Samsung CW-21Z573B User manual

Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
DIGITAL
TELEVISION
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
TELETEXT (Option)
BN68-03956A-00Eng.indd 1 2007-10-18 ¿ÀÈÄ 1:22:24

English - 2
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
Important Warranty Information Regarding Television
Format Viewing
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily
designed to view standard format full-motion video. The images displayed on them should primarily be in
the standard 4:3 ratio format and constantly moving.Displaying stationary graphics and images on screen,
such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than
15% of the total television viewing per week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed
to view wide screen format full-motion video. The images displayed on them should primarily be in
the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and
constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on
non-expanded standard format television video and programming, should be limited to no more than 15%
of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game displays,
station logos, web sites or computer graphics and patterns, should be limited as described above for all
televisions. Displaying any stationary images that exceed the above guidelines can cause uneven aging
of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture.
To avoid this, vary the programming and images, and primarily display full screen moving images, not
stationary patterns or dark bars. On television models that offer picture sizing features, use these controls
to view the different formats as a full screen picture.
Be careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a
result of format selection and use, as well as other burned-in images, is not covered by your Samsung
limited warranty.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive
DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be
available in some countries.
BN68-03956A-00Eng.indd 2 2007-10-18 ¿ÀÈÄ 1:22:24

English - 3
Symbols
☛ ➢
Press Important Note
Contents
General Information
 Important Warranty Information Regarding
Television Format Viewing .............................. 2
 Checking Parts ................................................ 4
 Control Panel ................................................. 4
 Connection Panel ............................................ 5
 Viewing the Remote Control .......................... 7
Operation
 Switching Your Television On and Off ............. 9
 Viewing the Menus .......................................... 9
 Plug & Play Feature ...................................... 10
 Viewing External Signal Sources .................. 12
 Editing Device Names ................................... 13
Channel Control
 Storing Channels Automatically .................... 13
 Storing Channels Manually ........................... 14
 Adding Channels ........................................... 15
 Sorting the Stored Channels ......................... 16
 Assigning Names to Channels ...................... 16
Picture Control
 Changing the Picture Standard ..................... 17
 Customizing the Picture Settings .................. 17
 Selecting the Picture Size ............................. 18
 Digital NR .......................................................18
Sound Control
 Sound Features ............................................ 19
 Selecting the Sound Mode (depending on
the model) ..................................................... 20
Function Description
 Time Features ............................................... 21
 Child Lock ..................................................... 22
 Language / Blue Screen / Melody ................. 23
Using the DTV Feature
 Previewing the DTV Menu System ............... 24
 Displaying Programme Information ............... 25
 Operating the DTV Menu .............................. 26
Appendix
 Teletext Feature (depending on the model) .. 36
 Troubleshooting ............................................ 37
BN68-03956A-00Eng.indd 3 2007-10-18 ¿ÀÈÄ 1:22:24

English - 4
Checking Parts
Owner’s Instructions Remote Control/
AAA Batteries
Warranty Card/Registration
Card/
Safety Guide Manual
Cloth-Clean
Control Panel
Front Panel
1 MENU
Press to see the on-screen menu of your TV’s
features.
➢ Press the MENU button in DTV mode to
display the DTV menu.
The analog menu appears when you
press the MENU button again.
To dismiss the menu, press the MENU
button once again.
2 −  +
Press to increase or decrease the volume.
In the on-screen menu, use the −  +
buttons as you use the ◄ and ► buttons on
the remote control and also use decrease and
increase buttons as the functions of return and
enter respectively.
3 C/P.
Press to change channels. In the on-screen
menu, use the C/P. buttons as
you use the ▲ and ▼ buttons on the remote
control.
4 Remote Control Sensor
Aim the remote control towards this spot on
the TV.
5 Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
6 (Power) button
Press to turn the TV on and off.
If the TV was turned off by using the POWER
button on the front panel, you will not be able
to turn on the TV by using a remote control.
➢ The product colour and shape may vary depending on the model.
BN68-03956A-00Eng.indd 4 2007-10-18 ¿ÀÈÄ 1:22:25

English - 5
Connection Panel
Side Panel
1 EXT 2(AV IN)
Video and audio inputs for external devices,
such as a camcorder or VCR.
2 Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
➢ Prolonged use of headphones at a high
volume may damage your hearing.
2
1
➢ The product colour and shape may vary depending on the model.
BN68-03956A-00Eng.indd 5 2007-10-18 ¿ÀÈÄ 1:22:28

English - 6
☛  Whenever you connect an audio or video system to your set, ensure that all elements are
switched off.
 When connecting an external device, match the colour of the connection terminal to the cable.
1 EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
Input/Output Specification
Connector Input Output
Video Audio(L/R) RGB Video + Audio(L/R)
EXT 1 ✔ ✔ ✔Only TV or DTV
output is available.
EXT 2 ✔ ✔AV output is available.
2 SERVICE
− Connector for service.
− Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
3 COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 35)
− When not inserting “CI CARD” in some
channels, “Scramble Signal” is displayed on
the screen.
− The pairing information containing a
telephone number, CI CARD ID, Host ID,
and other information will be displayed in
about 2~3 minutes. If an error message
is displayed, please contact your service
provider.
− When the channel information configuration
has finished, the message “Updating
Completed” is displayed, indicating that the
channel list is now updated.
➢ Insert the CI-Card in the direction marked
on it.
4 Connecting to an Aerial or Cable Television
Network
Connect the aerial or network input cable to
the 75 Ω coaxial socket.
To view television channels correctly, a signal
must be received by the set from one of the
sources: an outdoor aerial, cable television
network, or satellite network. If you are using
an indoor aerial, you may need to adjust it
when tuning your television until you obtain a
picture that is both sharp and clear.
Rear Panel
➢ The product colour and shape may vary depending on the model.
1
Cable Television
Network
or
4
3
2
BN68-03956A-00Eng.indd 6 2007-10-18 ¿ÀÈÄ 1:22:30

English - 7
Viewing the Remote Control
➢  This is a special remote control for the visually impaired persons, and has Braille points on the
Power, Channel, and Volume buttons.
 The performance of the remote control may be affected by bright light.
1 POWER button
(turns the TV on and off)
2 Number buttons for direct
channel access
3 One/Two-digit channel
selection
4 Channel control button
(Refer to page 15)
(Only in DTV signal)
5 Selects the TV and DTV
mode directly
6 Temporary sound switch-off
7 Volume increase
Volume decrease
8 Displays the main on-screen
menu
9 Returns to the previous
menu
! Picture effect selection
(Refer to page 17)
@ Sound effect selection
# Sound mode selection
$ Digital subtitle display
% Available source selection
^ Previous channel
& DTV menu display
* Electronic Program Guide
(EPG) display
( Next channel
Previous channel
) Exit the on-screen menu
a Control the cursor in the
menu
b Use to see information on
the current broadcast
d Picture size selection
e Automatic Power-off
f Digital NR on/off
g Turbo sound
Teletext Functions
(Refer to page 36)
5 Exit from the teletext display
(depending on the model)
8 Teletext index
0 Fastext topic selection
@ Teletext store
% Teletext mode selection
(LIST/FLOF)
^ Teletext sub page
( P :Teletext next page
P :Teletext previous page
) Teletext cancel
b Teletext reveal
c Teletext display/mix both
teletext information and the
normal broadcast
d Teletext hold
e Teletext size
Continued...
BN68-03956A-00Eng.indd 7 2007-10-18 ¿ÀÈÄ 1:22:35

English - 8
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as
shown in the figure.
2 Install two AAA size batteries.
➢  Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
 Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
➢ Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the TV. (Assuming typical TV usage, the batteries last
for about one year.)
➢ If the remote control doesn’t work! Check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
BN68-03956A-00Eng.indd 8 2007-10-18 ¿ÀÈÄ 1:22:40

English - 9
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Channel, Setup,
and Input.
2 Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
5 Press the EXIT button to exit from the menu.
Switching Your Television On and Off
The main lead is attached to the rear of the television.
1 Plug the main lead into an appropriate socket.
➢ The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the I (Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is reselected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
➢ If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
3 To switch the television off, press the I (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
4 To switch the TV on, press the I (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
Move Enter Exit
Mode : Dynamic ►
Contrast : 100
Brightness : 45
Sharpness : 75
Colour : 55
 More
Picture
BN68-03956A-00Eng.indd 9 2007-10-18 ¿ÀÈÄ 1:22:41

English - 10
Plug & Play Feature
When the television is initially powered on, several basic customer settings proceed automatically
and subsequently.
The following settings are available.
☛
If you accidentally select the wrong country for your TV, the
characters on the screen may be wrongly displayed.
☛
Any functions related to Digital TV (DVB) will only work in
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local
dealer if you can receive DVB-T signals. Although this TV set
follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not
guaranteed. Several functions may not be available in some
countries.
1 If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER button.
2 The Language menu will automatically appear after several
seconds.
3 Select the appropriate language by pressing the ▲ or ▼
button.
Press the ENTER button. The message Select Home Mode
when installing this TV at home. is displayed.
4 Press the ◄ or ► button to select SHOP or HOME, then press
the ENTER button. The message to check the connected
status of the antenna is displayed.
➢ The default selection is HOME.
➢ We recommend setting the TV to Home mode for the best
picture in your home environment.
➢ Shop mode is only intended for use in retail environments.
➢ If the unit is accidentally set to Shop mode, and you want to
return to Dynamic (Home) mode, press the Volume button
and then hold down the MENU button for five seconds on
the TV panel.
5 Make sure that the antenna is connected to the TV.
Press the ENTER button. The Country menu is displayed.
6 Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER button.
The message Some DTV functions may not be available.
Digitally Scan? is displayed.
➢ This OSD is concerned for all countries except for the
following countries: France, Germany, Italy, Netherlands,
Spain, Switzerland, United Kingdom, Austria, Sweden,
Finland, Denmark
If your country supports the DTV functions, the message is
not displayed. Then you can follow the instructions from step
12. When the local service provider does not support DTV
broadcasting but you choose a DTV supporting country, it
enters the DTV Plug & Play but DTV functions may not work
properly. When No is selected, follow the instructions from step
7 to 10. When Yes is selected, follow the instructions from step
11.
Continued...
Plug & Play
Select Home Mode
when installing this TV at home
SHOP
Move Enter Skip
HOME
Plug & Play
Check antenna input.
OK
Enter Skip
Plug & Play
Move Enter Skip
Country Belgium
France
Germany
Italy
Netherlands
Spain
Switzerland
United Kingdom
Austria
Eastern Europe
▼ More
Plug & Play
Some DTV functions may not be
available. Digital Scan?
No
Move Enter Skip
Yes
Plug & Play
Start Plug & Play
Enter Exit
OK
Plug & Play
Move Enter Skip
Română
Magyar
Polski
Русский
Български
Türkçe
Svenska
Norsk
Dansk
Suomi
English
Deutsch
Français
Nederlands
Español
Italiano
Português
Ελληνικά
Čeština
Srpski
Hrvatski
Language
BN68-03956A-00Eng.indd 10 2007-10-18 ¿ÀÈÄ 1:22:44