ‚‡ÌÌ˚È ÛÒËÎËÚÂθ
Owner’s Manual
Manuel de l’utilisateur
Bedienungsanleitung
Manual de Instrucciones
Gebruiksaanwijzing
Manuale di istruzioni
Instruktionsbok
àÌÒÚÛ͈Ëfl ÔÓθÁÓ‚‡ÚÂÎfl
SOURCE
T A P E
PHONES
MEDIA
PLAYER
RA-04SE
A
OFF B
A+B
SPEAKERS
POWER TREBLE BALANCEBASS AUX1
AUX2
CD
TUNER
PHONO
TONE
ON
Special Edition
Register your product at
www.Rotel.com/register

2RA-04SE Stereo Integrated Amplifier
Do not route the power cord where it will be crushed, pinched,
bent, exposed to heat, or damaged in any way. Pay particular
attention to the power cord at the plug and where the cord exits
the back of the unit.
The power cord should be unplugged from the wall outlet during
a lightning storm or if the unit is to be left unused for a long
period of time.
Use only accessories specified by the manufacturer.
Use only with a cart, stand, rack, bracket or shelf system recom-
mended by Rotel. Use caution when moving the unit in a stand or
rack to avoid injury from a tip-over.
Immediately stop using the component and have it inspected and/
or serviced by a qualified service agency if:
• Thepowersupplycordorplughasbeendamaged
• Objectshavefallenorliquidhasbeenspilledintotheunit
• Theunithasbeenexposedtorain
• Theunitshowssignsofimproperoperation
• Theunithasbeendroppedordamagedinanyway
Please use Class 2 Wiring when connecting the speaker terminals
of the unit to ensure proper insulation and minimize the risk of
electrical shock.
WARNING: There are no user serviceable parts inside. Refer all
servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electric shock,do not
expose the unit to moisture or water. Do not expose the unit to
dripping or splashing. Do not place objects filled with liquids, such
as vases,on the unit. Do not allow foreign objects to get into the
enclosure. If the unit is exposed to moisture, or a foreign object
getsintotheenclosure,immediatelydisconnectthepowercordfrom
the wall. Take the unit to a qualified service person for inspection
and necessary repairs.
Read all the instructions before connecting or operating the
component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and
on the product itself. Follow all operating instructions.
Clean the enclosure only with a dry cloth or a vacuum cleaner.
Do not use this unit near water.
You must allow a minimum 10 cm or 4 inches of
unobstructed clearance around the unit.
Do not place the unit on a bed, sofa, rug, or similar surface that
could block the ventilation openings. If the unit is placed in a
bookcase or cabinet, there must be ventilation of the cabinet to
allow proper cooling.
Keep the component away from radiators, heat registers, stoves,
or any other appliance that produces heat.
The unit must be connected to a power supply only of the type
and voltage specified on the rear panel. (USA: 120 V/60Hz,
EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied
power supply cable or an exact equivalent. Do not modify the
suppliedcable.Apolarizedplughastwoblades,withonewiderthan
the other. A grounding plug has two blades plus a third grounding
prong.Theseareprovidedfor yoursafety. Donotdefeatgrounding
and/orpolarizationsafety provisions.If the suppliedplug doesnot
fit your outlet, please consult an electrician for replacement of the
obsolete outlet. Do not use extension cords.
The main plug of the power cordset is a disconnect device of the
apparatus. In order to completely disconnect the apparatus from
the supply mains, the main plug of the power cordset should be
unplugged from the mains (AC) outlet. The stand-by LED indicator
willnotbelituptoshowthepowercordisunplugged.Thedisconnect
device shall remain readily operable.
Rotel products are designed to comply with
international directives on the Restriction of
Hazardous Substances (RoHS) in electrical and
electronic equipment and the disposal of Waste
Electrical and Electronic Equipment (WEEE). The
crossedwheeliebinsymbolindicatescomplianceand
that the products must be appropriately recycled or
processed in accordance with these directives.
Important Safety Instructions
This symbol means that this unit is double insulated.
An earth connection is not required.
Placetheunitonafixed,levelsurfacestrongenough
to support its weight. Do not place it on a moveable
cart that could tip over.

