SA Sport 355 Configuration guide

ASSEMBLY AND CARE INSTRUCTIONS
JUST FOR KIDS
355
VERSION: 8920100 (Revised 05/15)
SALES AND SERVICE
sasportonline.com
SA Sport – Canada and International
135 Forestview Road, PO Box 40
Orillia, Ontario, Canada L3V 6H9
Toll-Free: [phone]
Telephone: [phone]
Fax: [phone]
[email protected]
SA Sport – USA
104 Nu Energy Drive, Suite 1
Aledo, Texas, USA 76008
Toll-Free: [phone]
Telephone: [phone]
Fax: [phone]
[email protected]

355 JUST FOR KIDS Assembly Instructions
Page 2 of 25
Thank you for purchasing a product from our line of Just for Kids Gymnastics Apparatus. We
appreciate your business and value you as a customer.
Our immensely popular Just for Kids line of equipment will attract your littlest gym members – even
tots! You can build it a piece at a time as your budget allows or as a whole circuit in as little as 17’ x
17’ feet of floor space. Not only are all Just for Kids parts interchangeable, but you can also convert
your primary pieces of equipment into a wide range of fun, preschool accessories. Just for Kids grows
with you.
This apparatus is manufactured of the finest materials and has been thoroughly inspected before
leaving our plant. We are sure you will be pleased with its quality, durability and performance.
Please read the following instructions carefully before assembling and using your new equipment, as
they pertain to the particular apparatus you have purchased.
The exclamation mark symbol when seen in this manual is used to indicate warnings or items
that require special attention during the use or assembly of the apparatus.
Assembly, set-up and adjustment of this equipment should only be undertaken by
qualified persons. At no time should children or other unqualified persons undertake
the assembly, set-up, installation or adjustment of this equipment.
THE SA SPORT JUST FOR KIDS LINE IS DESIGNED AND INTENDED FOR USE BY
BEGINNER LEVEL GYMNASTS UNDER A WEIGHT OF 150 LBS (68 KG).
For assembly and set-up instructions, please read and follow all instructions below as they apply to
your particular piece or pieces of equipment.
Tools Required:
•7/32” & 3/16” Allen keys (Supplied with Just For Kids apparatus)
•2 Adjustable Wrenches
•3/4” or 19mm Socket, Extension and Ratchet
•Tape measure
•5/8” diameter carbide concrete drill bit
•Hammer drill, Shop Vacuum
•Anchor setting tool or Drift punch with a 5/16” diameter & at least 1.5” long end
•Hammer
•Safety Glasses
For information on REPLACEMENT PARTS, please see second section of this manual.
Be sure to read and follow all SAFETY INSTRUCTIONS on the last page of this manual before
attempting to use the apparatus.

355 JUST FOR KIDS Assembly Instructions
Page 3 of 25
Table of contents
1. Apparatus description.................................................................................................................4
1.1. 360 - Just For Kids Parallel Bars ............................................................................................4
1.2. 361 - Just For Kids Uneven Bars............................................................................................4
1.3. 362 - Just for Kids High Bar....................................................................................................4
1.4. 363 - Just for Kids Ring Frame...............................................................................................5
1.5. 364 - Just For Kids Low Bar ...................................................................................................5
1.6. 355-CS - Just for Kids Complete System ...............................................................................5
1.7. 355-55 - Just for Kids High Rail Assembly..............................................................................6
1.8. 355-60 - Just for Kids Low Rail Assembly ..............................................................................6
1.9. 355-105 Just for Kids Ring Frame Adjusting Tubes Assembly...............................................6
2. Set-Up, Assembly and Adjustments ..........................................................................................8
2.1. Pre-Assembly Instruction for Just for Kids Uprights (#355-05)...............................................9
2.2. Installing Concrete Anchors..................................................................................................10
2.3. Just for Kids Individual Base Tie-Down - 355-01..................................................................11
2.4. Just for Kids Complete System Base Tie-Down - 355-CS....................................................13
2.5. Just for Kids In-Line Layout Base Tie-Down.........................................................................16
2.6. Just for Kids Rail to Adjusting Tube Assembly .....................................................................18
2.7. Just for Kids Rail & Adjusting Tube Assembly to Uprights Assembly...................................19
2.8. Just for Kids Ring Frame to Uprights Assembly ...................................................................21
2.9. Changing Just for Kids Apparatus Configurations ................................................................22
2.10. Equipment Height Adjustment ..............................................................................................22
2.11. Horizontal Adjustment of Uprights ........................................................................................23
3. Spare parts.................................................................................................................................24
4. SAFETY.......................................................................................................................................25

