Semiconductor Components Industries MT9P006 User manual

©Semiconductor Components Industries, LLC, 2016
July, 2016 −Rev. 0
1Publication Order Number:
EVBUM2445/D
MT9P006I12STCUH-GEVB
MT9P006 Evaluation Board
User's Manual
Evaluation Board Overview
The evaluation boards are designed to demonstrate the features of
ON Semiconductor’s image sensors products. This headboard is
intended to plug directly into the Demo 2X system. Test points and
jumpers on the board provide access to clock, I/Os and other
miscellaneous signals.
Features
•Clock Input
♦Default −27 MHz crystal oscillator
♦Optional Demo 2X controlled Mclk
•Two Wire Serial Interface
♦Selectable base address
•Parallel Interface
•Serial LVDS Interface
•ROHS Compliant
Block Diagram
Figure 2. Block Diagram of MT9P006I12STCUH−GEVB
www.onsemi.com
EVAL BOARD USER’S MANUAL
Figure 1. MT9P006 Evaluation Board

MT9P006I12STCUH−GEVB
www.onsemi.com
2
Top View
Figure 3. Top View of Evaluation Board −Default Jumpers
VDDIO P4
FLASH P37
EEPROM P14, P15
OE_N P33
SCAN_EN P39
VAA P1
SEN_SADDR P25
STANDBY P35
VDDPLL P3
RESET Switch SW3
CLKGEN P20
VDD P5
VAAPIX P2
TRIGGER P34
ON_LED P11
Bottom View
Baseboard Connector P36
Baseboard Connector P9
Serial LVDS Connector J3
Figure 4. Bottom View of the Evaluation Board −Connector

MT9P006I12STCUH−GEVB
www.onsemi.com
3
Jumper Pin Locations
The jumpers on headboards start with Pin 1 on the leftmost
side of the pin. Grouped jumpers increase in pin size with
each jumper added.
Figure 5. Pin Locations for a Single Jumper.
Pin 1 is Located at the Leftmost Side and Increases as it Moves to the Right
Pin 1 Pins 1−4
Figure 6. Pin Locations and Assignments of Grouped Jumpers.
Pin 1 is Located at the Top-Left Corner and Increases in a Zigzag Fashion Shown in the Picture
Pins 1 and 2
Pins 3 and 4
Pins 5 and 6
Pins 7 and 8
Pins 9 and 10
Pin 1
Jumper/Header Functions & Default Positions
Table 1. JUMPERS AND HEADERS
Jumper/Header No. Jumper/Header Name Pins Description
P1 +2V8_VAA 1−2 (Default) Connects to on-board +2V8_VAA power supply
2−3External power supply connection
P2 +2V8_VAAPIX 1−2 (Default) Connects to on-board +2V8_VAAPIX power supply
2−3External power supply connection
P3 +2V8_VDDPLL 1−2 (Default) Connects to on-board +2V8_VDDPLL power supply
2−3External power supply connection
P4 +VDDIO 1−2 (Default) Connects to on-board +VDDIO power supply
2−3External power supply connection
P5 +1V8_VDD 1−2 (Default) Connects to on-board +1V8_VDD power supply
2−3External power supply connection
P11 ON_LED 1−2 (Default) Connects to on-board LED to indicate “power on”
P14, P15 EEPROM ADDR, Sel A1 Closed & A2 Open
(Default)
EEPROM Address set to 0xA8
A1 Open & A2 Open EEPROM Address set to 0xAC
A1 Open & A2 Closed EEPROM Address set to 0xA4
A1 Closed & A2 Closed EEPROM Address set to 0xA0
P20 MCLK 1−2 (Default) Master Mode on-board oscillator
2−3Master Mode Demo 2X clock

MT9P006I12STCUH−GEVB
www.onsemi.com
4
Table 1. JUMPERS AND HEADERS (continued)
Jumper/Header No. DescriptionPinsJumper/Header Name
P25 SEN_SAADR 1−2 (Default) I2C Address: 0x90
2−3 I2C Address: 0xBA
P33 OE_N 1−2 (Default) Parallel Interface
2−3Non-Parallel Interface
P34 TRIGGER 2 Snapshot Trigger
P35 STANDBY 2−3 (Default) Normal Mode
1−2Standby Mode
P37 FLASH 3 Snapshot Flash
P39 SCAN_EN 2 Snapshot scan enable
SW3 RESET N/A When pushed, 240 ms reset signal will be sent to
MT9P006
Interfacing to ON Semiconductor Demo 2X Baseboard
The ON Semiconductor Demo 2X baseboard has a
similar 26-pin connector and 13-pin connector which mate
with P9 and P36 of the headboard. The four mounting holes
secure the baseboard and the headboard with spacers and
screws.
Shorted Jumpers for Power Measurement
Different supplies to the evaluation board are provided by
trace shorted jumper, for any voltage and power
measurements. To conduct current for current measurement
on a given power rail, cut the trace between the two pins of
their respective JP, and insert an ammeter prior to powering
up the system. The figure below shows where the trace to cut
is located.
Table 2. SHORTED JUMPERS FOR POWER
MEASUREMENTS
Jumper Voltage (V)
P1 (+2V8_VAA) 2.8
P2 (+2V8_VAAPIX) 2.8
P3 (+2V8_VAAPLL) 2.8
P4 (VDDIO) 2.8
P5 (+1V8_VDD) 1.8
Figure 7. Top and Bottom View of Shorted Jumper. The Bottom
View Shows the Trace Location to Cut for Current Measurement
Cut here
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: [phone]
Japan Customer Focus Center
Phone: 81−3−5817−1050
EVBUM2445/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative