Salvo S401 User manual

S401 Quick Start Guide
V1.1
All manuals and user guides at all-guides.com
all-guides.com

1
x 12
Note: 60mm x 60mm x15mm fans are
recommended. A single 60mm x 60mm x
25mm fan may be used on the bottom mounts,
but doing so will interfere with two 2.5” drive
mounts and one 3.5” drive mount.
60mm Fans (Optional)
All manuals and user guides at all-guides.com

x 4
Note: Be sure to install mainboard I/O shield
before installing mainboard.
2Mainboard
All manuals and user guides at all-guides.com

x 2
Note: Orientation of PSU is with FAN intake
face up.
3Power Supply Mounting Bracket
All manuals and user guides at all-guides.com

4Power Supply Extension Cable
All manuals and user guides at all-guides.com

x 2
5
Note: A foam anti-vibration pad has been
installed underneath the PSU retaining tab on
the chassis. Take care when installing the
PSU to ensure the foam pad is not damaged.
Before fastening the screws, please check for
any interference with the front panel button. If
you find the C14 connector makes contact with
the front button, you may choose to install the
front button spacer (black acrylic ring). Simply
remove the front panel button by unscrewing
the nut on the back, then insert the spacer on
the outside of the case and thread the button
wires back through both the spacer and the
mounting hole. Re-install the nut for the front
panel button. The spacer adds an additional
1/8” clearance.
Power Supply to Chassis
All manuals and user guides at all-guides.com
all-guides.com

x 4
6a
Note: Up to four 2.5” drives can be installed.
Use holes labeled S-1, S-2, S-3, and S-4.
2.5” Drive Install
All manuals and user guides at all-guides.com

6a 2.5” drive mount locations
All manuals and user guides at all-guides.com

x 4
6b
Note: Two 3.5” drives may be installed. Use
holes labeled H-1 and H-2.
3.5” Drive Install
All manuals and user guides at all-guides.com

6b 3.5” drive mount locations
All manuals and user guides at all-guides.com

7a
Note: Angle GPU with I/O shield down and move
toward rear chassis slot.
GPU Install
All manuals and user guides at all-guides.com
all-guides.com

7b
Note: Be sure to carefully align the PCIe tab
from the GPU to the PCIe extender and gently
insert.
GPU Install (Cont’d)
All manuals and user guides at all-guides.com

x 2
7c
Note: Tapped holes may strip if GPU screws are
over-tightened.
GPU Install (Cont’d)
All manuals and user guides at all-guides.com

x 4
8
Vented Panel Install
All manuals and user guides at all-guides.com

x 4
9
Solid Panel Install
All manuals and user guides at all-guides.com

10a
Note: Be sure orientation of the stand ensures
the key fastener aligns with the keyhole on the
chassis. Also, stands may be installed on either
end of the chassis depending on desired
orientation (vertically). If using horizontal
orientation, skip to step 11.
Stands
All manuals and user guides at all-guides.com
all-guides.com

x 2
10b
Stands (Cont’d)
All manuals and user guides at all-guides.com

11a
If the passthrough holes for the thumbscrews
are not aligned the handle needs to be rotated
180 degrees.
Note: Like the stands, the handle may be
installed on either of two surfaces of the case. If
you are using the stands, the handle must be
installed on the opposite side of the case as the
stands.
Handle (Optional Accessory)
All manuals and user guides at all-guides.com

x 2
11b
Handle (Cont’d)
All manuals and user guides at all-guides.com