Shark S2901 Series User manual

S2901 series
OWNER’S GUIDE

1 800 798-7398
WHEN USING YOUR SHARK®
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING YOUR SHARK®
MULTI-FUNCTION STEAM
POCKET MOP LITE.
DANGER OF SCALDING.
Please use caution when using the steam
mop. The steam emitted from the steam
mop is very hot.
IMPORTANT:
This appliance is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety.
Children shall not use or play with this
appliance. Close supervision is necessary
to keep appliance out of reach of children
during use and cooling.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
1. Use the system only for its intended use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance unattended
when plugged in. Always unplug the power
cord from the electrical outlet when not in
use and before servicing.
4. DO NOT allow the appliance to be used by
children. Close attention is necessary when
used near children, pets or plants.
5. Use only as described in this manual.
6 . Use only manufacturer’s recommended
accessories.
7. DO NOT use with damaged cord or plug.
8. DO NOT USE if the appliance is not
working, has been dropped, dropped into
water, damaged or left outdoors.
9. NO SERVICEABLE PARTS. Incorrect
re-assembly or repair can cause a risk of
electrical shock or injury to persons when the
appliance is used. Contact Customer Service.
10. To protect against a risk of electric shock,
DO NOT immerse the steam mop into
water or any other liquids.
11. DO NOT handle plug or steam mop with
wet hands or operate appliance without
shoes.
12. DO NOT pull or carry by power cord, use
power cord as handle, close a door on the
power cord, or pull the power cord around
sharp edges or corners. Keep power cord
away from heated surfaces.

www.sharkninjamanuals.com
26. Keep your work area well lit.
27. Store steam mop indoors in a cool, dry place.
28. To avoid circuit overload, do not operate
another appliance on the same socket
(circuit) as the steam cleaner.
29. If an extension cord is absolutely necessary,
an extension cord rated a minimum of 15
ampere, 2.08mm2(14 AWG) cord should be
used. Cords rated for less amperage may
overheat. Care should be taken to arrange
cord so that it cannot be pulled or tripped
over.
30. DO NOT leave unattended when the
system is connected to a power supply or
electrical outlet. Turn off all controls before
unplugging the unit.
31. DO NOT store unit with damp or wet
cleaning pocket attached. Never leave the
steam mop in one spot on any surface for any
period of time with a damp or wet cleaning
pocket attached as this will damage your
floors.
32. Always unplug and allow the steam mop to
cool before removing or changing mop heads.
33. Make sure that the water tank door is closed
when using the appliance.
WARNING: Your steam mop is
designed to clean hard floor surfaces that will
withstand high heat. Do not use on unsealed
wood or unglazed ceramic floors. On surfaces
that have been treated with wax or some
no wax floors, the sheen may be removed
by the heat and steam action. It is always
recommended to test an isolated area of the
surface to be cleaned before proceeding. We
also recommend that you check the use and
care instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS
1 3. DO NOT unplug by pulling on power cord.
To unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate current carrying capacity.
14. DO NOT put any objects into openings. Do
not use with any opening that is blocked.
15. DO NOT put hands or feet under the steam
mop. Unit gets very hot.
16. Use ONLY on flat, horizontal surfaces. Do
not use on walls, counters or windows.
17. DO NOT use on leather, wax polished
furniture or floors, synthetic fabrics, velvet or
other delicate, steam sensitive materials.
18. Liquid or steam must not be directed towards
equipment containing electrical components,
such as the interior of ovens.
19. DO NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this may
damage the unit or make it unsafe for use. If
you live in a hard water area, we recommend
using distilled water in your steam mop.
20. When in use, NEVER turn the appliance over
or on its side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS OR
PLANTS.
21. NEVER LEAVE THE STEAM MOP IN
ONE SPOT ON ANY SURFACE FOR
ANY PERIOD OF TIME WHEN THE
CLEANING POCKET IS ATTACHED
AS THIS WILL DAMAGE YOUR
FLOORS.
22. Carefully remove the cleaning pocket
immediately after you have unplugged and
allowed the steam mop to cool.
23. When cleaning the steam mop, unplug the
power cord from the electrical outlet and
clean with a dry or damp cloth. Do not pour
water or use alcohol, benzene or paint thinner
on the unit.
24. Extreme caution should be exercised when
using this appliance to clean stairs.
25. Never use steam mop without the cleaning
pocket attached.