355 JUST FOR KIDS Assembly Instructions
Page 4 of 25
1. Apparatus description
1.1. 360 - Just For Kids Parallel Bars
The SA Sport 360 Just for Kids Parallel Bars includes the following items:
•Just for Kids Base Assembly (#355-01): 1 Pair
oComplete with Tie-Down Hardware
•Just for Kids Upright Assembly (#355-352): 4 Pieces
oAssembled c/w Locking device & clamp
•Just for Kids Cross Tube (#355-360): 2 Pieces
•Just for Kids Low Adjusting Tube (#355-62): 4 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 2 Pieces
oComplete with mounting hardware
1.2. 361 - Just For Kids Uneven Bars
The SA Sport 361 Just for Kids Uneven Bars includes the following items:
•Just for Kids Base Assembly (#355-01): 1 Pair
oComplete with tie-down hardware
•Just for Kids Upright Assembly (#355-352): 4 Pieces
oAssembled c/w Locking device & clamp
•Just for Kids Cross Tube (#355-360): 2 Pieces
•Just for Kids Low Adjusting Tube (#355-62): 2 Pieces
•Just for Kids High Adjusting Tube (#355-57): 2 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 2 Pieces
oComplete with mounting hardware
1.3. 362 - Just for Kids High Bar
The SA Sport 362 Just for Kids High Bar includes the following items:
•Just for Kids Base Assembly (#355-01): 1 Pair
oComplete with tie-down hardware
•Just for Kids Upright Assembly (#355-352): 2 Pieces
oAssembled c/w Locking device & clamp
•Just for Kids Cross Tube (#355-360): 1 Piece
•Just for Kids High Adjusting Tube (#355-57): 2 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 1 Piece
oComplete with mounting hardware

355 JUST FOR KIDS Assembly Instructions
Page 5 of 25
1.4. 363 - Just for Kids Ring Frame
The SA Sport 363 Just for Kids Ring Frame includes the following items:
•Just for Kids Base Assembly (#355-01): 1 Pair
oComplete with mounting hardware
•Just for Kids Upright Assembly (#355-352): 2 Pieces
oAssembled c/w Locking device & clamp
•Just for Kids Cross Tube (#355-360): 1 Piece
•Just for Kids Ring Frame Adjusting Tube (#355-306): 2 Pieces
•Just for Kids Set of Rings (#355-110): 1 Pair
1.5. 364 - Just For Kids Low Bar
The SA Sport 364 Just for Kids Low Bar includes the following items:
•Just for Kids Base Assembly (#355-01): 1 Pair
oComplete with Tie-Down Hardware
•Just for Kids Upright Assembly (#355-352): 2 Pieces
oAssembled c/w Locking device & clamp
•Just for Kids Cross Tube (#355-360): 1 Piece
•Just for Kids Low Adjusting Tube (#355-62): 2 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 1 Piece
oComplete with mounting hardware
1.6. 355-CS - Just for Kids Complete System
The SA Sport 355-CS Just for Kids Complete System includes 1 each of the Apparatus Assemblies
360, 361, 362 and 363 as well as a 4 Station Circuit Base and a 4-piece set of Multi color Circuit
Mats. The following is a breakdown of all components for reference:
•Just for Kids Base Assembly (#355-01): 4 Pairs
oComplete with Tie-Down Hardware
•Just for Kids Upright Assembly (#355-352): 12 Pieces
oAssembled c/w Locking device & clamp
•Just for Kids Cross Tube (#355-360): 6 Pieces
•Just for Kids High Adjusting Tube (#355-57): 4 Pieces
•Just for Kids Low Adjusting Tube (#355-62): 6 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 5 Pieces
oComplete with mounting hardware
•Just for Kids Ring Frame Adjusting Tube (#355-306): 2 Pieces
•Just for Kids Set of Rings (#355-110): 1 Pair
•Just for Kids 4 Station Circuit Base (#355-154): 1 Piece
oComplete with Tie-Down Hardware
•Just for Kids 4 Pieces Set Circuit Mat (#355-230): 1 Set