3
Figure 1: Controls and Connections
Commandes et branchements
Bedienelemente und Anschlüsse
Controles y Conexiones
De bedieningsorganen en aansluitingen
Controlli e collegamenti
Kontroller och anslutningar
é„‡Ì˚ ÛÔ‡‚ÎÂÌËfl Ë ‡Á˙ÂÏ˚
SOURCE
T A P E
PHONES
MEDIA
PLAYER
RA-04 SE
A
OFF B
A+B
SPEAKERS
POWER TREBLE BALANCEBASS AUX 1
AUX 2
CD
TUNER
PHONO
TONE
ON
Special Edition
1 2
3 5
4 6 7 8 9 0 - = q
w r t y u i o
INTEGRATED AMPLIFIER
MODEL NO. RA-04SE
POWER CONSUMPTION : 220W
SERIAL NO. RP-502
SPEAKER B
LEFTRIGHT
CLASS 2 WIRING
LEFTRIGHT
SPEAKER A
12V TRIGGER OUT
SPEAKER IMPEDANCE
A OR B - 40HMS MINIMUM
A AND B - 80HMS MININUM
PRE OUTTAPEAU X 2AU X 1TUNERCDPHONO
IN OUT
LEFT
RIGHT
GND
WARNING:TO REDUCE THE RISK OF THE FIRE OR ELECTRICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
DOUBLE INSULATION
When servicing
use only identical replacement parts.
p
ROTEL
e

4RA-04SE Stereo Integrated Amplifier
Figure 2: Preamp Input and Speaker Output Connections
Signaux d’entrée et branchements enceintes acoustiques
Anschlussdiagramm
Conexiones para Entrada de Señal y Salida a las Cajas Acústicas
De signaalingangen en de luidsprekeruitgangen
Collegamenti ingresso preamp ed uscita per diffusori
Anslutningar för förförstärkare och högtalare
èÓ‰ÒÓ‰ËÌÂÌË ËÒÚÓ˜ÌËÍÓ‚ Ò˄̇· Ë ‡ÍÛÒÚ˘ÂÒÍËı ÒËÒÚÂÏ
RIGHT
INTEGRATED AMPLIFIER
MODEL NO. RA-04SE
POWER CONSUMPTION : 220W
SERIAL NO. RP-502
SPEAKER B
LEFTRIGHT
CLASS 2 WIRING
LEFTRIGHT
SPEAKER A
12V TRIGGER OUT
SPEAKER IMPEDANCE
A OR B - 40HMS MINIMUM
A AND B - 80HMS MININUM
PRE OUTTAPEAU X 2AU X 1TUNERCDPHONO
IN OUT
LEFT
GND
WARNING: TO REDUCE THE RISK OF THE FIRE OR ELECTRICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
DOUBLE INSULATION
When servicing
use only identical replacement parts.
ROTEL
RIGHT
Warning: Turn off this unit and the entire system
before making connections!
Attention: éteignez cet appareil et le système
complet avant d’effectuer le moindre
branchement !!
Warnung: Schalten Sie dieses Gerät und das
gesamte System vor dem Anschließen
ab!
Attenzione: Spegnete l’unità e l’intero sistema
prima di effettuare le connessioni!
¡Advertencia! Antes de realizar cualquier tipo de
conexión, desactive este aparato y
el resto del equipo.
Waarschuwing: Schakel dit apparaat en het gehele
systeem uit voordat u verbindingen
maakt!
Varning: Stäng av denna enhet samt hela
systemet innan anslutningar utförs!
Предупреждение: Выключите устройство и всю систему
перед соединением!
INTEGRATED AMPLIFIER
MODEL NO. RA-05SE
POWER CONSUMPTION : 220W
SERIAL NO. RP-503
SPEAKER B
LEFTRIGHT
CLASS 2 WIRING
LEFTRIGHT
SPEAKER A
12V TRIGGER OUT
IR
OUT
EXT REM
IN
SPEAKER IMPEDANCE
A OR B - 40HMS MINIMUM
A AND B - 80HMS MININUM
PRE OUTTAPEAU X 2AU X 1TUNERCDPHONO
IN OUT
LEFT
GND
WARNING: TO REDUCE THE RISK OF THE FIRE OR ELECTRICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
DOUBLE INSULATION
When servicing
use only identical replacement parts.
