SES SAT DBPX User manual

User/Installer
Guide
Select Entry Systems

This page intentionally blank.

i
TABLE OF CONTENTS
1.0 INTRODUCTION TO SAT DBRX ............................................. 1
1.1 STANDARD FEATURES ................................................... 2
1.2 SPECIAL FEATURES ...................................................... 2
1.3 ENVIRONMENTAL CONSIDERATIONS ...................................... 2
1.4 ELECTRICAL ............................................................. 3
1.5 TECHNICAL DATA ........................................................ 3
2.0 INSTALLATION INSTRUCTIONS ............................................ 4
2.1 CONNECTING GROUND AND POWER ...................................... 5
2.2 CONNECTING TO SERIAL PORT ............................................ 6
3.0 INITIALIZATION AND PROGRAMMING ....................................... 7
3.1 INITIALIZATION ............................................................ 7
4.0 PROGRAMMING CHOICES ................................................. 9
4.1 SAT INFORMATION ....................................................... 10
4.1.1 ADD /EDIT SAT INFORMATION ....................................... 10
4.1.1A DELETING A SAT ID ................................................ 10
4.1.1B DELETING A FIELD ................................................. 10
4.1.1.1 LOCATION ......................................................... 11
4.1.1.2 NAMES ............................................................ 11
4.1.1.3 PHONE NUMBER ................................................... 12
4.1.1.4 ADDRESS .......................................................... 12
4.1.1.5 CITY ............................................................... 12
4.1.1.6 NOTE LINE 1 ....................................................... 12
4.1.1.7 NOTE LINE 2 ....................................................... 12
4.1.2 FIND LOCATION .......................................................... 13
4.1.3 SATS USED .............................................................. 13
4.1.4 PRINT SAT ID ............................................................ 14
4.1.5 PRINT LOCATIONS ....................................................... 14
4.1.6 PRINT ALL ID RECORDS .................................................. 14
4.1.7 PRINT ALL LOCATION RECORDS ......................................... 15
4.1.8 SHOW ALL SATS ......................................................... 15
4.1.9 SHOW ALL LOCATIONS ................................................... 15
TouchTone is a registered trademark of Western Electric
IBM and IBM XT are registered trademarks of International Business Machines

ii
TABLE OF CONTENTS
4.2 SYSTEM PARAMETERS ................................................... 16
4.2.1 SET CLOCK / CALENDAR ................................................. 16
4.2.2 SAT ID LENGTH .......................................................... 17
4.2.3 TONE DIAL ............................................................... 17
4.3 COMMUNICATIONS SETUP ............................................... 18
4.3.1 TERMINAL TYPE ......................................................... 18
4.3.2 RS232 BAUD ............................................................. 18
4.3.3 PROGRAM PASSWORD ................................................... 18
4.3.4 PRINT ALL DATA ......................................................... 19
4.3.5 PRINT INFORMATION ..................................................... 19
4.4 TRANSACTION BUFFER INFORMATION .................................... 19
4.4.1 VIEW LOG ................................................................ 19
4.4.2 SEND LOG ............................................................... 20
4.4.3 FIND SAT ID .............................................................. 20
4.4.4 LOG SIZE ................................................................ 20
4.4.5 CLEAR BUFFER .......................................................... 20
5.0 SERIAL PORT ............................................................ 21
5.1 PRINTER ................................................................. 21
5.2 TERMINAL ............................................................... 22
5.3 CONNECTING A PERSONAL COMPUTER .................................. 23
6.0 IBM KEYBOARD .......................................................... 24
7.0 OPERATION OF SAT DBRX ................................................ 25
7.1 RECEIVING A CALL FROM A SAT .......................................... 25
7.2 TERMINATING A CALL .................................................... 26
7.3 PLACING A CALL TO A SAT ............................................... 26
7.4 FORCING A SAT ID TRANSMIT ............................................. 27
7.5 PHONE LINE TROUBLE ................................................... 27

