Shinheung Engineering SPACECRAFT User manual

1
SPACECRAFT MODEL NO.
GS-SC2300FINSTALLATION MANUAL
SHINHEUNG ENG
1046-3, Najeon-ri, Saengnim-myeon,
Gimhae-si Gyeongsangnam-do, 621-821,
Re ublic Of Korea
Tel) +82. 55. 326. 9096~7
Fax) +82. 55. 326. 9022
E-mail) gswe[email protected]
Web site) www.gsweb21.com

2
SPACECRAFT MODEL NO.
GS-SC2300F
Ages: 6 to 12 years
Ca acity: 25 children
Size: D: 10‘10”/ 3.30m
H: 11' 3”/ 3.43m
Use zone: D: 30' 6”/ 9.30m
Features
The Spacecraft launches the merry-go-round into the future with
a space-age look. Children love the flying-saucer design that
helps their imaginations fly into orbit. Our special bearing
system controls the rotation speed so that the children
can safely enjoy the same exhilarating experience as
a merry-go-round.
The S-SC2300F features GS Web Technology which includes
the highest steel content and the strongest connection materials
in the industry, including a steel-wire core in our edge ropes
and connection points crushed in place with over 75 tons of
pressure to ensure long life of the games and maximum safety
for the children.
S Web Rotating Climbers help bring movement, balance,
exercise and fun back into the playground.
Figure-1: Com leted S aceraft

3
SPACECRAFT MODEL NO.
GS-SC2300FSafety area
10620
6960
3300
1525
1525
1830 1830
Figure-3: Safety area
Safety area
The requirements for space and safety clearances are taken from
BS-EN 1176-1 / ASTM-F1487 / CSA Z614
The use zone for stationary play equipment shall extend no less than
72 in. (1830mm) from all sides of the play structure.
Figure-2: Install
Protective Surfacing Zone
Non Encroachment Zone
(Required by CSA standards only)
Im erial/Metric
conversion:
48" = 1220mm
54" = 1370mm
60" = 1525mm
72" = 1830mm
130" = 3300mm
134" = 3400mm
274" = 6960mm
418" = 10620mm

4
SPACECRAFT MODEL NO.
GS-SC2300FFoundation Layout
10620
6960
1830
3300
1525
1525
4650 ( ALVANIZED POST LEN TH)
1370
1525
1220
13451955
3170 (INOX POST LEN TH)
1830
2000
3300
3430
Finished rade
255
130
330
Figure-4: Foundation layout
Im erial/Metric
conversion:
48" = 1220mm
54" = 1370mm
60" = 1525mm
72" = 1830mm
130" = 3300mm
135" = 3430mm
274" = 6960mm
418" = 10620mm
Foundation
Measure location of game and dig a
hole 5' x 5' x 4' 6" deep centered on the
center of the game.

5
SPACECRAFT MODEL NO.
GS-SC2300FOverall Assembly
Figure-5: Overall Assembly
ANGLE BRACE
LOWER NET
GALVANISED POST
BASE
LOWER RING, DECK
UPPER RING
UPPER NET
SPIDER NET
Overall Assembly
Assemble the arts in the following order:
1. Attach the upper net to the post head
2. Attach the ring to the net
3. Attach the spider net to the ring and the collar
4. Attach the lower net to the ring
5. Temporarially support the lower net by tying it to
the middle ring before lifting the assembly
6. Assemble base and angle braces
... cont'd next age
STAINLESS STEEL PAINTED POST

6
SPACECRAFT MODEL NO.
GS-SC2300FPost installation
60"
54"
12"
Figure-7
Figure-6
NYLON STRING
EYE BOLT
7. Screw the eye bolt to the top of the galvanised post
8. Lift the assembly and place in the hole, inserting the post into
the pre-assembled base.
9. Level the post and fill hole with excavated ground
10. Install the protective surface
11. Assemble the lower ring and deck, attach to lower net.
12. Attach deck to collar on the post
13. Remove eye bolt and install the cap

7
SPACECRAFT MODEL NO.
GS-SC2300FAluminium ring assembly
M8 X L33 RING FIX NUT,WASHER
M8 X L55 RING FIX BOLT
12 fasteners on the to
UPPER RING
Figure-8
NYLON JOINT
Assemble the ring at the net with the nylon joint ( 1+1, 2+2, 3+3, 4+4 )
Align the o ening in the net with the ring fasteners
4
4
11
33
2
2

8
SPACECRAFT MODEL NO.
GS-SC2300FSpider Net & Upper net Assembly
HALF ALUMINIUM RING
BALL JOINT
COLLAR
M10 NUT, WASHER
M10 X L35 HSCS BOLT
SPIDER NET
UPPER NET
BALL JOINT
Figure-9
Figure-10
Figure-11
Attach the ring to the u er net
Attach the s ider net to the ring and the collar

