Shenzhen S5B User manual

Handheld 3-axis Gimbal Stabilizer
S5B User Manual
*Smartphone not included

CONTENT
● Package List................................................................1
● Disclaimer and Warning.............................................2
● Safety Operation Guidelines......................................4
● Get to know the Stabilizer.........................................6
● USB Connection.........................................................8
●Mounting Mobile phone, Checking Balance..............9
●Operating .................................................................10
●Operating Mode........................................................11
●Changing Orientation................................................12
●Connection............................................. ....... ......... 13
● APP Overview……………..............................................14
● Product Specification................................................15
● Warranty Information...............................................16
● Warranty Card……………………………………….....….……….17
●Certificate Of Quality………………………….....……….………18

1
PACKING LIST
The product should be packed with following items (including this
user manual), If you are missing any items or components, please
contact your dealer immediately!
GIMBAL
STABILIZER ×1
MICRO USB
CABLE ×1
MANUAL ×1
STRING ×1

2
DISCLAIMER AND WARNING
Thank you for purchasing our Stabilizer. Before you start PLEASE read this
manual and become familiar with Gimbals’ components and operating modes
to ensure proper operation. The information contains herein affects your
safety and your legal rights and responsibility.
Failure to read and follow the instructions and warnings may result in serious
injury to you or damage to your device or property.
By using this product, you hereby signify that you have read this document
carefully and that you understand and agree to abide by the terms and
conditions herein. You agree that you are solely responsible for you conduct
while using this product and for any consequences thereof. You agree to use
this product only for purposes that are proper and in accordance with all terms,
precautions, practices, policies and guidelines our company has made and may
make available.
Our company accepts no liability for damage, injury or any legal responsibility
incurred directly or indirectly from the use of this product. The user shall
observe safe and lawful practices including, but not limited go those set forth
herein.
GLOSSARY
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product.
Warning: Procedures, which if not properly followed, may incur property
damage, grave accident, or serious injury.
CAUTION: Procedures, which if not properly followed, may incur property
damage and serious injury.
NOTICE: Procedures, which if not properly followed, may incur property
damage or minor injury.

3
DISCLAIMER AND WARNING
WARNING
Read the ENTIRE User guide to become familiar with the features of our
Stabilizer before operating. Failure to operate the product correctly can result
in damage to the product or personal property, and cause serious injury. This is
a sophisticated product. It must be operated with caution and common sense
and requires some basic mechanical ability. In-correct Use of product in a safe
and responsible manner could result in injury or damage to the product or
other property. This product is not intended for use by children without direct
adult supervision. DO NOT use with incompatible components or in any way
otherwise as mentioned or instructed in the product documents provided by
our company. This Safety Guidelines herein contain instructions for safety,
operation and maintenance. It is essential to read and follow all of the
instructions and warnings in the user manual, prior to assembly, setup or use,
in order to operate the product correctly and avoid damage or serious injury.

4
SAFETY OPERATION GUIDELINE
The Stabilizer should be used in temperatures from 0℃to 40℃.
Use of the battery in environments above 40℃can lead to a fire or explosion.
Use of battery below 0℃can lead to serious damage.
IMPORTANT BATTERY SAFETY INFORMATION
• DO NOT use any third-party or unknown accessories or batteries.
• DO NOT disassemble the battery.
• DO NOT short-circuit the battery. Short circuiting may occur when the battery touches
other metal objects.
• DO NOT charge the battery in direct sunlight.
• Always charge the battery in a designated space, away from people and animals.
• DO NOT leave a battery on prolonged charge when not in use.
• If the battery has a high surface temperature, leave it to cool before you try to re-charge
it.
• DO NOT charge the battery if the ambient temperature is below 10°C or above 45°C.
• Always use the supplied charger and observe manufacturer charging requirements.
• Battery performance is best when within normal room temperature (5°C-20°C).
• Batteries need to be charged before use.
STORAGE
1. DO NOT leave the Stabilizer near heat sources such as a furnace or heater, or expose
inside of a vehicle on hot days.
2. Store Stabilizer in dry environment, and never store the Stabilizer in any environment
with temperature of over 60℃.
3. Do not leave the Stabilizer unused for too long after it has been completely discharged
to prevent over-discharge of battery which may result in battery damage and permanent
damage.