ROTEL

5
English
About Rotel
Our story began nearly 50 years ago. Over the decades, we have
received hundreds of awards for our products and satisfied hundreds
of thousands of people who take their entertainment seriously – like
you!
Rotel was founded by a family whose passionate interest in music
led them to manufacture high-fidelity components of uncompromising
quality.
Through the years, that passion has remained undiminished and the
family goal of providing exceptional value for audiophiles and music
lovers, regardless of their budget, is shared by all Rotel employees.
Rotel’s engineers work as a close team, listening to, and fine tuning,
each new product until it reaches their exacting musical standards.
They are free to choose components from around the world in
order to make that product the best they can. You are likely to find
capacitors from the United Kingdom and Germany, semiconductors
from Japan or the United States, while toroidal power transformers
are manufactured in Rotel’s own factory.
We all have concerns about our environment. And, as more and more
electronics are produced and later discarded, it is especially important
for a manufacturer to do all it can to engineer products that have a
minimum negative impact on landfill sites and water tables.
At Rotel, we are proud to do our part. We have reduced the lead
content in our electronics by using special ROHS solder, while our
new Class D (not digital) amplifiers are up to five times more efficient
than our legacy designs and still deliver power and performance.
These products run cool, give minimum wasted energy, are good for
the environment and give better sound too.
Finally, we have printed this brochure on recycled paper stock.
While we understand that these are small first steps, they are still
important ones. And we continue to pursue new methods and materials
for a cleaner and greener manufacturing process.
All of us at Rotel thank you for buying this product. We are sure it
will bring you many years of enjoyment.
Contents
Figure1:ControlsandConnections................................... 3
Figure 2: Signal Input and Speaker Output Connection.......................... 4
About Rotel ....................................................5
GettingStarted.................................................6
A Few Precautions 6
Placement 6
Cables 6
AC Power and Control ............................................6
AC Power Input o6
Power Switch 2and Power Indicator 16
Input Signal Connections...........................................7
Phono Input eand Ground Connection w7
Line Level Inputs r7
Recorder Connections t..........................................7
Preamp Outputs y.............................................7
Speaker Outputs ui Speaker Selector Switch 6.....................7
Speaker Selection 7
Speaker Wire Selection 7
Polarity and Phasing 7
Speaker Connection 7
Phones Output 4..............................................8
Media Player 5...............................................8
Audio Controls ..................................................8
Volume Control 08
Balance Control -8
Tone On/Off Switch 98
Bass and Treble Controls 788
Function Control q9
Montion Control =9
12 Volt Trigger Outlet p.........................................8
Protection Indicator 3....................................................9
Troubleshooting................................................. 9
Power Indicator Is Not Lit 9
Fuse Replacement 9
No Sound 9
Specifications................................................... 9

6RA-04SE Stereo Integrated Amplifier
Getting Started
Thank you for purchasing the Rotel RA-04 SE Stereo Integrated Amplifier.
When used in a high-quality music audio system, it will provide years
of musical enjoyment.
The RA-04 SE is a full featured, high performance component. All aspects
of the design have been optimized to retain the full dynamic range and
subtle nuances of your music. The RA-04 SE has a highly regulated power
supply incorporating a Rotel custom-designed toroidal power transformer.
This low impedance power supply has ample power reserves, which
enables the RA-04 SE to easily reproduce the most demanding audio
signals. This type of design is more expensive to manufacture, but it is
better for the music.
The printed circuit boards (PCB) are designed with Symmetrical Circuit
Traces. This insures that the precise timing of the music is maintained
and faithfully recreated. The RA-04 SE circuitry uses metal film resistors
and polystyrene or polypropylene capacitors in important signal paths.
All aspects of this design have been examined to ensure the most faithful
music reproduction.
The main functions of the RA-04 SE are easy to install and use. If you
have experience with other stereo systems, you shouldn’t find anything
perplexing. Simply plug in the associated components and enjoy.
A Few Precautions
WARNING: To avoid potential damage to your system, turn off ALL
the components in the system when connecting or disconnecting the
loudspeakers or any associated components. Do not turn the system
components back on until you are sure all the connections are correct
and secure. Pay particular attention to the speaker wires. There must
be no loose strands that could contact the other speaker wires, or the
chassis of the amplifier.
