Rowlinson Playaway house User manual

Playaway House English SS190B

Assembly Instructions

30 32

Before assembly

•We recommend that time is taken to read the

instructions before starting assembly, then follow

the easy step by step guide.

•The instruction sheet is only a guide to the

assembly. Certain items may not be shown to scale.

•Check all components prior to assembly

•This product should be assembled by no less than

two people.

•Never attempt to erect the assembly in high winds.

•Drill components where indicated.

x 2 Drill

No. Components Qty.

1Floor 1

2Side panel 1

3Back panel 1

4Window side panel 1

5Front panel 1

6Apex panel 2

7Roof purlin (28 x 28 x 1178mm) 1

8Roof panel (8 x 915 x 1220mm) 2

9Roof panel (8 x 915 x 280mm) 2

10 Felt batten (28 x 28 x 1500mm) 2

11 Roofing felt (4m) 1

12 Bargeboard 4

13 Roof block 4

14 Corner coverstrip 4

15 Veranda floor 1

16 Veranda fence 2

17 Veranda roof support 2

18 Door 1

19 Front window (650 x 590mm) 1

20 Side window (550 x 470mm) 1

21 Perspex for door (520 x 545mm) 1

22 Perspex for front window (575 x 520mm) 1

23 Perspex for side window (478 x 398mm) 1

24 Door beading (10 x 10 x 545mm) 2

25 Door beading (10 x 10 x 503mm) 2

26 Window beading (10 x 10 x 580mm 2

27 Window beading (10 x 10 x 503mm) 2

28 Window beading (10 x 10 x 479mm) 2

29 Window beading (10 x 10 x 380mm) 2

30 Door hinge 1

No. Fixing Kit Qty.

31 Finials 2

32 Door handle 1

33 Magnetic catch 1

34 50mm screws 40

35 32mm screws 8

36 25mm screws 21

37 19mm round head screws 2

38 19mm black round head screws 4

39 12mm screws 2

40 30mm nails 78

41 20mm nails 36

42 10mm felt nails 70

Recommended tools for assembly

•Cordless drill/screwdriver

•Drill with 2mm drill bit

•Hammer

•Spirit level

•Sharp knife

•Silicon sealant

IMPORTANT SAFETY

INFORMATION

Adult assembly is required. Checks and

maintenance needs to be carried out on

the main parts (fixings etc.) at regular

intervals. If these checks are not carried

out the product could become unsafe.

WARNING

Not suitable for children under

36 months due to small parts

and sharp points.

For family domestic use only.

For outdoor use.

Dimensions

Overall external

Height = 1620mm

Width = 1600mm

Depth = 1565mm

Footprint

Width = 1468mm

Depth = 1455mm

Min. base area

Width = 1518mm

Depth = 1505mm

25mm

Small tab

to door.

Large tab to Front

panel frame.

Front panel

32mm

19mm

50mm

Back panel

Side panel

Panel frames

rest on floor.

Panel cladding

overhangs floor

edge.

Back panel

Front panel

Side panel

Drill

Drill pilot

holes for the

window

screws.

2. Door panel

Attach the three small tabs of the hinge to the door as shown using 2 x 25mm screws per tab. Open the hinge and secure the large tab to the door frame using 5 x 25mm

screws per tab as shown below. Put the window into place on the front panel, Secure into place using 4 x 32mm. Screw through the side of the window frame into the

framework of the front panel. Secure the door handle using 4 x 19mm black roundhead screws as shown below.The magnetic catch is fitted to the front panel framing

just inside the door, the catch plate is fitted to the door. Position them so that when the door is shut the two parts clip together. Once in position fix the magnetic catch

to the panel frame using 2 x 19mm round head screws and the catch plate to the inside of the door using 2 x 12mm screws.

4.Walls to floor

Ensure the panels are sitting square on the floor. Secure using 2 x 50mm screws per panel, screw through the panel frame, through the floor and into the floor bearers.

50mm

50mm 50mm

Floor bearers

Floor

Panel frames

Side panel Back panel

3.Wall panels

Position the back panel and the side panel as shown. Note how the panel frames sit on the floor with the panel cladding overhanging the floor edge. Ensure square and secure

using 2 x 50mm screws through the frame of the side panel into the frame of the back panel. Fit the side window frame into the window side panel using 4x32mm screws

secure in the same way as the front window in the front panel. Continue by attaching the window side panel to the back panel and then add the door panel in the same way.

Drill

Drill pilot holes for

these screws.

Door

Front panel

19mm

12mm

1. Floor section

Prepare a level area for the playhouse to sit.Attach four treated wooden or similar bearers of size 50 x 50 x 1468mm to the floor (Not supplied in kit).Attach two treated

wooden or similar bearers of size 50 x 50 x 1473mm to the bottom of the veranda floor (Not supplied in kit).

To " VALIDATE" the guarantee, this item should be erected on

50mm x 50mm treated wooden or similar bearers (These are

not supplied with the kit.) Ground contact must be avoided.

The side window is fitted

and secured in the same

way as the front window is

fitted to the front panel.

50mm

Drill

Drill pilot holes for

these screws.

50mm

30mm

Felt batten

Length 1500mm

Felt batten

6. Roof

Insert the roof purlin into the rebate at the top of the apex panels, secure in place using 2 x 50mm screws. Screw in through the apex cladding into the ends of the purlin.