355 JUST FOR KIDS Assembly Instructions
Page 6 of 25
1.7. 355-55 - Just for Kids High Rail Assembly
The SA Sport 355-55 Just for Kids High Rail Assembly includes the
following items:
•Just for Kids High Adjusting Tube (#355-57): 2 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 1 Piece
oComplete with mounting hardware
1.8. 355-60 - Just for Kids Low Rail Assembly
The SA Sport 355-60 Just for Kids Low Rail Assembly includes the
following items:
•Just for Kids Low Adjusting Tube (#355-62): 2 Pieces
•Just for Kids Veneered Fiberglass Rail (#355-65): 1 Piece
oComplete with mounting hardware
1.9. 355-105Just for Kids Ring Frame Adjusting
Tubes Assembly
The SA Sport 355-105 Just for Kids Ring Tower Adjusting
Tubes Assembly includes the following items:
•Ring Frame Adjusting Tube (#355-306): 2 Pieces
•Rings Assembly (#355-110): 1 Pair
oAssembled c/w straps & Quick Link

355 JUST FOR KIDS Assembly Instructions
Page 7 of 25

355 JUST FOR KIDS Assembly Instructions
Page 8 of 25
2. Set-Up, Assembly and Adjustments
Please first refer to sections 2.1. Pre-Assembly of Just for Kids Uprights & 2.2. Installing
Concrete Anchors.
Depending on the layout you chose for your Just for Kids Apparatus, please refer to the following
sections:
2.3 Just for Kids Individual Base Tie-Down - 355-01 Page 11
2.4 Just for Kids Complete System Base Tie-Down - 355-CS Page 13
2.5 Just for Kids In-Line Layout Base Tie-Down Page 16
Once bases are set-up properly, please refer to next assembly steps starting on Page 18.

355 JUST FOR KIDS Assembly Instructions
Page 9 of 25
2.1. Pre-Assembly Instruction for Just for Kids Uprights (#355-05)
This step must be done first, before any further Assembly of your Apparatus! Ensure
the screws are tightened securely!
1. Locate the two Just for Kids Uprights (#355-352), one
Just for Kids Cross Tube (#355-360) and the 7/32”
Allen key.
2. Slide the Cross Tube over the connection block with the
hole facing upwards as shown. Line up the holes and
thread the supplied 3/8” Flat Head Screw into the hole.
Tighten screw firmly with a 7/32” Allen key. (Fig. 1)
3. Repeat previous step to assemble the second Upright to
the Cross tube. The resulting assembly is now referred to
as a Just for Kids Upright Assembly Part #355-05.
4. Ensure the assembly is stable before proceeding.
Refer to the instructions below for complete details on Base fastening and assembly
of all other related components for the particular Just For Kids Apparatus.
Fig. 1
3/8” FLAT
HEAD SCREW
CROSS TUBE
UPRIGHT
CONNECTION BLOCK

355 JUST FOR KIDS Assembly Instructions
Page 10 of 25
2.2. Installing Concrete Anchors
To determine anchor locations, please refer to the section for the specific equipment
to be anchored. Anchors & Hardware are supplied with the Just for Kids Base
Assembly (#355-01).
Tools Required (customer supplied):
•Tape measure
•Anchor setting tool or punch with a 5/16” diameter & 1.5” long end
•5/8” diameter carbide tipped concrete drill bit
•Hammer drill
•3/4” or 19mm Socket, Extension and Ratchet
•Hammer
•Shop Vacuum for fine dust
SAFETY GLASSES, TO BE WORN DURING DRILLING, ANCHOR INSTALLATION AND
SETTING!
NEVER PLACE A FLOOR ANCHOR INTO A SEAM/CRACK, OR AN AREA WITHIN 9”
FROM A SEAM/CRACK OR OUTSIDE EDGE OF THE CONCRETE FLOOR.
1. With the 5/8” carbide drill bit installed in the Hammer drill, drill
a hole into the concrete to 2 inches depth (+1/8”).
2. Use a shop vacuum or turkey baster to remove all dust and
concrete chips out of the holes. Ensure the hole depth is at
least 2 inches (+1/8”).
3. Turn a hex head bolt 3 full turns into a floor anchor, and insert
it into the drilled hole (Fig. 2).
4. Use the hammer to tap the top of the bolt until the floor anchor
is flush with or just below the top of the concrete (Fig. 2).
5. Remove the hex head bolt, proceed to set the anchor and lock
it in place.
THE STEP OF LOCKING OR SETTING THE ANCHORS
IS CRITICAL. ENSURE THAT IT IS DONE CORRECTLY
(FIG. 3)!
6. Using a punch or setting tool (customer supplied), set the floor
anchor by striking the plunger in the center of the floor anchor.
Strike the setting tool or punch with a hammer repeatedly, to
expand the anchor in the hole (Fig. 3).
WHEN SECURING EQUIPMENT TO FLOOR ANCHORS
USING BOLTS, A TORQUE VALUE OF 20 FT LBS IS RECOMMENDED.
Fig. 2
Fig. 3