Please read this manual carefully. It provides information on how to
incorporate the RA-04 SE into your system as well as information that will
help you get optimum sound performance. Please contact your authorized
Rotel dealer for answers to any questions you might have. In addition,
all of us at Rotel welcome your questions and comments.
Save the RA-04 SE shipping carton and all enclosed packing material
for future use. Shippingor moving the RA-04 SE in anything other than
the original packing material may result in severe damage to your
amplifier.
Fill out and send in the owner’s registration card packed with the RA-04
SE. Also be sure to keep the original sales receipt. It is your best record
of the date of purchase, which you will need in the event warranty
service is ever required.
Placement
Like all audio components that handle low level signals, the RA-04 SE can
be affected by its environment. Avoid placing the RA-04 SE on top of other
components. Also avoid routing audio signal cables near power cords.
This will minimize the chance it will pick up hum or interference.
The RA-04 SE generates heat as part of its normal operation. The heat
sinks and ventilation openings in the amplifier are designed to dissipate
this heat. The ventilation slots in the top cover must be open. There should
be 10 cm (4 inches) of clearance around the chassis, and reasonable
airflow through the installation location, to prevent the amplifier from
overheating.
Remember the weight of the amplifier when you select an installation
location. Make sure that the shelf or cabinet can support it. We
recommend installing the RA-04 SE in furniture designed to house audio
components. Such furniture is designed to reduce or suppress vibration
which can adversely affect sound quality. Ask your authorized Rotel
dealer for advice about component furniture and proper installation of
audio components.
Cables
Be sure to keep the power cords, digital signal cables and regular
audio signal cables in your installation away from each other. This will
minimize the chance of the regular audio signal cables picking up noise
or interference from the power cords or digital cables. Using only high
quality, shielded cables will also help to prevent noise or interference from
degrading the sound quality of your system. If you have any questions
see your authorized Rotel dealer for advice about the best cable to use
with your system.
AC Power and Control
AC Power Input o
The RA-04 SE does not draw high levels of current from the power outlet.
However, whenever possible, it should be plugged directly into a 2-pin
polarized wall outlet. Do not use an extension cord. A heavy duty multi-
tap power outlet strip may be used if it (and the wall outlet) can handle
the current demanded by the RA-04 SE and all the other components
connected to it.
Your RA-04 SE is configured at the factory for the proper AC line voltage
in the country where you purchased it (either 120 volts AC or 230
volts AC with a line frequency of either 50 Hz or 60 Hz). The AC line
configuration is noted on a decal on the back panel.
NOTE: Should you move your RA-04 SE amplifier to another country,
it is possible to reconfigure it for use on a different line voltage. Do not
attempt to perform this conversion yourself. Opening the enclosure of the
RA-04 SE exposes you to dangerous voltages. Consult a qualified service
person or the Rotel factory service department for information.
If you are going to be away from home for an extended period of time
such as a month-long vacation, it is a sensible precaution to unplug your
amplifier (as well as other audio and video components) while you are
away.
Power Switch 2and Power Indicator 1
Press the front panel Power Switch button, to turn the RA-04 SE on. The
Power Indicator light is illuminated when the RA-04 SE is on. Press Power
Switch button again to turn the RA-04 SE off.
See the “12V Trigger Outlet” section for more information on ways you
may be able to turn on and off other components in your system along
with the RA-04 SE.

7
English
Input Signal Connections
[See Figure 2.]
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.
Phono Input eand Ground Connection w
Plug the cable from the turntable into the appropriate left and right phono
inputs. If the turntable has a “ground” wire, connect it to the screw terminal
to the left of the Phono inputs. It will help prevent hum and noise.
Line Level Inputs r
The CD, Tuner, and Aux inputs of the RA-04 SE are “line level” inputs.
These are for connecting components such as CD players, Hi Fi or NICAM
Stereo video cassette recorders, tuners, Laser Disc players or the analog
output from a CD-ROM drive.
The Left and Right channels are labeled and should be connected to the
corresponding channels of the source component. The Left connectors
are white, the Right connectors are red. Use high quality RCA cables for
connecting input source components to the RA-04 SE. Ask your authorized
Rotel dealer for advice about cables.
Recorder Connections t
[See Figure 2.]
The Tape inputs and outputs can be connected to any record playback
device that accepts standard line level analog input and output signals.
