SA Sport JFK User manual

JFK / Product & Installation Instructions #8920100
February 2, 2015
sasportonline.com
Sales & Service
SA Sport (Canada) SA Sport (U.S.A.)
135 Forestview Road 7879 Will Rogers Blvd.
P.O. Box 40 Fort Worth, Texas
Orillia, Ontario USA 76140
Canada L3V 6H9
Telephone: [phone] Telephone: [phone]
Fax: [phone] Fax: [phone]
Toll Free: [phone] Toll Free: [phone]
“JFK” - Just For Kids

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 2
Thank you for purchasing a product from our line of Just for Kids Gymnastics Apparatus. We
appreciate your business and value you as a customer.
Our immensely popular Just for Kids line of equipment will attract your littlest gym members –
even tots! You can build it a piece at a time as your budget allows or as a whole circuit in as
little as 17’ x 17’ feet of floor space. Not only are all Just for Kids parts interchangeable, but
you can also convert your primary pieces of equipment into a wide range of fun, preschool
accessories. Just for Kids grows with you.
This apparatus is manufactured of the finest materials and has been thoroughly inspected before
leaving our plant. We are sure you will be pleased with its quality, durability and performance.
Please read the following instructions carefully before assembling and using your new
equipment, as they pertain to the particular Apparatus you have purchased.
The exclamation mark symbol when seen in this booklet is used to indicate warnings or
items that require special attention during the use or assembly of the apparatus.
Assembly, set-up and adjustment of this equipment should only be undertaken by
qualified persons. At no time should children or other unqualified persons undertake the
assembly, set-up, installation or adjustment of this equipment.
The S/A Sport Just for Kids Line is designed and intended for use by beginner level
gymnasts under a weight of 150 lbs (68 kg).
For assembly and set-up instructions, please read and follow all instructions in Section II of this
booklet as they apply to your particular piece or pieces of equipment.
Tools Required:
•7/32” & 3/16” Allen keys (Supplied in bag attached to instructions)
•2 Adjustable Wrenches
•¾” or 19mm Socket, Extension and Ratchet
•Tape measure
•5/8” diameter carbide concrete drill bit
•Hammer drill, Shop Vacuum
•Anchor setting tool or Drift punch with a 5/16” diameter & at least 1.5” long end
•Hammer
•Safety Glasses
Be sure to read and follow all Safety Instructions in Section III of this booklet before attempting
to use the apparatus!
For information on Replacement Parts, please see Section IV of this booklet.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 3
SECTION I The Apparatus Description Page
360
Just for Kids
Parallel Bars
4
361
Just for Kids
Uneven Bars
4
362
Just for Kids
High Bar
4
363
Just for Kids
Ring Frame
5
364
Just for Kids
Single Low Bar
5
355
-
CS
Just for Kids
Complete System c/w 4
Mats
5
355
-
55
Just for Kids
High Rail Assembly
6
355
-
60
Just for Kids
Low Rail Assembly
6
355
-
105
Just for Kids
Ring Frame Adjusting Tubes c/w Rings
6
Chart
Just for Kids
Apparatus Component conversion chart
7
SECTION II Set-up, Assembly and Adjustments
Pre
-
Assembly Instruction For Collapsible
JFK
Uprights (355
-
05)
8
Installing concrete Anchors
9
Just for Kids
-
(355
-
01) Base Assemblies Tie
-
Down
10
Just for Kid
-
(355
-
CS) Complete System Base Assemblies Tie
-
Down
( Consisting of (355-154) 4 Station Circuit Base & (355-01) Base Assemblies)
11
Just for Kids
-
Rail to Inner Tube Assembly
14
Just for Kids
-
Rail & Inner Tube to Uprights Assembly
15
Just for Kids
-
Ring Frame to Uprights (Rings Assembly)
16
Just for Kids
-
Atta
ching Rings to Ring Frame Assembly
16
Changing
Just for Kids
Apparatus Configurations
17
Height Adjustments
17
Horizontal Adjustments of Uprights
18
SECTION III Safety
Safety Instructions
18
SECTION IV Spare Parts
Spare parts
19