1 800 798-7398
This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of electrical and electronic
equipment (WEEE).
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC
and its revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
sources. To return your used device, please use the return and collection systems or contact the
retailer where this product was purchased. They can take this product for environmental safe
recycling.
This product has no on/off switch and operates when plugged into the main supply source. Disconnect the
plug from mains after use.
Although the product is not provided with standby mode or off mode, it still fulfills the requirements of
1275/2008/EC - the directive for Eco-Design requirements since according to technical justification, it is
considered as inappropriate to provide standby and off modes when connecting to mains. To reduce energy
consumption be sure to unplug the unit after use.
IPX4
THIS MANUAL COVERS MODEL NUMBER:
S2901***** 11
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz
Power: 1250 Watts
Water Capacity: 350 ml

1www.sharkninjamanuals.com
Contents
Getting Started ....................................................................................... 2
Assembling Your Steam Mop ................................................................... 3
Using Your Steam Mop ............................................................................ 4
Using Your Carpet Glider.......................................................................... 5
Using Your Handheld Steamer.................................................................. 6
Using Your Removable Handheld Steamer with Accessory Hose ................. 7
Using Your Removable Handheld Steamer with Different Accessories.......... 8
Care of Your Steam Mop.......................................................................... 12
Troubleshooting Guide.......................................................................13
Warranties........................................................................................ 16
Thank you for
purchasing the Shark®
Multi-Function Steam
Pocket®Mop Lite.

21 800 798-7398
Getting Started
When assembling your steam mop there may be a little water in or around the water tank. This is because
we test all our steam mops 100% before you buy them, so you get a quality Shark® Multi-Function Steam
Pocket®Mop Lite.
aMop Handle
bCord Clip (XBTECLP03 or 3010FO2906)
cWater Tank Cap
dHandheld Steamer
ePower Button
fRelease Button
gTriangle Mop Head (1025SO)
hCleaning Pocket for Triangle Mop Head
(P118W or P140W or P101W or P152W or P153W)
iRectangle Mop Head (1024SOY)
jCleaning Pocket for Rectangle Head
(P129W or P119W or P102W or P154W or P151W)
kCarpet Glider (XCG3501)
o
r
x
p
q
n
lConcentrator Nozzle (3011FO2901)
mAccessory Hose (3010FO2901)
nGrout Scrubber Brush (1081SO)
oWindow Squeegee (1078SO)
pDetail Brush (3039SO3901)
qFlat Scrubber Tool (1077SO)
rFlat Scrubber All-Purpose Bonnet (P123W)
sCylinder Wand (1080SO)
tAll-Purpose Pocket for Cylinder Wand (P124W )
uDuster Pocket for Cylinder Wand (P107W)
vWedge Cleaning Tool (1079SO)
wWedge All-Purpose Pocket (P128W )
xFilling Flask (1039SO)
Tote Bag (not shown)
a
c
d
i
e
g
h
b
j
k
f
lm
st
u
vw

3www.sharkninjamanuals.com
IMPORTANT: Always make sure the mop is
UNPLUGGED from the wall when not in use.
Never fill the mop, attach the mop head, change
or remove the cleaning pocket when the mop is
plugged into the wall. To prolong the life of your
Shark®Multi-Function Steam Pocket®Mop
Lite we recommend using distilled water. Make
sure you only add water to the tank. Chemicals or
cleaning solution may damage the appliance and
could be unsafe for you and your family.
Assembling Your Steam Mop
g. 1 g. 2
STEAM MOP ASSEMBLY
1Insert the Mop Handle end with the “ “ facing
the front of the unit into the handheld steamer.
Push the mop handle in until you hear it click into
place. (fig. 1)
2Select the Rectangle or Triangle mop head and the
desired cleaning pocket. Fit one side of the pocket
onto the head first, then using the loop, pull the
pocket over the head. Attach the quick fasteners
on the top of the pocket to secure in place.
3Snap the mop head into the mop body by lining
up the groove on the back of the mop body with
the groove on the back of the mop head. Push
until you hear it latch into place. Press the release
button to remove or change the mop head.
(fig. 2)