355 JUST FOR KIDS Assembly Instructions
Page 11 of 25
2.3. Just for Kids Individual Base Tie-Down - 355-01
SA SPORT RECOMMENDS THAT THE JUST FOR KIDS BASES
BE BOLTED TO THE FLOOR.They have been designed and
supplied with the required hardware for bolting to a concrete floor.
This procedure will require at least two (2) qualified
persons. Children or other unqualified personnel
should at no time undertake any part of this
procedure.
1. Position the apparatus in the desired location. Align both Just for Kids Bases (#355-01) as
shown in Fig. 4 below.
2. Install 1 or 2 Just for Kids Upright Assemblies (#355-05 previously assembled) between the 2
(#355-01) Bases (Fig. 4). Tighten the clamp (Fig. 4A) on the lower section of each side of the
Just for Kids Upright Assemblies (#355-05) by turning CLOCKWISE. This will assist in maintaining
the correct width and alignment. Use diagonal measurements (99-7/8”) to help square up
bases. When measured, the two diagonal distances should be approximately the same.
THE BASES MUST BE PARALLEL TO EACH OTHER TO ALLOW FOR PROPER AND
COMPLETE HORIZONTAL ADJUSTMENT OF THE UPRIGHTS ALONG THE LENGTH
OF THE BASES.
Fig. 4
Fig. 4A

355 JUST FOR KIDS Assembly Instructions
Page 12 of 25
3. On the top surface of each Just for Kids Base, there are two (2)
holes that reveal the anchor holes (Fig. 5).
SAFETY GLASSES, TO BE WORN DURING DRILLING,
ANCHOR INSTALLATION AND SETTING!
4. Drill the 4 holes for the floor anchors using the anchor holes in the 2 Just for Kids Bases as
guides (see Fig. 4 above). Drill the holes 5/8” diameter to a depth equal to the length (2 inches) of
the floor anchor +1/8”.
REFER TO PAGE 9 FOR COMPLETE INSTRUCTIONS ON PROPER INSTALLATION OF
FLOOR ANCHORS!
NEVER PLACE A FLOOR ANCHOR INTO A SEAM/CRACK, OR AN AREA WITHIN 9”
FROM A SEAM/CRACK OR OUTSIDE EDGE OF THE CONCRETE FLOOR.
5. Move the apparatus aside. Vacuum the holes to remove all dust and concrete chips.
6. Insert the floor anchors, threaded end up & slotted end down, into the drilled holes. Ensure the
top of the floor anchor is flush with or just below the top of the concrete.
7. Set each of the floor anchors by striking the plunger in the center of the floor anchor as per page
9.
ENSURE THAT THE ANCHORS ARE PROPERLY SET OR THE SAFE USE OF THE
EQUIPMENT MAY BE COMPROMISED!
8. Reposition the apparatus over the floor anchor and bolt down the Just for Kids Bases (see Fig. 4)
loosely. Ensure that Bases are parallel to each other and install 1 or 2 Just for Kids Upright
(#355-05) on to the 2 Bases (#355-01). This will assist in maintaining the correct width between
the bases as well as maintaining them parallel to each other.
9. Now that the uprights are installed, tighten the bolts down on the bases securely.
10.Install the plastic caps in the indicated holes shown in Fig. 5 of the top of the Bases.
Fig. 5