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 4
Section I THE APPARATUS DESCRIPTION
360 Just For Kids - Parallel Bars
The S/A Sport 360 Just for Kids Parallel Bars includes the following items:
•Base Assembly (#355-01)
oComplete with Tie-Down Hardware 1 pr
•Just for Kids Upright Assembly (#355-312)
oAssembled c/w Locking devices 4 ea.
•Just for Kids Upright Base Assembly (#355-320)
oAssembled c/w clamps 2 ea.
•Inner Tube Assembly – Low Rail (#355-62)
oAssembled c/w rail pivot 4 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 2 ea.
361 Just For Kids - Uneven Bars
The S/A Sport 361 Just for Kids Uneven Bars includes the following items:
•Base Assembly (#355-01)
oComplete with tie-down hardware 1 pr
•Just for Kids Upright Assembly (#355-312)
oAssembled c/w Locking devices 4 ea.
•Just for Kids Upright Base Assembly (#355-320)
oAssembled c/w clamps 2 ea.
•Inner Tube Assembly – High Rail (#355-57)
oAssembled complete with rail pivot 2 ea.
•Inner Tube Assembly – Low Rail (#355-62)
oAssembled complete with rail pivot 2 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 2 ea.
362 Just for Kids - High Bar
The following items are included in the S/A Sport model 362 Just for Kids High Bar:
•Base Assembly (#355-01)
oComplete with tie-down hardware 1 pr
•Just for Kids Upright Assembly (#355-312)
oAssembled c/w Locking devices 2 ea.
•Just for Kids Upright Base Assembly (#355-320)
oAssembled c/w clamps 1 ea.
•Inner Tube Assembly – High Rail (#355-57)
oAssembled complete with rail pivot 2 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 1 ea.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 5
363 Just for Kids - Ring Frame
The S/A Sport 363 Just for Kids Ring Frame includes the following items:
•Base Assembly (#355-01)
oComplete with mounting hardware 1 pr.
•Just for Kids Upright Assembly (#355-312)
oAssembled c/w Locking devices 2 ea.
•Just for Kids Upright Base Assembly (#355-320)
oAssembled c/w clamps 1 ea.
•Ring Frame Adjusting Tube Assembly (#355-105)
oAssembled c/w Rings & mounting hardware 1 pr.
364 Just For Kids – Single Low Bar
The S/A Sport 360W Just for Kids Single Low Bar (Wood Rails) includes the following items:
•Base Assembly (#355-01)
oComplete with Tie-Down Hardware 1 pr
•Just for Kids Upright Assembly (#355-312)
oAssembled c/w Locking devices 2 ea.
•Just for Kids Upright Base Assembly (#355-320)
oAssembled c/w clamps 1 ea.
•Inner Tube Assembly – Low Rail (#355-62)
oAssembled c/w rail pivot 2 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 1 ea.
355-CS Just for Kids –Complete System
The 355-CS Just for Kids Complete System from S/A Sport includes 1 each of the Apparatus Assemblies 360,
361, 362, and 363 as well as a 4 Station Circuit Base and a 4-piece set of Multi color Circuit Mats. The
following is a breakdown of all components for reference:
•Base Assembly (#355-01)
oComplete with tie-down hardware 4 pr
•Just for Kids Upright Assembly (#355-312)
oAssembled c/w Locking devices 12 ea.
•Just for Kids Upright Base Assembly (#355-320)
oAssembled c/w clamps 6 ea.
•Inner Tube Assembly – High Rail (#355-57)
oAssembled complete with rail pivot 4 ea.
•Inner Tube Assembly – Low Rail (#355-62)
oAssembled complete with rail pivot 6 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 5 ea.
•Ring Frame Adjusting Tube Assembly (#355-105)
oAssembled c/w Rings & mounting hardware 1 pr.
•4 Station Circuit Base (#355-154)
oComplete with tie-down hardware 1 ea.
•4 pcs set Circuit Mat (#355-230) 1 set