41 800 798-7398
NOTE: Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
3Pull and twist the quick release cord holder to
unwrap the power cord completely. Plug into an
electrical outlet. (fig. 5)
4Press the power button to turn the unit on. (fig. 6)
5Clean your floors with a forward and backward
motion.
1Turn the water tank cap counter clockwise and
remove from the tank. (fig. 3)
2Use the filling flask and pour water into the tank.
Do not overfill. Replace the cap on the water tank.
(fig. 4)
IMPORTANT: Do not use on unsealed wood
or unglazed ceramic floors. On surfaces that
have been treated with wax or some no wax
floors, the sheen may be removed by the heat
and steam action. It is always recommended to
test an isolated area of the surface to be cleaned
before proceeding. We recommend that you
check the use and care instructions from the floor
manufacturer.
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
IMPORTANT: Make sure you do not use the
mop without attaching a cleaning pocket and
adding water to the tank first. When you are using
the mop for the first time, it might take longer
than the normal 30 seconds to start steaming.
Using Your Steam Mop
g. 3
g. 4
g. 5
g. 6

5www.sharkninjamanuals.com
6Use the shaggy side of the cleaning pockets to lift
up and lock away all the dirt and debris and the
scrubbing side to break up the tough stains.
(fig. 7)
7When the water tank is empty, the Steam Mop will
stop producing steam. You can refill the water tank
at any time as long as the mop is unplugged from
the outlet. Follow the instructions from page 4.
This applies to switching the mop head or cleaning
pocket as well.
NOTE: Please wait 2-3 minutes for the Steam
Mop to cool off before switching the mop head or
the cleaning pocket. Never leave the Steam Mop
with a damp/wet cleaning pocket on any floor.
8When you are done, press the power button to turn
the steam mop off.
Using Your Carpet Glider
THE CARPET GLIDER
1The Carpet Glider can be used with the
Rectangular Head to lightly steam your carpet and
area rugs. Just place the mop head with cleaning
pocket attached into the glider. (fig. 8)
2 Move the Steam Mop back and forth across a
section of the carpet. (fig. 9)
g. 7
g. 8 g. 9
The Steam Mop will not clean your carpeting or
area rugs. However, it is great for grooming and
freshening.

61 800 798-7398
Your Shark®Multi-Function Steam Pocket®Mop
Lite is designed to clean surfaces that will
withstand high heat and moisture. Do not
use on unsealed wood surfaces (especially
wooden antique furniture), unglazed ceramic
tile, painted surfaces or surfaces that have
been treated with wax, oils, varnishes, or
shellac. The sheen may be removed by the
heat, steam, and friction of the cleaning
tools. Lacquer and polyurethane coatings
provide a hard durable protective nish
that withstands moisture, but it is always
recommended to test an isolated area of the
surface to be cleaned before proceeding.
We also recommend you check the use
and care instructions from the surface
manufacturer.
When cleaning nished wood surfaces,
use broad, continuous cleaning strokes. To
prevent surface damage, avoid focusing
steam or allowing the cleaning tools to sit in
one spot for any amount of time.
Using Your Handheld Steamer
1To remove the Handheld Steamer, press and hold
down the Handle Release Button while pulling out
the handle. (fig. 10)
2To remove the mop head, press the mop head
release button and pull the mop head off.
(fig. 10)
g. 10

7www.sharkninjamanuals.com
CAUTION: Do not press the power button while
attaching or removing the Accessory Hose.
CAUTION: Do not use the Accessory Hose
without cleaning tools attached.
1First attach the Accessory Hose to the Handheld
Steamer by snapping the Accessory Hose into the
main nozzle. (fig. 11)
2Select the desired cleaning tool for use. Follow the
cleaning tool sub-assembly instructions for the
selected tool. (fig. 12)
3To remove the Accessory Hose, press and hold
down the Handheld Release Buttons. Then slide
out the Accessory Hose using the grip.
g. 11
Release
Button
Using Your Removable Handheld Steamer
with the Different Accessories
g. 12