5
SAFETY OPERATION GUIDELINE
■CAUTION:
1. The Stabilizers a high -precision control device, damaged may be caused to
stabilizer if it is dropped or subject to external force, and this many result in
malfunction.
2. Make sure the rotation of Stabilizer axes is not blocked by external force
when the stabilizer is power on.
3. 3. The Stabilizer is not waterproof or water-resistant. Prevent contacts of
any kind of liquid or clear with.
Prevent contacts of any kind of liquid or clear with.
It is recommended to use dry cloth for cleaning.
4. Protect the Stabilizer from dust and sand during use.
■NOTICE
1. Hold the Stabilizer’s Handle still in when it is powering up to ensure it starts
up successfully.
2. Make sure the batteries are fully charged before each time of use.
3. Discharge the battery to 40%~65% if it will NOT be used for over 10 days.
This can greatly extend the battery life."
4. Charge and Discharge the battery completely once every 3 months to keep it
active.

6
Get to know Stabilizer
The stabilizer is high-precision control device. Connect to APP, it has more face
tracking, time-lapse function, etc. which can offer you professional grade
video.
1. Smartphone Clamp- hold smartphone steady.
2. Pan Motor-it allow you gimbal to rotate 330 degrees horizontally
3. Battery Level Indicator- The button shows how much power is left.
0-33% “L”light on
34-66% “L”and “M”lights on
67%-100% “L”“M”“H”lights on
4. Joystick- Control movement UP/DOWN (tilt motor) and LEFT/RIGHT
5. Bluetooth Light- Blue Light is connected, Flashing is trying to connected.
6. Operation Mode indicator Light-Display current operation mode of the
Stabilizer
6.1 Light- Stabilizer in Pan & Tilt Follow Mode
6.2 Light- Stabilizer in Pan Follow Mode

7
6.3 Light- Stabilizer in Lock Mode
7. Power ON/OFF and Press 2 times to bring the Mobile phone to bring the
Mobile phone to its original position
Power ON/OFF- press and holder the button (8) for 3-4 seconds until the three
light (6.1 )(6.2)(6.3) flashes blue, than turn on (Default Mode: Pan & Tile Mode)
Mode Button- in single press to switch mode from three operation modes
8. Zoom Control- It enables your lens of camera from wide angle to a closer
shot of your subject
9. Holder Adjustment- Hold smartphone steady
10. Roll Motor- Allows the gimbal to rotate 180 degrees vertically.
11 Balance Screw- Help balance the weight of smartphone on gimbal.
12. Adjustable Arm- Pull out or push the arm back the adjustable arm until the
smartphone balance itself
13. Tilt Motor- It allow your phone to rotate 325 degree horizontally.
14. USB Power Out- Charges the smartphone directly from the gimbal
15. Micro USB Port- Allows the gimbal to recharge its battery by connecting
the Micro-USB to any standard USB outlet or phone charger
16. Shutter Button: Press once to take a picture,
17. 1/4 Thread Screw- Allow the gimbal to mounted on the device through the
/4 thread screw.

8
USB CONNECTION
IN-USE CHARGING
Connect the Micro USB Port on
the side of stabilizer's handle to a
power source SUCH AS a power
pack (not include) to extend
run-times.
MOBILE CHARGING
The USB port at the bottom of the
stabilizer handle can be used for
charging of your Smartphone
while use.
■An L-shape charging connector
is required when the Smartphone
is mounted horizontally on the
mobile clamp.

9
MOUNTING SMARTPHONE
ADJUST BALANCE
If the Smartphone does not stay leveled when mounted, please do as
following:
Step 1: Loosen the Roll balance Knob.
Step 2: Make small Adjustment by sliding the horizontal arm, until the mobile
balance almost.
Step 3: Tighten the Thumb Screw after the phone is well balanced in level to
ensure normal operations.
NOTEDS: Proper adjustment of balance ensures better power saving during
operation. The stabilizer may still function well when the gravity center is not
properly configured; however, it may lead to more power consumption on the
motors, and can greatly affect the torque output.
Place Smartphone to mounting clip as show.
Slide the Smartphone to right until it
touches Tilt Motor.