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 6
355-55 Just for Kids High Rail Assembly
The S/A Sport 355-55W Just for Kids High Rail Assembly (Wood
Rail) includes the following items:
•Inner Tube Assembly – High Rail (#355-57)
oAssembled complete with rail pivot 2 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 1 ea.
355-60 Just for Kids Low Rail Assembly
The S/A Sport 355-60 Just for Kids Low Rail Assembly includes
the following items:
•Inner Tube Assembly – Low Rail (#355-62)
oAssembled, complete with rail pivot 2 ea.
•Fiberglass Rail with Wood Veneer Assembly (#355-65)
oComplete with mounting hardware 1 ea.
355-105 Just for Kids Ring Frame Adjusting Tubes Assembly
The S/A Sport 355-105 Just for Kids Ring Tower Adjusting Tubes
Assembly includes the following items:
•Ring Frame Adjusting Tubes (#355-306)
oComplete with ring mounting hardware 2 ea.
•Rings Assembly (#355-110)
oAssembled c/w straps & Quick Link 1 pr.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 7

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 8
Section II SET-UP, ASSEMBLY AND ADJUSTMENTS
Pre-Assembly Instruction for Collapsible JFK Uprights (355-05)
Note: This step must be done first, before any further Assembly of your Apparatus!
Ensure the screws are tightened securely!
1. Locate the two Upright Ends (355-312), a Base Tube and
the 7/32” Allen key.
2. Slide the Base Tube over the connection block with the hole
facing upwards as shown. Line up the holes and thread the
supplied 3/8” Flat Head Screw into the hole. Tighten screw
firmly with a 7/32” Allen key. (Fig. 1)
3. Repeat previous step to assemble the other upright to the
base tube. The resulting assembly is now referred to as a
JFK Upright Assembly Part #355-05. (Fig. 2)
4. Ensure the assembly is stable before proceeding.
Note: Refer to the Main JFK Assembly literature for complete
details on Base fastening and assembly of all other
related components for the particular Just For Kids
Apparatus.
Fig. 1
Fig. 2 – Uprights and Base Tube Assembled
3/8” FLAT
HEAD SCREW
BASE TUBE
UPRIGHT END
CONNECTION BLOCK

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 9
Installing Concrete Anchors
Note: To determine anchor locations, please refer to the section for the specific equipment
to be anchored, Anchors & hardware are supplied with the Base Assemblies.
Tools Required (customer supplied):
•Tape measure
•Anchor setting tool or punch with a
5
/
16
” diameter & 1.5” long end
•
5
/
8
” diameter carbide tipped concrete drill bit
•Hammer drill
•¾” or 19mm Socket, Extension and Ratchet
•Hammer
•Shop Vacuum for fine dust
•Safety glasses, to be worn during Drilling, Anchor
installation and setting!
Note: Never place a floor anchor into a seam/crack,
or an area within 9” from a seam/crack or
outside edge of the concrete floor
1. With the 5/8” carbide drill bit installed in the Hammer
drill, drill a hole into the concrete to 2 inches (+
1
/
8
”).
2. Use a shop vacuum or turkey baster to remove all dust
and concrete chips out of the holes. Ensure the hole depth is at least 2 inches (+
1
/
8
”).
3. Turn a hex head bolt 3 full turns into a floor anchor, and insert it into the drilled hole (FIG 1).
4. Use the hammer to tap the top of the bolt until the floor
anchor is flush with or just below the top of the concrete
(FIG 1).
5. Remove the hex head bolt, proceed to set the anchor and
lock it in place!
The step of locking or setting the anchors is critical;
ensure that it is done correctly (FIG 2)!
6. Using a punch or setting tool (customer supplied), set
the floor anchor by striking the plunger in the center of
the floor anchor. Strike the setting tool or punch with a
hammer repeatedly, to expand the anchor in the hole
(FIG 2).
When securing equipment to floor anchors using bolts, a torque value of 20 ft lbs is
recommended.
FIG 2
FIG 1