355 JUST FOR KIDS Assembly Instructions
Page 13 of 25
2.4. Just for Kids Complete System Base Tie-Down - 355-CS
This part requires (1) Just for Kids 4-Station Circuit Base (#355-154) & (4) Just for Kids Single
Bases (#355-01). Since the Just for Kids 4-Station Circuit comes with (1) Just for Kids 4-Station
Circuit Base & (8) Just for Kids Single Bases, you will have (4) Just for Kids Single Bases left
over by choosing this layout.
SA SPORT RECOMMENDS THAT THE JUST FOR
KIDS 4-STATION CIRCUIT BASE & THE JUST FOR
KIDS SINGLE BASES BE BOLTED TO THE FLOOR.
They have been designed and supplied with the
required hardware for bolting to a concrete floor.
This procedure will require at least two (2)
qualified persons. Children or other
unqualified personnel should at no time
undertake any part of this procedure.
1. Position the 4-Station Circuit Base (#355-154) in the center of the desired location for the
apparatus to be set up. The complete 4-station Circuit uses a floor area greater than 17 feet x
17 feet square.
2. Position the 4 Base Leg assemblies (#355-01), around the 4-Station Circuit Base, as shown in
Fig. 6 on the next page.
3. Beginning with Station #1, install 2 Just for Kids Upright assemblies (#355-05) between the
Just for Kids 4-Station Circuit Base (#355-154) & one of the Just for Kids Single Base (#355-
01). Tighten the clamp (Fig. 4A) on the lower section of each side of the Just for Kids Upright
Assemblies (#355-05) by turning CLOCKWISE. This will assist in maintaining the correct width
and alignment.
THE BASES MUST BE PARALLEL TO EACH OTHER TO ALLOW FOR PROPER AND
COMPLETE HORIZONTAL ADJUSTMENT OF THE UPRIGHTS ALONG THE LENGTH
OF THE BASES.
4. Using a measure tape, measure the diagonal corner to corner distance of the bases in Station 1
as shown in Fig. 4 on the next page. If required, loosen the Clamp on the Upright of the Just for
Kids Single Base (#355-01) side and slide the Just for Kids Single Base (#355-01) as required to
even out the diagonal distance. Use diagonal measurements (92-3/8”) to help square up the
bases. When measured, the two diagonal distances should be approximately the same.
5. Then proceed to each of the 3 other stations and install one or two uprights, measure and adjust
the diagonal distance of each base. Once all uprights are installed, take the time to observe your
proposed apparatus layout and ensure that there is sufficient floor space for landing mats. Make
any adjustments in the location at this point prior to proceeding to anchoring the apparatus to the
concrete.

355 JUST FOR KIDS Assembly Instructions
Page 14 of 25
Fig. 6
Fig. 6A

355 JUST FOR KIDS Assembly Instructions
Page 15 of 25
6. On the top surface of each Just for Kids Single Base (#355-01)
and the Just for Kids 4-Station Circuit Base (#355-154), there
are holes which reveal the anchor holes (Fig. 7).
SAFETY GLASSES, TO BE WORN DURING DRILLING,
ANCHOR INSTALLATION AND SETTING!
7. Begin with the Just for Kids 4-Station Circuit Base by drilling
the 4 holes for the floor anchors using the 4 anchor holes in
the 4 station Circuit Base as guides (see Fig. 6 above). Drill
the holes 5/8” diameter to a depth equal to the length (2
inches) of the floor anchor +1/8”.
REFER TO PAGE 9 FOR COMPLETE INSTRUCTIONS ON PROPER INSTALLATION OF
FLOOR ANCHORS!
NEVER PLACE A FLOOR ANCHOR INTO A SEAM/CRACK, OR AN AREA WITHIN 9”
FROM A SEAM/CRACK OR OUTSIDE EDGE OF THE CONCRETE FLOOR.
In order to minimize the possibility that holes don’t line up as you progress to drill all
the holes, it is strongly advised, to clean out each hole after drilling and drop a 5/8”
diameter rod or bolt 5” long or longer (customer supplied) in each drilled hole to help
keep the apparatus aligned to the drilled holes. (Ensure that these be easily removed
after drilling all the holes)
8. Once the Just for Kids 4-Station Circuit Base is drilled, move on to each of the Just for Kids Single
Base (#355-01) and drill the remaining 8 holes for the floor anchors using the anchor holes in the
4 Just for Kids Single Bases as guides (Fig. 6). Drill the holes 5/8” diameter to a depth equal to
the length (2 inches) of the floor anchor +1/8”, as per Page 9 Anchor Installation.
9. Move the apparatus aside. Vacuum the holes to remove all dust and concrete chips.
10.Insert the floor anchors, threaded end up & slotted end down, into the drilled holes. Ensure the
top of the floor anchor is flush with or just below the top of the concrete.
11.Set each of the floor anchors by striking the plunger in the center of the floor anchor as per Page
9.
ENSURE THAT THE ANCHORS ARE PROPERLY SET OR THE SAFE USE OF THE
EQUIPMENT MAY BE COMPROMISED!
12.Reposition the apparatus over the floor anchor and bolt down the Just for Kids 4-Station Circuit
Base and Single Bases (see Fig. 6) loosely. Ensure that Bases assemblies are parallel to each
other by installing 1 or 2 Just for Kids Upright assemblies (#355-05) between the 2 Bases. This
will assist in maintaining the correct width between the bases as well as maintaining them parallel
to each other.
13.Now that the uprights are installed, tighten the bolts down on the bases securely.
14.Install the plastic caps in the indicated holes shown in Fig. 7 of the top of the Bases.
Fig. 7