81 800 798-7398
Using Your Removable Handheld Steamer
with the Different Accessories - cont.
g. 13
USING THE CONCENTRATOR NOZZLE
Cleaning Tip: The Concentrator Nozzle
creates direct steam spray to clean and
sanitise hard to reach nooks & crannies and
other places where germs may build up.
Use the Concentrator Nozzle to loosen and
dislodge compact dirt often found in corner
and tight places where traditional methods
and cleaning tools tend to push dirt into,
making it tough to reach and clean. Spray
direct steam and wipe clean with a wet cloth
or paper towel.
1Attach the Concentrator Nozzle by pressing the
nozzle onto the Accessory Hose until it clicks into
place. (fig. 13)
2Press the power button to start the steamer.
For effective cleaning, hold the steam output
nozzle 1-2 inches away from the surface you’re
cleaning.
CAUTION: Do not press the power button
until the Concentrator Nozzle is snapped into the
accessory hose of your Handheld Steamer.
3To remove the Concentrator Nozzle, press and
hold the accessory release button, then pull it out
of the Accessory Hose.
CAUTION: Do not press the power button while
removing the Concentrator Nozzle. Avoid touching
the tip of the Concentrator Nozzle, as this will be
very hot after steaming.
NOTE: The Handheld Steamer may continue
to emit steam for a few seconds after the power
button is pressed to turn the unit off. This is
normal, and the steaming will eventually come to
a stop.
USING THE GROUT SCRUBBER OR
DETAIL BRUSH
Cleaning Tip: The Detail Brush and the
Grout Scrubber are designed for removing
stubborn messes in hard-to-reach nooks,
corners and in grout where focused
scrubbing power may be needed. They can
loosen and dislodge compact dirt often
found in corners and tight places where
traditional methods and cleaning tools tend
to push dirt into, making it difcult to reach
and clean. Scrub with the Grout Scrubber or
Detail Brush and wipe clean with a cleaning
cloth.
1Attach the Grout Scrubber or Detail Brush by
snapping into the handle of the Accessory Hose
until it clicks into place. (fig. 14)
2Press the power button to start steaming.
3To remove the Grout Scrubber or Detail Brush,
press and hold down the Accessory release
button. Then slide out the tool out.
CAUTION: Turn the unit off before attaching or
removing the Grout Scrubber or Detail Brush.
g. 14

9www.sharkninjamanuals.com
USING THE FLAT SCRUBBER
Cleaning Tip: The Flat Scrubber is designed
for cleaning a variety of surfaces and is
exceptional on those that are large and at
including counter tops, table tops, walls
mirrors, windows, stairs, shelves and other
similar surfaces. Super absorbent microbre
bonnet loosens, lifts, and locks in dirt and
grime while sanitising at the same time.
1To attach the All-Purpose Scrubber Bonnet, place
the bonnet exterior side down on a flat surface
(lavender tab indicates the bottom of the bonnet)
and insert the top of the Flat Scrubber Tool into
the top portion of the bonnet and then pull the
bonnet over each side of the back edge.
2Attach the Flat Scrubber Tool by snapping into the
Accessory Hose until it clicks into place. (fig. 16)
3Press the power button to start steaming.
4To remove the Flat Scrubber Tool, press and hold
down the Accessory release button. Then slide
out the Flat Scrubber Tool.
CAUTION: Turn the unit off before attaching or
removing the Flat Scrubber Tool.
CAUTION: Do not use the Flat Scrubber
Tool without the All-Purpose Scrubber Bonnet
attached.
USING THE WINDOW SQUEEGEE
Cleaning Tip: To use the window squeegee,
work with the vapor jet down using top
to bottom movements. To do this without
leaving streaks, use lateral movements from
the top to the bottom of the surface.
CAUTION: Always avoid any sudden changes
in temperature to prevent breakage of cracks in
windows.
1Attach the Window Squeegee by snapping into the
handle of the Accessory Hose until it clicks into
place. (fig. 15)
2Press the power button to start steaming.
3To remove the Window Squeegee, press and hold
down the Accessory release button. Then slide
out the Window Squeegee.
CAUTION: Turn the unit off before attaching or
removing the Window Squeegee.
g. 15
g. 16