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 10
Just for Kids - (355-01) Base Assemblies Tie-Down
S/A Sport recommends that the Base Assemblies be bolted to the floor.
They have been designed and supplied with the required hardware for
bolting to a concrete floor.
This procedure will require at least two (2) qualified
persons. Children or other unqualified personnel should at
no time undertake any part of this procedure.
1. Position the apparatus in the desired location. Align both Base Leg assemblies (355-01) as shown in FIG 1.
Ensure that the numbers on the side of the bases, the adjustment scale face away from centre.
2. Install 1 or 2 JFK upright assemblies (355-05) between the 2 (355-01) Base Assemblies (FIG 1), Tighten the
clamp (FIG 1A) on the lower section of each side of the “JFK” (355-05) Uprights by turning Clockwise, this
will assist in maintaining the correct width and alignment.
Note: The Base Assemblies must be parallel to each other to allow for proper and complete
horizontal adjustment of the Uprights along the length of the Base Assemblies.
Note: Never place a floor anchor into a crack, or an area within 9” from a crack or into the edge of
the concrete.
FIG 1
Note: Install "JFK" Upright Assemblies onto Bases before
drilling Anchor holes.
Use diagonal Measurements (997
8") to help square up
bases, when measured the two diagonal distances
should be approximately the same.
7

9

8

7

9

8

FIG 1A

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 11
3. On the top surface of each Base Assembly, there are two (2) holes that
reveal the anchor holes; if the plastic caps have been installed they must be
removed to get access to the anchor holes. (FIG 2)
Caution: Safety glasses to be worn during Drilling, Anchor installation & setting!
4. Drill the 4 holes for the floor anchors using the anchor holes in the 2 Base Assemblies as guides (FIG 1).
Drill the holes 5/8” diameter to a depth equal to the length (2 inches) of the floor anchor +1/8”.
Note: Refer to Page 9 for complete instructions on proper installation of Floor Anchors!
5. Move the apparatus aside. Vacuum the holes to remove all dust and concrete chips.
6. Insert the floor anchors, threaded end up & slotted end down, into the drilled holes. Ensure the top of the
floor anchor is flush with or just below the top of the concrete.
7. Set each of the floor anchors by striking the plunger in the center of the floor anchor as per Page 9.
Note: Ensure that the anchors are properly set or the safe use of the equipment may be
compromised!
8. Reposition the apparatus over the floor anchor and bolt down the Base Assemblies (see FIG 1) loosely.
Ensure that Base assemblies are Parallel to each other and install 1 or 2 “JFK” upright assemblies (355-05)
on to the 2 Bases (355-01), this will assist in maintaining the correct width between the bases as well as
maintaining them parallel to each other.
9. Now that the uprights are installed, tighten the bolts down on the bases securely.
10. Install the plastic caps in the indicated holes shown in FIG 2 of the top of the Base Assemblies.
Just for Kids - (355-CS) Complete System Base Assembly Tie-Down
•Requires (1) 4-Station Circuit Base (355-154) & (4) Single Base Assemblies (355-01).
S/A Sport recommends that the 4 Station Circuit Base & base
Assemblies be bolted to the floor. They have been designed
and supplied with the required hardware for bolting to a
concrete floor.
This procedure will require at least two (2) qualified
persons. Children or other unqualified personnel
should at no time undertake any part of this
procedure.
1. Position the 4 Station Circuit Base (355-154) in the center
of the desired location for the apparatus to be set up. The
complete 4-station circuit uses a floor area greater then 17
feet x 17 feet square.
2. Position the 4 Base Leg assemblies (355-01), around the 4 Station Circuit Base, as shown in FIG 4 on the
next page. Ensure that the numbers on the side of the bases, the adjustment scale face away from centre.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 12
Note: Never place a floor anchor into a crack, or an area within 9” from a crack or into the edge of
the concrete.
FIG 4
9