355 JUST FOR KIDS Assembly Instructions
Page 16 of 25
2.5. Just for Kids In-Line Layout Base Tie-Down
This part requires (5) Just for Kids Single Bases (#355-01). Since each Just for Kids Apparatus
comes with (2) Just for Kids Single Bases, you will have (3) Just for Kids Single Bases left over
by choosing this layout.
SA SPORT RECOMMENDS THAT THE JUST FOR KIDS BASES BE BOLTED TO THE FLOOR.
They have been designed and supplied with the required hardware for bolting to a concrete floor.
This procedure will require at least two (2) qualified persons. Children or other
unqualified personnel should at no time undertake any part of this procedure.
1. Position the apparatus in the desired location. Align all Just for Kids Bases (#355-01) as shown
in Fig. 8 below.
2. Install 1 or 2 Just for Kids Upright Assemblies (#355-05 previously assembled) between each
Just for Kids Single Base (#355-01) (Fig. 8). Tighten the clamp (Fig. 8A) on the lower section
of each side of the Just for Kids Upright Assemblies (#355-05) by turning CLOCKWISE. This will
assist in maintaining the correct width and alignment. Use diagonal measurements (99-7/8”) to
help square up bases. When measured, the two diagonal distances should be
approximately the same for each pair of bases.
THE BASES MUST BE PARALLEL TO EACH OTHER TO ALLOW FOR PROPER AND
COMPLETE HORIZONTAL ADJUSTMENT OF THE UPRIGHTS ALONG THE LENGTH
OF THE BASES.
Fig. 8
Fig. 8A

355 JUST FOR KIDS Assembly Instructions
Page 17 of 25
3. On the top surface of each Just for Kids Base, there are two (2)
holes that reveal the anchor holes (Fig. 9).
SAFETY GLASSES, TO BE WORN DURING DRILLING,
ANCHOR INSTALLATION AND SETTING!
4. Drill the 4 holes for the floor anchors using the anchor holes in the 2 Just for Kids Bases as
guides (see Fig. 8 above). Drill the holes 5/8” diameter to a depth equal to the length (2 inches) of
the floor anchor +1/8”.
REFER TO PAGE 9 FOR COMPLETE INSTRUCTIONS ON PROPER INSTALLATION OF
FLOOR ANCHORS!
NEVER PLACE A FLOOR ANCHOR INTO A SEAM/CRACK, OR AN AREA WITHIN 9”
FROM A SEAM/CRACK OR OUTSIDE EDGE OF THE CONCRETE FLOOR.
5. Move the apparatus aside. Vacuum the holes to remove all dust and concrete chips.
6. Insert the floor anchors, threaded end up & slotted end down, into the drilled holes. Ensure the
top of the floor anchor is flush with or just below the top of the concrete.
7. Set each of the floor anchors by striking the plunger in the center of the floor anchor as per page
9.
ENSURE THAT THE ANCHORS ARE PROPERLY SET OR THE SAFE USE OF THE
EQUIPMENT MAY BE COMPROMISED!
8. Reposition the apparatus over the floor anchor and bolt down the Just for Kids Bases (see Fig. 8)
loosely. Ensure that Bases are parallel to each other and install 1 or 2 Just for Kids Upright
(#355-05) on each pair of Bases (#355-01). This will assist in maintaining the correct width
between the bases as well as maintaining them parallel to each other.
9. Now that the uprights are installed, tighten the bolts down on the bases securely.
10.Install the plastic caps in the indicated holes shown in Fig. 5 of the top of the Bases.
Fig. 9