Typically that will be a conventional tape recorder.
When connecting a recorder to the RA-04 SE remember that the outputs
of the recorder must be connected to the tape inputs of the RA-04 SE.
Similarly the tape outputs of the RA-04 SE must be connected to the
inputs of the recorder. As with other sources be sure to connect the
Left and Right channels of each device to the proper channels on the
associated components. Use high quality connecting cables to prevent
loss of sound quality.
NOTE: The Tape Outputs are not affected by the Volume, Balance or
Tone controls. They receive a fixed level signal.
Preamp Outputs y
The RA-04 SE has a set of preamp outputs. The signal from the source
selected with the Function Selector is always available from these outputs.
Typically these outputs are used to provide a signal to another integrated
amplifier or power amplifier, which is used to drive remote speakers
NOTE: Changes to the settings of the Volume, Balance or Tone controls
affect the signal from the Preamp Outputs.
Speaker Outputs ui
Speaker Selector Switch 6
[See Figure 2.]
The RA-04 SE has two sets of speaker outputs, labeled “A” uand “B”
i.The speaker outputs are controlled by the switch 6 on the front
panel.
Speaker Selection
If only one set of speakers will be used at any given time, the speakers may
have an impedance as low as 4 ohms. If there are times when both the A
and B speakers will be used, all the speakers should have an impedance
of 8 ohms or more. Speaker impedance ratings are less than precise. In
practice, very few loudspeakers will present any problems for the RA-04
SE. See your authorized Rotel dealer if you have any questions.
Speaker Wire Selection
Use insulated two-conductor stranded wire to connect the RA-04 SE to
the speakers. The size and quality of the wire can have an audible effect
on the performance of the system. Standard speaker wire will work, but
can result in lower output or diminished bass response, particularly over
longer distances. In general, heavier wire will improve the sound. For
best performance, you may want to consider special high-quality speaker
cables.Your authorized Rotel dealer can help in the selection of cables
for your system.
Polarity and Phasing
The polarity – the positive/negative orientation of the connections – for
every speaker and amplifier connection must be consistent so all the
speakers will be in phase. If the polarity of one connection is reversed,
bass output will be very weak and stereo imaging degraded. All wire
is marked so you can identify the two conductors. There may be ribs
or a stripe on the insulation of one conductor. The wire may have clear
insulation with different color conductors (copper and silver). There may
be polarity indications printed on the insulation. Identify the positive and
negative conductors and be consistent with every speaker and amplifier
connection.
Speaker Connection
Turn off all the components in the system before connecting the speakers.
The RA-04 SE has color-coded binding post type speaker connectors on
the back panel (except in European Community countries where their use
is not permitted). These connectors accept bare wire, connector lugs, or
dual banana type connectors.
Route the wire from the RA-04 SE to the speakers. Give yourself enough
slack so you can move the components to allow access to the speaker
connectors. If you are using dual banana plugs, connect them to the wires
and then plug into the backs of the binding posts. The thumbscrews of the
binding posts should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are attaching
bare wires directly to the binding posts, separate the wire conductors
and strip the insulation from the end of each conductor. Be careful not
to cut into the wire strands. Unscrew (turn counterclockwise) the binding
post thumbscrews. Place the connector lug or wire around the binding
post shaft. Turn the thumbscrews clockwise to clamp the connector lug
or wire firmly in place.

8RA-04SE Stereo Integrated Amplifier
NOTE: Be sure there are no loose wire strands that could touch adjacent
wires or connectors.
Phones Output 4
The Phones output allows you to connect headphones for private listening.
This output accommodates standard stereo phone (1/8”) plugs. Plugging
in a set of headphones does not cut off the signal to the outputs. Use the
Speaker Selector to turn off the speakers. The settings of the Function
Selector and the Tape Monitor Control determines which source is heard.
To listen to or monitor the component connected to the Tape input set
the Monitor Control to the Tape position. For all other inputs leave the
Monitor Control in the Source position and select the source you want to
listen to with the front panel Function Selector or press the corresponding
source button on the remote control.
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.
Media Player 5
A 3.5mm (1/8”) stereo input socket for a “Media Player” is provided on
the front of the amplifier and is selected by setting the function control
to (AUX2). Any portable stereo cassette, compact disc player or hard
disc playback device can be connected via this input. If the device you
are connecting has its output via the headphone socket then note that
you must adjust the volume control on the player for sound to be heard.
Should the sound be loud and distorted turn down the volume on the
player and if it is only just audible through the speakers even when the
amplifier volume control is turned up fairly high then adjust the volume
control on the player.
NOTE: When the 3.5mm (mimi jack) is inserted into the Media Player
socket the rear input called AUX2 is disconnected. Removing the 3.5mm
plug from the Media player socket will allow the rear AUX2 input to
function.
Audio Controls
Volume Control 0
Turn the controls clockwise to increase the volume, or counter clockwise
to decrease the volume.
Balance Control -
The Balance Control adjusts the left-to-right balance of the sound output.
Normally the control should be left in the center position. In some situations,
typically when the main listening position is not ideally centered between
the speakers, it may be necessary to adjust the control to achieve proper
left-to-right balance. Turning the control counter-clockwise shifts the sound
balance to the left. Turning the control clockwise shifts the sound balance
to the right.
Tone On/Off Switch 9
When the Tone Switch is in the Off position the Bass and Treble Control
(Tone Control) circuits are bypassed to ensure the purest possible sound.
Leave the Tone Switch in the Off position unless you want to use the Tone
Controls. Turn the Tone Switch to the On position if you want to adjust
the Tone Controls.
Bass and Treble Controls 78
When the Tone Switch is in the On position, turning the Bass and Treble
Controls adjusts the tone balance of the sound. Turn the Controls clockwise
to increase the bass or treble output. Turn the Controls counterclockwise
to decrease the bass or treble output.
A properly setup high-performance audio system produces the most
natural sound with little or no adjustment of the tone controls. Use these
controls sparingly. Be particularly careful when turning the controls up
(clockwise). This increases the power output in the bass or treble range,
increasing the load on the amplifie and speakers.
Function Control q
The Function control selects the input signal source. The signal selected
by the Function control is the one you hear, as long as the Monitor
control is set to the Source postion. (See the following section.) The signal
selected by the Function control also goes to Preamp Outputs and the
Tape Outputs. Turn the front panel Listening Selector to the source you
want to listen to.
Montion Control =
When the Monitor Control is set to the Source position, the signal you
hear, and which goes to the Preamp Outputs, is selected by the Function
Control. To listen to the signal from a recorder connected to the Tape
Inputs, set the Monitor Control to the Tape position. When the Monitor
Control is in the Tape position, the signal from the Tape Input also goes
to the Preamp Outputs.
The signal that goes to the Tape Output is always selected by the
Function Control. When you are recording with a unit that has monitoring
capabilities, you can listen to the sound just recorded by setting the
Monitor Control to the Tape position.
12V Trigger Outlet p
Some audio components can be turned on automatically when they
receive a 12V turn on “signal”. The two12V Trigger Outputs of the RA-04
SE provide the required signal. Connect compatible components to the
RA-04 SE with a conventional 3.5mm miniplug cable. When the RA-04
SE is in turn off mode, the trigger signal is interupted, so the components
controlled by it are turned off.

9
English
Protection Indicator 3
The RA-04 SE has both thermal and over-current protection circuitry that
protects the amplifier against damage in the event of extreme or faulty
operating conditions. The protection circuits are independent of the audio
signal and have no impact on sonic performance. Instead, the protection
circuits monitor the temperature of the output devices and shut down the
amplifier if temperatures exceed safe limits.
Most likely, you will never see this protection circuitry in action. However,
should a faulty condition arise, the amplifier will stop playing and the
LED indicator on the front panel will light up.
If this happens, turn the amplifier off. Let it cool down for several minutes,
and attempt to identify and correct the problem that caused the protection
circuitry to engage. When you turn the amplifier back on, the protection
circuit will automatically reset and the indicator LED should go out.
In most cases, the protection circuitry activates because of a fault condition
such as shorted speaker wires, or inadequate ventilation leading to an
overheating condition. In very rare cases, highly reactive or extremely low
impedance speaker loads could cause the protection circuit to engage.
If the protection circuitry triggers repeatedly and you are unable to isolate
and correct the faulty condition, contact your authorized Rotel dealer for
assistance in troubleshooting.