8 7
 
7

8 9
 
FIG 4A
Note: Install "JFK" Upright Assemblies onto Bases before
drilling Anchor holes.
Use diagonal Measurements (92
3
8
") to help square up
bases, when measured the two diagonal distances
should be approximately the same.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 13
FIG 5
3. Beginning with station #1, Install 2 upright assemblies (355-05) between the (355-154) 4 Station Circuit
Base & (355-01) Base Assemblies. Tighten the clamp (FIG 4A) on the lower section of each side of the
Upright Assemblies (355-05) by turning Clockwise; this will assist in maintaining the correct width and
alignment.
Note: The Base Assemblies must be parallel to each other to allow for proper and complete
horizontal adjustment of the Uprights along the length of the Base Assemblies.
4. Using a measure tape measure the diagonal corner to corner distance of the bases in Station 1 as shown in
FIG 4 - “Station 4”. If required, loosen the clamp assembly on the uprights, of the 355-01 Base Assembly
side and slide the (355-01) Base Assembly as required to even out the diagonal distance.
5. Then proceed to each of the 3 other stations and install one or two uprights and measure and adjust the
diagonal distance of each base. Once all uprights are installed take the time to observe your proposed
apparatus layout and ensure that there is sufficient floor space for landing mats. Make any adjustments in the
location at this point prior to proceeding to anchoring the apparatus to the concrete.
6. On the top surface of each Base Assembly and the 4 Station Circuit Base,
there are holes which reveal the anchor holes; if the plastic caps have
been installed they must be removed to get access to the anchor holes.
(See FIG 5)
7. Begin with the 4 Station Circuit Base by drilling the 4 holes for the floor
anchors using the 4 anchor holes in the 4 station Circuit Base as guides
(FIG 4). Drill the holes 5/8” diameter to a depth equal to the length (2
inches) of the floor anchor +1/8”, as per Page 9 Anchor Installation.
Note: Refer to Page 9 for complete instructions on proper installation of Floor Anchors!
Note: In order to minimize the possibility that holes don’t line up as you progress to drill all the
holes, it is strongly advised, to clean out each hole after drilling and drop a 5/8” diameter
rod or bolt 5” or longer (customer supplied) in each drilled hole to help keep the apparatus
aligned to the drilled holes. (Ensure that these be easily removed after drilling all the holes)
8. Once the 4 Station Circuit Base is drilled move on to each of the Base Assemblies (355-01) and drill the
remaining 8 holes for the floor anchors using the anchor holes in the 4 Base Assemblies as guides (FIG 4).
Drill the holes 5/8” diameter to a depth equal to the length (2 inches) of the floor anchor +1/8”, as per Page 9
Anchor Installation.
9. Move the apparatus aside. Vacuum the holes to remove all dust and concrete chips.
10. Insert the floor anchors, threaded end up & slotted end down, into the drilled holes. Ensure the top of the
floor anchor is flush with or just below the top of the concrete.
11. Set each of the floor anchors by striking the plunger in the center of the floor anchor as per Page 9.
Note: Ensure that the anchors are properly set or the safe use of the equipment may be compromised!
12. Reposition the apparatus over the floor anchor and bolt down the 4 Station Circuit Base and Base
Assemblies (see FIG 4) loosely. Ensure that Base assemblies are Parallel to each other by installing 1 or 2
“JFK” upright assemblies (355-05) on to the 2 Bases (355-01), this will assist in maintaining the correct
width between the bases as well as maintaining them parallel to each other.
13. Now that the uprights are installed, tighten the bolts down on the bases securely.
14. Install the plastic caps in the indicated holes shown in FIG 5 of the top of the Bases.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 14
FIG 7
Just for Kids - Rail to Inner Tube Assembly
This procedure will require at least two (2) qualified
persons. At no time should children or other
unqualified personnel undertake any part of this
procedure.
The length of the inner tube assemblies you are working with
will vary depending on the Just for Kids product that you are
assembling. However, the procedure for assembling rails and
inner tube assemblies is same for all products.
1. Locate one (1) rail and two (2) inner tube assemblies.
Note: If you are assembling Just for Kids Uneven
Bars, ensure that the inner tube assemblies
you select are equal in length when
assembling each of the 2 rail heights.
2. Remove the Nylock Nuts and mounting Bolts from the rail
U-bracket located on the end of each rail.
3. Working with one (1) Inner Tube Assembly at a time, place
the rail pivot, which is located at one end of the Inner Tube
Assembly, into the U-bracket. See FIG 7
4. Align the hole in the rail pivot with the one in the U-
bracket and insert the mounting Bolt through these holes. Install
the Nylock nut with the nylon ring facing away from the U-
bracket.
5. Tighten the Nylock & bolt snug, but don’t over
tighten, a small space between the U-brackets
and rail pivot allow for the bar to flex, see fig 7.
Note: When tightening the nut and bolt
the Nylon Ring in the Nylock nut
must be past the end of the threads
of the bolt to ensure that the nut
won’t come loose.
6. Repeat steps 3 to 5 with a second Inner Tube
Assembly at the opposite end of the Rail.
7. If you are assembling Just for Kids Parallel Bars
or Uneven Bars, repeat Steps 1 through 6 with
the other Rail and Inner Tube assemblies.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 15
JFK - Rail & Inner Tube Assembly to Uprights Assembly
This procedure will require at least two (2) qualified
persons. At no time should children or other
unqualified personnel undertake any part of this
procedure.
1. Locate one (1) Upright Assembly (#355-05).
Note: See Page 8, Pre-assembly of collapsible JFK
Uprights, if this step was missed.
2. Install the Upright Assembly between the Base Assemblies
(refer to section on Base Assemblies Tie-Down if required)
tighten the clamp (FIG 8) on the lower section of each side of
the Upright Assembly.
Note:Mounting the Upright Assembly on to the Base
Assemblies must be done at this time in order to
prevent the completed assembly from toppling over.
3. Loosen the Spin-Snap Lock on each side of the Upright
Assembly by turning the Spin Lock portion, round disc,
counterclockwise. Turn the handle counterclockwise until it
stops, but do not force it any further. This stop prevents the
Spin Lock from being removed.
4. Loosen the 3/8” Flat Head Screw which link the uprights to the base tube.
3/8” FLAT
HEAD SCREW
BASE TUBE
UPRIGHT END
CONNECTION BLOCK