10
OPERATING
To Power On
Press & Hold the Power/Shooting button for 3-4 seconds until the Mode
Indicator light flashes blue, and then turns on All Follow Light in blue color
finally.
TO POWER OFF
Press & Hold the Power/Shooting button for 3-4 seconds until the Mode
Indicator light is off.
Power ON/OFF+
Mode Button

11
OPERATING MODES
Locking Mode：
All 3 axes are locked.
The camera keep still and
stable, which mean the
camera, cannot follow
movement of handle/
Pan Following Mode：
Tilt & Roll are locked.
Pan axis rotates smoothly
with turn of wrist.
Following Mode：
Roll axes is locked.
The camera pan and tilt
are following the
movement of camera.
SWITCHING STABLIZER MODES
a. The stabilizer enters default
Pan & Tilt Following Mode each
time when powered on.
Step 2: Click power button to
Switch into Pan Following
Mode.
Step 3: Single Press the power
button to enter into Locking
Mode
Notes:
The Joystick Function can be
used in all 3 modes.
(The any camera-position
adjustment can be manually
control by hands)

12
CHANGE ORIENTATION
1. SWITCHING FROM HORIZONTAL TO VERTICAL
Keep the phone facing yourself and rotate the Stabilizer handle over 70
degrees in counterclockwise direction, Stabilizer will enter vertical shooting
Mode. (Phone camera upward)
Keep the phone facing yourself and rotate the Stabilizer handle over 70
degrees in clockwise direction, Stabilizer enter vertical shooting. (Phone
camera upward)
2. SWITCH MOUNT DIRECTION
Step 1: Loosen the Smartphone Clamp Thumbscrew and rotate the clamp to
vertical direction
Step 2: Place your Smartphone on the Clamp
Step 3: Tighten the Clamp Thumbscrew to ensure normal operations.
Note: Please convert the phone holder when the gimbal stabilizer is turned off.

13
HOW TO DOWNLOAD APP
1.Scan QR Code (For Android +iOS) and download below APP for accessing.
2. Find the “Gimbal Pro” App on Google Play & APP Store
BLUEBOOTH CONNECTION
1. USING SMARTPHONE’S CAMERA
Step 1: Power on the stabilizer
Step 2: Turn on Bluetooth in your smartphone setting.
Step 3: Find the Bluetooth name ‘Stabilizer_xxxxxx ’to pair the Bluetooth.
3. USING APP
Step 1: Power on the stabilizer
Step 2: Turn on Bluetooth
Step 3: Get into the APP searching device, find the device name
"STABILIZER_xxxxxx", then click device name to enter the camera interface.

14
APP OVERVIEW
1. Photo & Video Switch
2. Panorama & Time-lapse
3. Shutter & Shooting
4. Toggle Camera
5. Gallery
6. Bluetooth
7. Face / Object Tracking
8. Mode Status
9. Gimbal Battery
10. Phone Battery
11. Flash
12. Home
13. Camera Modes
14. Mode Select
15. Settings

15
PRODUCT SPECIFICATION

16
WARRANTY INFORMATION
Warranty Period
1. The warranty period is 1 year from the original date of purchase.
During the warranty period, under normal use, our company will at its option,
repair and/or replace parts which determined by defective situation.
2. Warranty this product against effects in material or workmanship when it
belong Normal consumer usage and conditions for the time periods.
Warranty does not cover:
1. Products subjected to unauthorized Maintenance, misuse, collision, neglect,
mishandling, soaking, accident, and unauthorized alteration.
2. Incorrect use of product: Removing serial number labels/tags
3. Products whose warranty has expired.
4. Products damaged due to inevitable force, such as fire, flood, lighting, etc.
Warranty Claim Procedure
If failure or any problem occurs to your product after purchase, please contact
a local agent for assistant.
Latest Information
For the latest user manuals, tutorial video, firmware and calibration instruction,
please visit your dealer web page.
Many Stabilizer performances can be solved with a simple calibration
sequences.

FCC Statement

§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Specific Absorption Rate (SAR) information:
This product meets the government's requirements for exposure to radio waves. The
guidelines are based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all persons regardless of
age or health.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure
requirements, a minimum separation distance of 5mm for body worn must be maintained
between the user’s body, including the antenna. Third-party belt-clips, holsters, and similar
accessories used by this device should not contain any metallic components. Body-worn
accessories that do not meet these requirements may not comply with RF exposure
requirements and should be avoided. Use only the supplied or an approved antenna.
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation