RunCam New Swift 2 User manual

RunCam Swift 2
USER MANUAL

Connection
UP
UP
DOWN
DOWN
L R
Transmitter
5D-OSD menu cable
2 pin extension cord
Power in
GND
To VBAT+
* Unplug the 5D-OSD menu cable after OSD setting.
5-36V in
GND
Video out
Audio out
VBAT+
5-36V

1Nylon Gaskets 2M2*4 Screws
3M3*5 Screws 4M3 Non-slip Nuts
26mm
28.5mm
26mm
1 1
11
44
2
2
2
33
2
Dimensions & Installation
5-36V

OSD Menu
OSD Setting: Press and hold the UP button for 2 seconds to enter OSD setup menu.
·
·
PILOT: ON/OFF
Customize the PILOT name: Use the UP,
DOWN, LEFT and RIGHT buttons to
navigate through the letters and
confirm with the CENTER button.
Quick settings:
Long press the LEFT/DOWN/RIGHT
button for 2 seconds to activate the
VOLTAGE/PILOT/TIMER, then you can use
the UP, DOWN, LEFT and RIGHT buttons
to move it to the appropriate location on
the screen, and press the CENTER button
to exit.
RunCam
ON
ON
ON
OFF
VOLTAGE
PILOT
TIMER
EXIT
BASELINE
DEFAULT
1234567890ABCDEFG
HIJKLMNOPQRSTUVWX
YZabcdefghijklmno
pqrstuvwxyz.-:/@
The OSD displays by default the input
voltageof the camera. If the VBAT + cable
is connected to the battery's positive side,
it displays the battery voltage instead.
·
·
EXIT: Save the current settings and exit
·
·
BASELINE: OFF/1-9
·
·
VOLTAGE: ON/OFF
·
·
TIMER: ON/OFF

OSD Menu
·
·
Press and hold the RIGHT button for 2
seconds to select the voltage
·
·
Press and hold the CENTER button for 2
seconds, the voltage starts to flash, now
you can adjust the voltage:
·
·
Increase(LEFT button) or reduce
(RIGHT button) 0.1V each press.
Maximum adjustment range: ± 1v
·
·
After adjustment, press the CENTER
button to select the voltage, then press
it again to save and exit.
16.8v RunCam 01:08
·
·
Voltage Calibration

Camera Menu
·
·
CAM TITLE (ON/OFF)
·
·
LANGUAGE (English/中文)
·
·
DPC (Cover the lens then press enter key)
·
·
SHUTTER (AUTO / 50-100000 / FLK)
·
·
BRIGHTNESS (50 / 0-255)
·
·
AGC (OFF / LOW / MIDDLE / HIGH)
·
·
EXPOSURE ·
·
MAIN MENU
·
·
WHITE BAL (ATW1 / ATW2 / AWC→SET /
MANUAL: MANUAL, INDOOR, OUTDOOR) ·
·
DWDR (ON: 63 0-63 / OFF)
EXPOSURE
SHUTTER
BRIGHTNESS 050
AGC
DWDR
RETURN
AUTO
OFF
RET
ON
SETUP
CAM TITLE
EXPOSURE
WHITE BAL
BACKLIGHT
DAY & NIGHT
DPC
IMAGE ADJ
LANGUAGE
RESET
EXIT
AT W1
ENGLISH
OFF
COLOR

IMAGE ADJ
LENS SHAD
2DNR
MIRROR
FONT COLOR
CONTRAST
SHARPNESS
DISPLAY
NEG IMAGE
RETURN
OFF
OFF
OFF
110
026
USER
OFF
·
·
IMAGE ADJ
·
·
LENS SHAD (OFF/ ON:22 0-255)
·
·
CONTRAST (110 / 0-255)
·
·
SHARPNESS (26 / 0-31)
·
·
DISPLAY (CRT/LCD/USER)
·
·
GAMMA (0.5 / 0.05-1.0)
·
·
PED LEVEL (17 / 0-63)
Camera Menu
USER ADJ.
RETURN
GAMMA
PED LEVEL
COLOR GAIN
0.50
017
RET
176
·
·
COLOR GAIN (176 / 0-255)

Camera Menu
·
·
AREA SEL (AREA1/AREA2)
·
·
BACKLIGHT (BLC / HLC / OFF)
·
·
GAIN (042 / 0-255 )
·
·
HEIGHT (4 / 0-10)
·
·
LEVEL (200 / 0-255)
·
·
MODE (ALL DAY / NIGHT ONLY )
·
·
WIDTH (3 / 0-9)
·
·
LEFT/RIGHT (6 / 0-6)
·
·
TOP/BOTTOM (10 / 0-10)
BLC
042
004
003
006
005
AREA SEL
AREA STATE
GAIN
HEIGHT
WIDTH
LEFT/RIGHT
TOP/BOTTOM
RETURN
AREA1
ON
RET
200
HLC
LEVEL
MODE
RETURN
ALL DAY
RET

·
·
DAY NIGHT LEVEL (80 / 0-176)
·
·
DAY NIGHT DELAY (3 / 1-30)
·
·
NIGHT DAY LEVEL (032 / 0-255)
·
·
NIGHT DAY DELAY (1 / 1-30)
Camera Menu
·
·
BURST (OFF/ON)
·
·
IR SMART (OFF/ON)
·
·
IR LEVEL (HIGH/LOW)
·
·
DAY & NIGHT (AUTO / COLOR / B&W / EXT)
D & N AUTO
080
SEC
032
SEC
3
1
D N LEVEL
D N DELAY
N D LEVEL
N D DELAY
RETURN RET
D & N B & W
BURST
IR SMART
IR LEVEL
RETURN
OFF
OFF
HIGH
RET

Model
Image Sensor
Horizontal Resolution
Lens
Signal System
Integrated OSD
S/N Ratio
Electronic Shutter Speed
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Min. Illumination
WDR
DNR
Day/Night
Power
Net Weight
Dimensions
RunCam Swift 2
1/3″SONY SUPER HAD II CCD
600TVL
2.5mm (Default) / 2.3mm / 2.1mm
PAL/NTSC
Yes
Yes
>60dB (AGC OFF)
Yes
Yes
0.01L[email protected]
PAL: 1/50~100,000; NTSC: 1/60~100,000
D-WDR
2DNR
Color/Auto/B&W
DC 5-36V
14g
28.5mm*26mm*26mm
Integrated MIC