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 16
5. Prepare to slide the Rail & Inner Tube Assembly into the Upright Assembly.
(See FIG 8) The locking holes in the Inner Tube Assemblies must face to the
outside of the Uprights. If required spin the inner tubes while holding the rail at
the rail pivots firmly. Ensure that the Inner Tubes are at right angles to the rail
and rotated to align properly with the Upright Tubes.
6. Release the Snap Lock Device on each Upright and lower the Rail & Inner Tube
Assembly into the Uprights. Pull outward on the Snap Lock Device once the
Inner Tube reaches the pin, lower the rail while releasing the Snap Lock Device
until the 1
st
inner tube hole allows the pin to fall into the locking hole of the
inner tube, the Snap Lock Device is now engaged.
Note: To avoid injury while lowering the rail into position, keep hands
well clear of the inner tubes where they slide into the Uprights.
7. Position the rail at a height that will be comfortable to work with during the set-
up of the apparatus and engage the Snap Lock Device so that the pin drops into a
hole. Tighten the Spin Lock portion securely by turning it clockwise.
8. Thread now the 3/8” Flat Head Screw to attach the uprights to the base
tube firmly.
9. If you are assembling Just for Kids Parallel Bars or Uneven Bars, repeat Steps 1
through 6 with the second Upright Assembly and Rail & Inner Tube Assembly.
Note: To avoid possible injury and/or damage to the first Rail & Inner
Tube Assembly while working with the second Upright, ensure
that the first Assembly is either mounted & locked to the Base
Assemblies or well clear of the working area and cannot be
accidentally tipped over.
3/8” FLAT
HEAD SCREW
BASE TUBE
UPRIGHT END
CONNECTION BLOCK