SAT DBRX V1.0
SELECT ENGINEERED SYSTEMS 06/93 1
SYSTEM
READY
1.0 INTRODUCTION TO SAT DBRX
The SAT DBRX is a microprocessor based proprietary receiving device that will allow
monitoring upto100SelfIdentifyingAutomaticTelephones(SAT)manufacturedbySES. Itmaintains
a small database consisting of this data:
!Location at the site.
!Name of the facility.
!Phone number of the line the SAT uses.
!Address of the facility.
!City that the facility is located.
!State that the facility is located.
!2 lines of 24 characters each for additional notes as required.
The SATDBRX willdial outeither pulse(rotary) orTouch-Tone viaprogrammingselection.
TM
While the SAT DBRX is dialing, the speaker disconnects, keeping the dialed phone number
confidential.

SAT DBRX V1.0 INSTALLATION AND USER GUIDE
2
1.1 STANDARD FEATURES:
!Memory Capacity: 100 SAT ID. (Additional capacity available).
!Event Buffer 75 transaction minimum (Additional buffering capacity available).
!Wrapping buffer.
!Printer capability (RS232 port) or Current Loop to printer
(Baud rates to printer and/or remote terminal (CRT)) 300, 600, 1200, 2400, 4800, 9600.
!Clock & Calendar.
!1 to 4 digit SAT ID.
!SAT DBRX dials out either Touch-Tone or rotary - field programmable.
TM
!SAT DBRX will mute tones in receiver during dialing.
!SAT DBRX will not accept Touch-Tone signals through the microphone.
TM
!Two line 24 digit per line LCD display, scrollable up to 9 lines.
!Non-volatile memory.
1.2 SPECIAL FEATURES
!Keypad active 5 seconds after SAT DBRX calls out.
!Crystal controlled tone detection for short burst 50 MS tone.
!Optional IBM keyboard programming.
!Standby batteries.
The (Optional) 12 volt DC .7 A/hr internal battery (B12V) will operate the SAT DBRX for a
minimum of1hourwith noACpowerapplied. ThebatteryisNOTrequiredformemorystorage. The
SAT DBRX is supplied with a 16 vac transformer that will operate the SAT DBRX and recharge the
optional internal battery.
DO NOT CONNECT ANY OTHER DEVICES TO THE BATTERY.
1.3 ENVIRONMENTAL CONSIDERATIONS
Indoor or Outdoor: The standard SAT DBRX housing is suitable for indoor installations only.
Dimensions: SAT DBRX largest outside dimensions are 16" W X 5" H X 12" D.

SAT DBRX V1.0
SELECT ENGINEERED SYSTEMS 06/93 3
1.4 ELECTRICAL
Power: TheSATDBRXuses16voltac50/60Hz.@300ma. A16vactransformerissuppliedwith
each purchase in the U.S. only. The installer may choose to provide their own 12 volt 300 ma. DC
supply. HOWEVER,ACTRANSFORMERAND DCSUPPLYCANNOT BEUSEDATTHESAME
TIME.
Ground: TheSATDBRXmustbeconnectedtoagoodearthgroundwithatleast#16ga.stranded
wire. This wire MUST be a minimum of 16 ga. connected to a ground rod or cold water pipe. The
maximum wire length is 50 feet. Surge damage protection built into SAT DBRX is diminished if
adequate earth ground is not provided.
1.5 TECHNICAL DATA
!! POWER INPUT: 16 VAC 15 VA UL LISTED TRANSFORMER (PROVIDED WITH UNIT).
!! EMERGENCY BATTERY: 12V .7 AHR GEL CELL ON CONSTANT CHARGE (OPTIONAL).
!! TELEPHONE LINE: VOICE GRADE RJ11C JACK.
!! SHIPPING WEIGHT: APPROXIMATELY 10 LBS.
!! CONSTRUCTION: FRONT PANEL: ALUMINUM
BACK BOX: ALUMINUM.
!! OPERATING ENVIRONMENT: TEMPERATURE: -20EF TO +140EF.
RELATIVE HUMIDITY: 5% - 95% NON-CONDENSING.
!! MOUNTING: DESK.
!! MEMORY TYPE: NON-VOLATILE.
!! TONE DETECTION: CRYSTAL CONTROLLED, CANDETECTSHORTBURST50MSTONE.