Troubleshooting
Most difficulties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difficulty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from the
RA-04 SE, refer to the suggestions for the following conditions:
Power Indicator Is Not Lit
The Power Indicator and the basic items in the Display window should be
lit whenever the RA-04 SE is plugged into the wall power outlet and the
Power button is pushed in.If it does not light, test the power outlet with
another electrical device,such as a lamp. Be sure the power outlet being
used is not controlled by a switch that has been turned off.
Fuse Replacement
If another electrical device works when plugged into the power outlet,
but the Power Indicator of the RA-04 SE does not light when plugged into
the same outlet and the Power Switch is pushed in, it indicates that the
internal power fuse may have blown. If you believe this has happened,
contact your authorized Rotel dealer to get the fuse replaced.
No Sound
Check the signal source to see if it is functioning properly. Make sure
the cables from the signal source to the RA-04 SE inputs are connected
properly. Be sure the Listening Selector is set to the proper input. Check
the wiring between the RA-04 SE and the speakers.
Specifications
Continuous Power Output 40 watts/ch
(20-20 kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power,
1/2 power or 1 watt
Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power,
1/2 power or 1 watt
Frequency Response
Phone input 20Hz-15kHz, ±0.3dB
Line Level Inputs 10Hz-40kHz, ±1dB
Damping Factor (20-20,000 Hz, 8 ohms) 180
Input Sensitivity / Impedance
Phone input 2.5mV / 47 kOhms
Line Level Inputs 150 mV / 24 kOhms
Input Overload
Phone input 180mV
Line Level Inputs 5V
Premp Output / Impedance 1V / 470 Ohms
Tone Controls - Bass / Treble ±6 dB at 100Hz / 10kHz
Signal to Noise Ratio (IHF “A” weighted)
Phone input 80 dB
Line Level Inputs 100 dB
Power Requirements 230 Volts, 50 Hz
Power Consumption 220 Watts
Dimensions (W, H, D) 171/8” x 27/8” x 131/2”
435 x 72 x 342 mm
Panel Height 60 mm / 23/8”
Weight (net) 5.9 kg, 13lbs
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel HiFi logo are registered trademarks of
The Rotel Co, Ltd., Tokyo, Japan.

10 RA-04 SE Amplificateur intégré stéréophonique
La prise d’alimentation secteur constitue le moyen radical de
déconnexion de l’appareil. Elle doit donc rester en permanence
accessible, car sa déconnexion constitue la seule assurance que
l’appareil n’est plus alimenté par le secteur. La diode LED de mise
enveilleStandbynes’allumepluslorsquece cordond’alimentation
est débranché.
Prendre garde à ce que ce cordon d’alimentation ne soit pas pincé,
écrasé ou détérioré sur tout son trajet, et à ce qu’il ne soit pas mis
en contact avec une source de chaleur. Vérifiez soigneusement la
bonne qualité des contacts, à l’arrière de l’appareil comme dans
la prise murale.
Prendre garde à ce que ce cordon d’alimentation ne soit pas pincé,
écrasé ou détérioré sur tout son trajet, et à ce qu’il ne soit pas mis
en contact avec une source de chaleur. Vérifiez soigneusement la
bonne qualité des contacts, à l’arrière de l’appareil comme dans
la prise murale.
Débranchez le câble d’alimentation en cas d’orage, ou si l’appareil
ne doit pas être utilisé pendant une longue période.
N’utilisez que des accessoires préconisés par le constructeur.
N’utilisez que des meubles, supports, systèmes de transport
recommandés par Rotel. Procédez toujours avec la plus extrême
précaution lorsque vous déplacez l’appareil, afin d’éviter tout
risque de blessure.
L’appareildoitêtreimmédiatementéteint, débranchépuis retourné
au service après-vente agréé dans les cas suivants :
• Lecâbled’alimentationsecteurousapriseestendommagé.
• Unobjetesttombé,ouduliquideacouléàl’intérieurde
l’appareil.
• L’appareilaétéexposéàlapluie.
• L’appareilnefonctionnemanifestementpasnormalement.
• L’appareilesttombé,oulecoffretestendommagé.
Utilisez un câble de type Classe 2 pour la liaison avec les enceintes
acoustiques,afindegarantiruneinstallationcorrecteetdeminimiser
les risques d’électrocution.