355 JUST FOR KIDS Assembly Instructions
Page 18 of 25
2.6. Just for Kids Rail to Adjusting Tube Assembly
This procedure will require at least two (2)
qualified persons. Children or other
unqualified personnel should at no time
undertake any part of this procedure.
The length of the Just for Kids Adjusting Tube you are
working with will vary depending on the Just for Kids product
that you are assembling. However, the procedure for
assembling rails and adjusting tubes is the same for all
products.
1. Locate one (1) rail and two (2) Adjusting Tubes.
If you are assembling Just for Kids Uneven
Bars, ensure that the Adjusting Tube you select
are equal in length when assembling each of
the 2 rail heights.
2. Remove the Nylock Nuts and mounting Bolts from the
rail U-bracket located on the end of each rail.
3. Working with one (1) Adjusting Tube at a time, place the rail pivot, which is located at one end of the
Adjusting Tube, into the U-bracket. See Fig. 10 below. The locking holes in the Adjusting Tube must
face to the outside (end of the rail).
4. Align the hole in the rail pivot with the one in the U-bracket and insert the mounting Bolt through these
holes. Install the Nylock nut with the nylon ring facing away from the U-bracket.
5. Tighten the Nylock & bolt snug, but don’t over tighten. A small space between the U-brackets and rail pivot
need to allow for the bar to flex. See Fig. 10 below.
When tightening the nut and bolt, the Nylon Ring in the Nylock nut must be past the end of the
threads of the bolt to ensure that the nut won’t come loose.
6. Repeat steps 3 to 5 with a second Just for
Kids Adjusting Tube at the opposite end of the
Rail.
7. If you are assembling Just for Kids Parallel
Bars or Uneven Bars, repeat Steps 1 through
6 with the other Rail and Adjusting Tubes.
Fig. 10

355 JUST FOR KIDS Assembly Instructions
Page 19 of 25
2.7. Just for Kids Rail & Adjusting Tube Assembly to Uprights Assembly
This procedure will require at least two
(2) qualified persons. Children or other
unqualified personnel should at no time
undertake any part of this procedure.
1. Locate one (1) Just for Kids Upright Assembly
(#355-05).
See Page 9, Pre-assembly of Just for
Kids Uprights, if this step was missed.
2. Install the Just for Kids Upright between the
Bases (refer to section on Bases Tie-Down if
required) and tighten the clamp (Fig. 11) on the
lower section of each side of the Upright
Assembly by turning Clockwise.
Mounting the Upright Assembly on to the Bases must be done at this time in order to
prevent the completed assembly from toppling over.
3. Loosen the Spin-Snap Lock on each side of the Upright Assembly by turning the Spin Lock
portion, round disc, counterclockwise. Turn the handle counterclockwise until it stops, but do not
force it any further. This stop prevents the Spin Lock from being removed.
4. Loosen the 3/8” Flat Head Screw which link the uprights to
the base tube.
3/8” FLAT
HEAD SCREW
BASE TUBE
UPRIGHT END
CONNECTION BLOCK
Fig. 11

355 JUST FOR KIDS Assembly Instructions
Page 20 of 25
5. Prepare to slide the Rail & Adjusting Tube Assembly into the Upright
Assembly (See Fig. 12). Lower the Rail & Adjusting Tube Assembly into
the Uprights. Pull outward on the Snap Lock Device. Once the Adjusting
Tube reaches the pin, lower the rail while releasing the Snap Lock
Device until the 1
st
Adjusting Tube hole allows the pin to fall into the
locking hole. The Snap Lock Device is now engaged.
To avoid injury while lowering the rail into position, keep
hands well clear of the adjusting tubes where they slide into
the Uprights.
6. Position the rail at a height that will be comfortable to work with during
the set-up of the apparatus and engage the Snap Lock Device so that
the pin drops into a hole. Tighten the Spin Lock portion securely by
turning it clockwise.
7. Thread now the 3/8” Flat Head Screw to attach the uprights to the base
tube firmly.
8. If you are assembling the Just for Kids Parallel Bars or Uneven Bars,
repeat Steps 1 through 6 with the second Upright Assembly and Rail &
Adjusting Tube Assembly.
To avoid possible injury and/or damage to the first Rail &
Adjusting Tube Assembly while working with the second
Upright, ensure that the first Assembly is either mounted &
locked to the Bases or well clear of the working area and
cannot be accidentally tipped over.
Fig. 12