SAT DBRX V1.0 INSTALLATION AND USER GUIDE
4
2.0 INSTALLATION INSTRUCTIONS
NOTE THE FOLLOWING BEFORE ATTEMPTING ANY INSTALLATION:
A. Never install telephone wiring during a lightning storm.
B. Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
C. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
D. Use caution when installing or modifying telephone lines.
E. Installation of SAT DBRX requires co-ordination with your telephone company. It is
recommended that a Touch-Tone line be installed to allow much fasterdialing. If aTouch-Tone
TM TM
line is not available, the SAT DBRX can be reprogrammed to dial out pulse (rotary) signals.
F. The phone company may require the following information:
The ringer equivalence number.
The FCC registration number.
These numbers are indicated on the label on the back of the SAT DBRX.
The desired location of the telephone jack must be given to the phone company at the time
the phone line is ordered.
G. Actual installation of the SAT DBRX involves:
1) Grounding the SAT DBRX to earth ground from the terminal on the SAT DBRX.
2) Wiring thesuppliedtransformertotheterminalstriponthebackoftheSATDBRXand
plugging it into a 110 vac outlet.
3) Connecting the supplied phone line into the RJ-11C jack provided by the phone
company.
4) Connecting the optional IBM PC or XT compatible keyboard. (See Pg. 24)
5) Connecting an RS-232 serial device such as a printer or terminal to the DB-25
connector on the back of the SAT DBRX. (See Pg. 21).

SAT DBRX V1.0
SELECT ENGINEERED SYSTEMS 06/93 5
POWER POWER POWER
SWITCH FUSE CONN.
16 VAC 16 VAC
16VAC
GND
1 AMP
SLO-BLO TBS-1
TBS-2
TBS-3
Recommended wire gauge is as shown: 16 ga. up to 50 feet.
14 ga. up to 100 feet.
12 ga. up to 200 feet.
10 ga. up to 300 feet.
8 ga. up to 500 feet.
2.1 CONNECTING GROUND AND POWER
1) Connect a 16 gauge wire from the ground terminal (TBS-3) of the terminal barrier strip as shown
above to a good earth ground. Do this before connecting anything else to the SAT DBRX.
2) Connect the wires for the power connections to TBS-1 and TBS-2, as shown. Connect the other
endsofthewirestothescrewsonthesuppliedtransformer(16vac15va). Determinethegaugesize
from the table below.
In the event of a voltage surge or other electrical transient, the fuse may need to be replaced.
Replace with a 1 AMP slo-blo fuse only.

SAT DBRX V1.0 INSTALLATION AND USER GUIDE
6
TD
RD
BSY
GND
2
3
20
7
PHONE POWER POWER SERIAL POWER
LINE SWITCH FUSE PORT CONN.
SHLD
2.2 CONNECTING TO SERIAL PORT
The serial port on the back ofthe SAT DBRX is an RS-232 serial communications port. It is
configured to operate at 8 bits with 1 stop bit and no parity at baud rates from 300 to 9600 baud.
It may be connected to serialprinters, CRT terminals, PersonalComputers, or any otherdevice that
permits serial communications. Maximum distance for any cable connectedtothisportis100feet.
Baudratesmayhavetobeslowerforlongerrunsdependingonthecharacteristicsofthecableused.
Belden # 9940 is recommended for best operation.
NOTE: THE 5 PIN DIN CONNECTOR ADJACENT TO THE DB-25
CONNECTOR IS NOT A SERIAL PORT. DO NOT CONNECT DIN
CONNECTOR SERIAL DEVICES TO THIS PORT.
Since the most common use for this serial port is for a logging printer, the pinouts are
designed to permit pin for pin connection for serial printers. A DB-25M male plug to DB-25M male
plug on a ribbon cable will be sufficient in most installations. This should be readily available from
computer equipment supply houses.
For communication devices, such as terminals, a null modem connection (pin 2 to pin 3 and
pin 3 to pin 2) will be required.