Secure to each felt batten one large roof panel and one small roof panel using 9 x 30mm nails as shown. Ensure the felt batten is flush to the edges of the panels. Flush to

the front edge of each roof section attach two roof blocks using 2 x 30mm nails per block nail through the roof into the block. Position the roof panels onto the assembly,

make sure the top edges are located at the apex and the roof is flush with the back apex. Secure with 12 x 30mm nails per roof section, nail through the roof and into

the top frames of the building.

Felt batten

5.Apex panels

Place an apex panel on top of the back panel, make sure the shiplap cladding of the apex fits correctly into the shiplap cladding of the back panel. Secure in place using

3 x 50mm screws. Screw up through the top frame of the back panel into the bottom frame of the apex.Attach the remaining apex to the front panel in the same way.

Roof

7.Veranda fence

Fit a coverstrip in each corner, secure in place using 3 x 30mm nails per strip. Position the veranda floor up against the front of the playhouse. Sit the veranda fences on

the floor and attach to the front wall of the building using 2 x 50mm and attach to the veranda floor using 2 x 50mm screws. For the veranda roof supports, position one

at the end of each veranda fence. Ensure the angle of the support is the same as the roof. Attach the support to the fences and floor using 3 x 50mm screws per support

as shown. Secure the top of each support by screwing 1 x 50mm screw through the roof into the end of the support.

30mm

Roof

30mm

50mm

Felt batten

Length 1500mm

Ensure the top

edge of each roof

panel is located at

the apex.

Front edge

Left-hand roof section Right-hand roof section

455mm

25mm

Roof blocks

Felt batten Felt batten

Roof purlin Length 1178mm

30mm30mm

50mm

Drill

Drill pilot holes for all

screws in this section

When attaching the veranda fence to the

front of building, drill and screw at a slight

angle to allow drill/driver access. Ensure

the screws tips do not come through to

the inside of the playhouse.

Window frame

Window pane

Wooden beading

20mm

9. Glazing

It is recommended that a waterproof sealant is applied around the edge of the glazing before fitting. For each window and door, place a perspex pane on the inside of the

window frame, nail the wooden beading strips into position using 3 x 20mm nails per strip.

Window pane

8. Roof felt

Cut the roof felt roll into two equal pieces. Place one piece of felt over one side of the roof.Along the front, back and lower edge leave an overhang of felt of at least 40mm.

Fold down the felt along the lower edge and secure to the felt batten using 18 x 10mm felt nails evenly spaced.Tension the felt over the roof ridge and secure along the

opposite edge using 4 x 10mm felt nails. position the second piece of felt in the same way as the first on the other side of the roof.Attach to the felt batten using 18 x 10mm

felt nails, tension over the roof and secure with 18 x 10mm felt nails.At the front dress down the felt and secure to the roof blocks and felt batten using 6 x 10mm felt nails.

Repeat at the back securing the felt to the apex panel. Using a sharp knife trim off excess felt. Secure two bargeboards at the front, ensure that the top edges are flush with

the roof line and the boards meet evenly at the apex secure using 3 x 30mm nails per board. Nail to the roof blocks and the veranda roof support.Attach a finial centrally

over the join between the two bargeboards using 2 x 30mm nails. Repeat for bargeboards and finials on the back.

10mm

Felt

nails 10mm

Felt

nails

10mm

Felt

nails

10mm

Felt

nails 30mm

30mm

Attach 2 coverstrips and finial on the

back of the building in the same way.

Important safety and maintenance information - Retain for future reference

•This product is not suitable for all children under 36 months, due to it having small parts and sharp points.

•For Family domestic use only.

•For outdoor use.

•Ensure any loose knots are removed from any panels, to reduce risk of choking. Fill holes with a suitable wood filler obtained from most DIY stores.

•It is recommended that the playhouse is positioned on a level surface at least 2m from any structure or obstruction such as a fence, garage, house, overhanging

branches, laundry lines, electrical wires.

•It is recommended that the playhouse is not installed on concrete, asphalt or any other hard surface.

•The company takes every care to ensure all goods are clean and free from splinters and rough edges prior to leaving the factory.

•Visually inspect the playhouse and to reduce the risk of splinter sand down any sharp edges or rough surfaces.

•Checks and maintenance of the main parts (fixings, etc) should be made at the beginning of each season and at regular intervals throughout. If checks are not carried

out the product could become unsafe.

•Ensure all fastenings are securely located.

•Oil all metallic moving parts.

•Ensure that the pointed ends of all nails, screws and other fastenings are not accessible on any surface of the constructed playhouse, and that all heads and surfaces

of these fastenings are either flush with the surface or countersunk.

•Always ensure a safe, suitable treatment is used to ensure the safety of children and animals.

•Assembly and installation instructions must be kept for further reference.

Shiplap buildings come ready stained but this is only a preparatory treatment.To VALIDATE the guarantee, the building must be properly treated with a recognised

external wood preserver WITHIN 3 MONTHS of assembly and RE-TREATED ANNUALLY thereafter.The building must also be erected on 50mm x 50mm treated

wooden or similar bearers (These are not supplied with the kit.) Ground contact must be avoided.

Timber Information.

As timber is a natural material, there are certain weather conditions that may affect the materials properties. In times of excessive dry spells the material may lose some

of its internal moisture causing a certain degree of shrinkage on a panel and in periods of excessive rain there will be a certain amount of swelling throughout the wooden

panels.This process can not be avoided. If you have problems with certain boards shrinking in dry spells try to decrease the amount of direct sunlight on the building or