ATTENTION : Il n’y a à l’intérieur aucune pièce susceptible
d’être modifiée par l’utilisateur. Adressez-vous impérativement
à une personne qualifiée.
ATTENTION : Pourréduiretoutrisqued’électrisationoud’incendie,
ne pas exposer l’appareil à une source humide, ou à tout type
de risque d’éclaboussure ou de renversement de liquide. Ne
pas poser dessus d’objet contenant un liquide, comme un verre,
un vase, etc. Prenez garde à ce qu’aucun objet ou liquide ne
tombe à l’intérieur de l’appareil par ses orifices de ventilation. Si
l’appareilest exposéà l’humiditéou si un objet tombeàl’intérieur,
débranchez-le immédiatement de son alimentation secteur, et
adressez-vous immédiatement et uniquement à une personne
qualifiée et agréée.
Tous les conseils de sécurité et d’installation doivent être lus avant
de faire fonctionner l’appareil. Conservez soigneusement ce livret
pour le consulter à nouveau pour de futures références.
Tous les conseils de sécurité doivent être soigneusement respectés.
Suivez les instructions. Respectez les procédures d’installation et
de fonctionnement indiquées dans ce manuel.
L’appareil doit être nettoyé uniquement avec un chiffon sec ou
un aspirateur.
L’appareil doit être placé de telle manière que sa propre
ventilation puisse fonctionner, c’est-à-dire avec un
espace libre d’une dizaine de centimètres minimum
autour de lui.
Il ne doit pas être posé sur un fauteuil, un canapé, une couverture
ou toute autre surface susceptible de boucher ses ouïes d’aération ;
ou placé dans un meuble empêchant la bonne circulation d’air
autour des orifices d’aération.
Cet appareil doit être placé loin de toute source de chaleur, tels que
radiateurs,chaudières,bouchesde chaleurou d’autresappareils (y
compris amplificateurs de puissance) produisant de la chaleur.
Cet appareil doit être branché sur une prise d’alimentation
secteur, d’une tension et d’un type conformes à ceux qui sont
indiqués sur la face arrière de l’appareil (USA : 120 V/60 Hz,
CE : 230 V/50 Hz)
Brancher l’appareil uniquement grâce au cordon secteur fourni,
ou à un modèle équivalent. Ne pas tenter de modifier ou changer
la prise. Notamment, ne pas tenter de supprimer la prise de
terre (troisième broche de la prise) si celle-ci est présente. Si la
prise n’est pas conforme à celles utilisées dans votre installation
électrique, consultez un électricien agréé. Ne pas utiliser de
cordon rallonge.
Tous les appareils Rotel sont conçus en totale
conformité avec les directives internationales
concernantlesrestrictionsd’utilisationdesubstances
dangereuses(RoHS)pourl’environnement,dansles
équipements électriques et électroniques, ainsi que
pourlerecyclagedesmatériauxutilisés(WEEE,pour
Waste Electrical and Electronic Equipment).
Instructions importantes concernant la sécurité
Ce symbole signifie que cet appareil bénéficie d’une
double isolation électrique. Sa prise d’alimentation
n’a pas besoin d’être reliée à la terre ou à une
masse particulière.
Le symbole du conteneur à ordures barré par une
croix indique la compatibilité avec ces directives, et
le fait que les appareils peuvent être correctement
recyclés ou traités dans le respect total de ces
normes.
ATTENTION :
RISQUE D’ÉLECTROCUTION.
NE PAS OUVRIR
ATTENTION : POUR RÉDUIRE LE RISQUE D’ÉLECTROCUTION, NE PA S
RETIRER LE CAPOT. IL N’Y A À L’INTÉRIEUR AUCUNE PIÈCE
SUSCEPTIBLE D'ÊTRE MODIFIÉE PA R L’UTILISATEUR. EN CAS DE
PROBLÈME, ADRESSEZ-VOUS À UN RÉPARATEUR AGRÉÉ.
L’ éclair dans un triangle équilatéral indique
la présence interne de tensions électriques
élevées susceptibles de présenter des
risques graves d’électrocution.
Le point d’exclamation dans un triangle
équilatéral indique à l’utilisateur la
présence de conseils et d’informations
importantes dans le manuel d’utilisation
accompagnant l’appareil. Leur lecture est
impérative.