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 17
FIG 9
FIG 10
Just for Kids - Ring Frame to Uprights Assembly
This procedure will require at least two (2) qualified
persons. At no time should children or other unqualified
persons undertake any part of this procedure.
1. Locate one (1) Upright Assembly (#355-05).
Note: See Page 8, Pre-assembly of collapsible JFK
Uprights, if this step was missed.
2. Install the Upright Assembly between the Base Assemblies
(refer to section on Base Assemblies Tie-Down if required)
tighten the clamp (FIG 9) on the lower section of each side of
the Upright Assembly by turning Clockwise.
Note: Mounting the Upright Assembly on to the Base
Assemblies must be done at this time in order to
prevent the completed assembly from toppling over.
3. Loosen the Spin-Snap Lock on each side of the Upright
Assembly by turning the Spin Lock portion, round disc,
counterclockwise. Turn the handle counterclockwise until it
stops, but do not force it any further. This stop prevents the
Spin Lock from being removed.
4. Working with one Ring Frame at a time, prepare to slide the Ring Frame Assembly
into the Upright Assembly. (See FIG 9) The 5 locking holes in the Ring Frame
Assembly must face to the outside of the Uprights. Ensure that the Ring Frame
Assembly is at right angles to and rotated to align properly with the Upright Tubes.
5. Release the Snap Lock Device on each Upright and lower the Ring Frame
Assembly into the Uprights. Pull outward on the Snap Lock Device once the Inner
Tube reaches the pin, lower the inner tube while releasing the locking device until
the 1
st
inner tube hole allows the pin to fall into the locking hole of the inner tube,
the Snap Lock Device is now engaged.
Note: To avoid injury while lowering the Ring Frame into position, keep hands
well clear of the inner tubes where they slide into the Uprights.
6. Position the Ring Frame Assembly at a height that will be comfortable to work with
during the set-up of the apparatus and engage the Snap Lock Devices so that the pin
drops into a hole. Tighten the Spin Lock portion securely by turning it clockwise.
7. Repeat Steps 4 through 6 with the second Ring Frame Assembly.
Just for Kids -Attaching Rings to Ring Frame Assembly
1. Locate the Ring Assemblies (#355-110).
2. Open the quick links on the Ring Assemblies and mount them to
the Ring Frames. Close the quick links securely. (See FIG 10)