10 1 800 798-7398
g. 17
g. 19
3Attach the Cylinder Wand by snapping into the
handle of the Accessory Hose until it clicks into
place. (fig. 19)
4Press the power button to start steaming.
5To remove the Cylinder Wand, press and hold
down the Accessory release button. Then slide
out the Cylinder Wand.
CAUTION: Turn the unit off before attaching
or removing the Cylinder Wand. Always use the
Cylinder Wand with a pocket attached.
CAUTION: It is recommended that you allow the
cleaning pockets to cool off before removing them
from the Cylinder Wand to avoid possible scalding
injury.
USING THE CYLINDER WAND
Cleaning Tip: The Cylinder Wand provides
controlled cleaning and reaches into narrow
areas and around curved and contoured
surfaces for steam dusting and ne cleaning
activities. It is a great cleaning tool for in
and around sinks, bathtubs, refrigerator
doors, window sills, door jams and frames,
exhaust and intake vents, banisters, railings,
spindles, furniture, seating and more.
1Slide the Cylinder All-Purpose Pocket or Dusting
Pocket over the Cylinder Wand frame until it is
completely on. (fig. 17)
2Close the cinch by pulling on the elastic band and
sliding the locking bean to tighten. (fig. 18)
fig. 18
Using Your Removable Handheld Steamer
with the Different Accessories - cont.

11www.sharkninjamanuals.com
USING THE WEDGE CLEANING TOOL
Cleaning Tip: The Wedge Cleaning Tool
was designed for cleaning a variety of
surfaces and is exceptional on those that are
large and at, both horizontal and vertical.
Broad cleaning sides and super absorbent
microber fabrics loosen, lift, and lock in dirt
and grime while sanitising at the same time.
The wedge tip and squared edges reach
into tight areas often missed or difcult to
reach with traditional cleaning methods. The
Wedge sides concave to wrap around sink
and faucet xtures, door knobs, and other
small curved surfaces leaving them clean all
around. Multiple sides provide more surface
cleaning area and allow one to clean with
one side and nish with the other. Surface
examples for use are countertops, tabletops,
cabinets, walls, oor spot cleaning,
bathroom xtures and more.
1Slide the Wedge All-Purpose Pocket over the
Wedge Cleaning Tool frame until it is completely
on. (fig. 20)
2Close the cinch by pulling on the elastic band and
sliding the locking bean to tighten. (fig. 21)
3Attach the Wedge Cleaning Tool by snapping into
the handle of the Accessory Hose until it clicks
into place. (fig. 22)
4Press the power button to start steaming.
5To remove the Wedge Cleaning Tool, press and
hold down the Accessory release button. Then
slide out the Wedge Cleaning Tool.
CAUTION: Turn the unit off before attaching or
removing the Wedge Cleaning Tool. Always use
the Wedge Cleaning Tool with a pocket attached.
CAUTION: It is recommended that you allow the
cleaning pockets to cool off before removing them
from the Wedge Cleaning Tool to avoid possible
scalding injury.
fig. 20
fig. 22
fig. 21

12 1 800 798-7398
AFTER USE AND STORAGE
1Press the power button to turn the unit off. Unplug
the cord from the outlet and place the mop into the
upright position. Let the unit cool for 2-3 minutes.
2When you have finished using the Handheld
Steamer, reattach the handle to the handheld
steamer.
Care of Your Steam Mop
g. 23
3Remove the cleaning pockets from the mop heads
by releasing the quick fasteners and using the
loop on the side of the pocket, avoiding contact
with the hot pocket or dirt.
4Empty the water tank before storage. Remove the
water tank cap and empty the tank over a sink.
Replace the water cap.
5To store the Shark®Multi-Function Steam
Pocket®Mop Lite hanging up, first remove the
head (after it has cooled and the steam has been
released) then hang on a large hook. (fig. 23)