9
SPACECRAFT MODEL NO.
GS-SC2300FDeck assembly
Figure-12
PVC COATED FLOOR
LOWER RING
HALF COLLAR
M12 X L35 BOLT
M10 X L90 HSCS BOLT
M12 NYLON LOCK NUT,
WASHER
M8 X L33 FIX NUT
M12 NYLON LOCK NUT, WASHER
M8 X L55 FIX BOLT
M12 X L30 BOLT

10
SPACECRAFT MODEL NO.
GS-SC2300FLower net assembly
Figure-13
Figure-14
UPPER RING
Assemble net in the attach with ball joint
BALL JOINT
LOWER RING
LOWER NET

11
SPACECRAFT MODEL NO.
GS-SC2300FBase assembly
ANGLE BRACE
M12 X L35 BOLT
M12 NUT, WASHER
M12 X L35 BOLT
BASE
M12 NUT, WASHER BASE HALF COLLAR
Figure-15

12
SPACECRAFT MODEL NO.
GS-SC2300FCap assembly
BALL JOINT
M10 X L25 HSCS BOLT
POST CAP
Remove the eye bolt
Install the ca with HSCS bolt

13
SPACECRAFT MODEL NO.
GS-SC2300FParts list
1: galvanised ost
2: inox ost
3: ost ca
4: u er net
5: s ider net
6: lower net
7: aluminium ring (Φ2000)
8: aluminium ring (Φ3300)
9: PVC coated floor
10: nylon joint (Φ75)
11: nylon joint (Φ50)
12: half collar
13: half collar (deck)
14: eye bolt
15: M10 X L25 HSCS bolt
16: M10 X L35 HSCS bolt
15
24
3
23
2
4
6
5
8
11
12
14
16,18

14
SPACECRAFT MODEL NO.
GS-SC2300FParts list
7
22
17: M10 X L90 HSCS bolt
18: nylon lock nut (M10),washer
19: M12 X L30 bolt
20: M12 X L35 bolt
21: nylon lock nut (M12),washer
22: M8 X L55 fix bolt
23: M8 X L25 fix bolt
24
24: M8 X L33 fix
nut,washer
25: base
26: angle brace
27: base half collar
28: M12 X L35 bolt
29: M12 nut,washer
21
10
25
26
27
28
29
1
9
13
21
20
19
18
17

15
SPACECRAFT MODEL NO.
GS-SC2300F
15
Maintenance
A. General safety measures
On the playground there should be a sign(pictogram) giving the following information:
a) general emergency telephone number;
b) telephone number to contact maintenance personnel;
c) name of the playground;
d) address of playground; and
e) other relevant local information, if applicable.
The entry, exit and emergency paths to and from a playground, intended for use by the public and emergency services, should be accessible and
free of obstacles at all times.
NOTE Attention is drawn to local regulations.
B. Procedures
Defects that occur during operation and which put safety at risk should be corrected without delay. If this is not possible, the equipment should
be secured against use e.g. by immobilization or removal.
There should be written operational procedures covering the measures to be taken in the event of accidents, fire and the like.
Until unsafe equipment is repaired and released for use, access by the public should be prevented. Information about accidents brought to the
attention of the manager should be recorded on a form that includes the following details:
a) date and tie of accident;
b) age and sex of victim and clothing worn, Including footwear;
c) equipment involved;
d) number of children on site at the time of the accident;
e) description of accident;
f) injury sustained including part(s) of body affected;
g) action taken;
h) witness statements;
i) any subsequent equipment modification;
j) weather conditions; and
k) any other relevant information.

16
SPACECRAFT MODEL NO.
GS-SC2300F
16
Maintenance
C. Routine maintenance
To reduce accidents, the owner or operator should ensure that an appropriate routine maintenance schedule is established, implemented and
maintained. This should take into account local conditions and the manufacturer's instructions that can affect the necessary inspection frequency.
The schedule should list the components to be maintained and should also give procedures for dealing with complaints and breakdowns.
The routine maintenance of playground equipment and surfaces should consist of preventative measures to maintain their level of safety,
performance and compliance with the relevant part(s) of EN 1176. Such measures should include:
a) tightening of fastenings;
b) re-painting and re-treatment of surfaces;
c) maintenance of any impact attenuating surfaces;
d) lubrication of bearings;
e) markig of equipment to signify loose fill finished surface level;
f) cleaning;
g) removal of broken glass and other debris or contaminants;
h) restoring loose fills to the correct level; and
i)maintenance of free space areas.
D. Corrective maintenance
Corrective maintenance should include measures to correct defects, or th re-establish the necessary levels of safety of the playground equipment
and surfaces. Such measures should include:
a) replacement of fastenings;
b) welding of welding repairs;
c) replacement of worn or defective parts; and
d) replacement of defective structural components.
E. Personal safety
Repairs during operation that could put the safety of maintenance personnel of the public at risk, should be avoided.
F. Equi ment alterations
Alterations to parts of a piece of equipment or structure that could affect the essential safety of the equipment should only be carried out after
consultation with the manufacturer or a compete person.