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 18
FIG 11
FIG 12
Changing Just for Kids Apparatus Configurations
Simply by changing the combination of uprights placed between the S/A Sport Just for Kids Base Assemblies
you can create numerous Apparatus Configurations. (See Chart on page 7)
This procedure will require at least two (2) qualified persons. At no time should children or other
unqualified personnel undertake any part of this procedure.
1. To install or remove uprights on the bases, completely loosen the Clamp Handles on
both sides of one of the Upright Assemblies by turning Counter Clockwise direction.
2. Carefully lift an Upright Assembly onto or off the bases. Always adjust the distance
between the Base Assemblies so that the inside surfaces of the upright clamp
mechanisms are tight to the Base Assemblies.
Note: Ensure that the Upright Assemblies remain square & perpendicular
to the Bases after adjusting there location on the bases.
3. Lock the Uprights in place by tightening the Clamp handle by spinning it in a
clockwise direction.
4. If you are assembling Just for Kids Parallel Bars or Uneven Bars repeat steps 1
through 3 with the second Upright Assembly.
Equipment Height Adjustment
S/A Sport recommends that two (2) qualified persons perform this adjustment. At no time
should children or other unqualified persons perform equipment height adjustments.
1. To avoid possible injury and/or damage to the equipment, support the Rail or
Ring Frame during all Inner tube height adjustments.
Note: To avoid injury while adjusting Ring Frame or Rail height, keep hands
well clear of the Inner Tubes where they slide into the Uprights.
2. Loosen the Spin-Snap Lock Device on each side of the Uprights, by turning the
Spin Lock portion, round disc, counterclockwise. (See FIG 12)
3. While supporting the weight of the Rail, Ring Frame, pull outward on the Snap
Lock Portion of the Spin-Snap Lock Devices on the Uprights. (See FIG 12)
4. Adjust the height of the rail to the desired setting by raising or lowering the rail.
Note that the height settings are in increments of 3”.
5. Release the Snap Lock Devices and lift or lower the Rail, or Ring Frame inner
tube until the Snap Lock device’s pin is engaged in the locking hole.
Note: Ensure that the Snap Lock Devices are fully engaged in a locking hole.
6. With the Snap Locking Devices fully engaged, tighten the Spin Lock Portion
securely, by turning the round disc clockwise.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 19
FIG 14
Horizontal Adjustment of Uprights
S/A Sport recommends that two (2) qualified persons perform this
adjustment. Children or other unqualified personnel should never undertake
the horizontal adjustment of the Uprights.
Always Support the uprights and installed apparatus during this adjustment!
1. Loosen the Clamp Handles on the lower out side of the Uprights, by turning in a
counterclockwise direction. (See FIG 14)
2. Slide the Uprights horizontally along both Base Assemblies into the desired position.
Note: To avoid injury while adjusting the Uprights horizontally along the
Base Assemblies, keep well clear of the clamp mechanisms.
3. Re-tighten the Clamp Handles, by turning in a clockwise direction. (See FIG 14)
SECTION III SAFETY
Warning
Any activity involving motion or height creates the possibility of serious injury including permanent
paralysis and even death from landing or falling on the neck, head or other parts of the body.
You assume the risk of serious injury in using this equipment. However, the risk can be reduced by
strictly following these rules at all times:
1. This equipment is designed and intended for use only by the beginner level gymnasts under a weight
of 150 lbs (68 kg).
2. Use this equipment only under the supervision of a trained and qualified instructor.
3. This equipment must be used only when protected by proper matting as recommended by the
Federation of International Gymnastics (F.I.G.). If in doubt, concerning proper matting, do not use
this equipment.
4. This equipment must be used with proper spotting equipment and qualified spotters suitable to the
activity or skill. Always consult an instructor.
5. Know your own limitations and the limitations of this equipment. Follow progressive learning
techniques and always consult an instructor.
6. Always inspect this equipment for proper stability before each use.
7. Always inspect this equipment for loose fittings and parts. Replace any worn, defective or missing
parts.
8. Always inspect this equipment for improper or unsafe installation. If in doubt, do not use this
equipment.

JFK Product & Installation Instructions #8920100 Feb 2, 2015 Pg. 20
SECTION IV SPARE PARTS
Note: For JFK Single locking Uprights only
JFK Spin - Snap Lock – 1 ea. Part# P355-254A
(Combination Locking Handle and Snap Lock)
Clamp Assembly – 1 ea. Part# P355-248A
(new part fits prior applications)
Fiberglass Rail with
Wood Veneer Assembly – 1 ea. Part# 355-65
- c/w mounting hardware
Inner Tube Assembly, Low Bar – 1 ea. Part# 355-62
- c/w Rail Pivot
Inner Tube Assembly, High Bar – 1 ea. Part# 355-57
- c/w Rail Pivot
Rings Assembly – 1 Pair. Part# 355-110
- Assembled complete with Quick Links
Base Foot Pad – 1 Pair Part# 355-BFP
(Black Foot Pad only, in Pairs)
Obsolete Part