13www.sharkninjamanuals.com
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can build up and
impact the performance of your steam mop
over time. To extend the life of your product we
recommend that you use distilled water.
CARE OF YOUR CLEANING POCKETS
1We recommend washing your cleaning pocket
separately from other fabrics to avoid picking
up lint. For optimal cleaning performance, the
pockets may need to be washed up to (3) three
times. Only use liquid detergent (no
powder detergent). Do not use any
fabric softeners or bleach. Line dry. Do not
tumble dry. (fig. 24)
2If there are loose threads on the cleaning pocket,
carefully cut the thread with scissors. Do not pull
on them or cut at the base. (fig. 25)
IMPORTANT: The cleaning pocket may be very
hot from the steam. Use caution when removing.
Let the unit cool for 2-3 minutes.
g. 24
g. 25
g. 26
CLEANING THE NOZZLE
NOTE: To prevent clogging, it is recommended
that you periodically clean the Direct Steam Nozzle
and the extension hose stem.
1Your Handheld Steamer should not normally require
cleaning, however, should you notice a decrease in
the steam output, it may be necessary to remove
mineral deposits built up around the nozzles.
2Unplug the cleaner from the electrical outlet.
3Use a small diameter stiff metal wire, such as a
straightened metal paperclip, and carefully insert
the end of the wire into the nozzle orifice. See
illustration above. (fig. 26)
4Move the wire back and forth several times to
remove any deposits.
5Plug in the appliance to the power outlet and test
steam output.
40°

14 1 800 798-7398
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Shark®Multi-Function
Steam Pocket®Lite Mop
will not turn-on.
Your steam mop should be securely plugged into an electrical outlet only.
Check your fuse or breaker.
The unit will not make steam.
Is there water in the water tank? If not, add water to your steam mop following
instructions on page 4.
When using the unit in the handheld mode, ensure that you are holding the handheld
unit horizontally to optimise the steam output. Do not hold the handheld unit vertically
as this will impede steam production. Use the hose with your chosen accessory to
reach difficult areas and above floor cleaning whilst maintaining the horizontal position
of the handheld unit.
If the unit still does not make steam, follow the instructions on page 13 to clean the nozzle.
The Shark®Multi-Function
Steam Pocket®Lite Mop
leaves water on the floor.
Check to see if your cleaning pocket is too wet. We recommend you unplug the steam
mop and change the cleaning pocket.
Make sure the cleaning pocket is attached correctly.
The Shark®Multi-Function
Steam Pocket®Lite Mop left
a white spot on the floor.
Do not leave your steam mop on the floor with a damp or wet cleaning pocket.
If you’re using tap water, we recommend switching to distilled water.
Make sure the cap is securely on the water tank.
Floors are cloudy, streaky or
spotty after steaming.
The cleaning pocket might be dirty. Flip or change the cleaning pocket.
If you washed the cleaning pocket with powder detergent, then your pocket could be
damaged and require replacement. Replacement pockets are available at
www.sharkclean.com.
This could also be an indication of prior soap or grease residue that has accumulated
on the floor. As our steam mops use only a small amount of water, it may not be wet
enough to rinse off the accumulation that the steam is bringing to the surface. We
suggest rinsing the floor with nothing but water, letting it dry, and then steam mopping
again with a clean pocket. One or more rinses generally removes the residue.
A more stubborn case may require you to rinse the floor with a mix of one part vinegar
and two parts water.
The Shark®Multi-Function
Steam Pocket®Lite Mop is
hard to push.
Make sure the cleaning pocket is attached correctly.
Check to see if the cleaning pocket is excessively dirty. If so, replace the cleaning pocket.

15www.sharkninjamanuals.com
Notes

16 1 800 798-7398
Product Registration
Please visit www.sharkninjamanuals.com or call 1-800-798-7398 to register your new Shark®product
within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number
along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering
you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a
period of one (1) year from the date of purchase when utilized for normal household use, subject to the following
conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the
unit at our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that
has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused
by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This Limited
Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service
or alteration to the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, return the complete appliance and accessories, freight prepaid. For assistance with warranty service
options or customer support, please call our customer care and product specialists at , call 1 [phone] or
visit our website www.sharkninjamanuals.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair
or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return
freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific
obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO
Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states
do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to
state or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof
of purchase date and to attach tag to item before packing with your name, complete
address and phone number with a note giving purchase information, model number and
what you believe is the problem with the item. We recommend you insure the package (as
damage in shipping is not covered by your Limited Warranty). Mark the outside of your
package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our
products, therefore the specifications contained herein are subject to change without
notice.
**THIS WARRANTY IS FOR ALL COUNTRIES EXCEPT GERMANY**