Silencer SL-RF02 User manual

LCD REMOTE CONTROL TRANSCEIVER:
A. CHANGING THE BATTERY
BATTERY REPLACEMENT: SLRF752
The Two-Way remote transmitter is powered by one “AAA” Battery. When the power of the battery weakens
A icon shall be displayed on the LCD screen. When the old battery is replaced, there will be beep sounds to
indicate the power is back up on the transmitter.
B. STANDARD LCD ICON CONFIGURATIONS :
The lock icon will be displayed when
the door are locked.
The unlock icon will be displayed
when the door are unlocked.
Hidden Alarm Mode
The security system arm with hidden
alarm function (silent alarm)
Valet Mode
All the function shall be temporally on hold .
Door Trigger (Zone 1)
Door is illegally opened
Door Ajar
Trunk Trigger (Zone 2)
Trunk is illegally opened
Trunk Ajar or
Trunk Release
Hood Trigger (Zone 3)
Hood is illegally opened.
Hood Ajar
Shock Sensor Trigger (Zone 5)
No Icon = Shock Sensor Bypass
With Icon = With Shock Sensor
Icon Flashing = Shock Sensor trigger
Tilt Sensor Trigger (Zone 6)
No Icon = Tilt Sensor Bypass
With Icon = With Tilt Sensor
Icon Flashing = Tilt Sensor trigger

Ignition Trigger (Zone 4)
( Icon flash) Ignition switch was illegally
turned on.
System Trigger or Panic mode
Engine Cranking
Your vehicle engine cranking by remote
control.
Engine Running
Your vehicle’s engine is running
Timer Control Start
Engine starts automatically every
2 or 3 hours
Display the set up Running time
interval 2 / 3 / 24 Hours
Temperature Control Start
Engine will start at a specified temperature
Display the set up start temperature
Manual Transmission Mode
2
22
2
2
nd
Car Operation
Driver Paging
Someone is paging you from of your
vehicle.
Button Lock (Icon on)
Remote Transmission
You are transmitting the signal to control
unit.
In – Range Indicator
You are within the range of the remote
control .
Low Battery Power Save
Melody Mode Vibration Mode
Alarm Clock
Parking Meter
Reminder when time is up for parking
C. REMOTE TRANSMITTER OPERATION:
Transmitter
Button System Function Remark
Arm & Lock Doors Press the Lock button for a half second
Silent Arm & Lock Doors Press and hold for 1.0 seconds
Panic Function Press and hold for 3 seconds to Activate or
Deactivate panic function
Car Locator Press when in Armed Mode
-
Arm and Delete the
2 Stage Shock Sensor Press Twice within 3 seconds.
-
Arm and Delete the
Tilt Sensor
Press the button first then Press button
- -
Arm and Delete the
2 Stage Shock & Tilt Sensor
Press Twice then Press button within 3
seconds.
-
Arm and Hidden Alarm Function Press the button first then Press button
Disarm & Unlock Doors Press the Unlock button for a half second
Silent Disarm & Unlock Doors Press and hold for 1.0 seconds
-
Disarm & Two Steps Door Unlock (optional)
Press twice within 3 seconds

1.0sec. -
Silent Disarm & Two Steps Door Unlock Press and hold the button for 1.0 seconds first
then press button.
Trunk Release (Aux 1) Press and hold for 3 seconds
-
Passive Arming By-Pass While the system is disarmed
Activate or Deactivate the Remote Start Press button once.
- Press twice if set to start safety mode.
Running Time Extender Press and hold for 2 seconds
-
Timer Start Press the button first then tap Press button.
+
Turbo Mode Press together & release.
+
Aux 2 Timer Output Press together & release.
+
Aux 3 Timer Output Press together & release.
+
Aux 4 Timer Output Press together & release
+
Switch Code for 2nd Car Operation Press together & release.
+
Shutdown Diagnostic Press together & release
Level Setting. Press and release F button once.
Light up LCD indicator & Function Setting Press and hold for 1.0 seconds
F
FF
F
LCD Remote Program Setting Press and hold for 3.0 seconds
D. LCD TRANSCEIVER REMOTE CONTROL:
1. Press the Fbuttons the number of times corresponding to the Level you wish to select; the LCD will display LEVEL
number ( )
2. Press the button while LEVEL number text is still on to perform the command.
Button Direct Access Fx 1 Level 1 Fx 2 Level 2 Fx 3 Level 3
Arm & Lock Arm & Bypass the
Shock Sensor Arm & Bypass the Tilt Sensor Hidden Alarm
1 sec.
Silent Arming Vehicle’s
Status Check Temperature Check
Disarm & Unlock or
Silent Disarming Remote Valet ON / OFF
Car 1 / Car 2 operation Voltage Check
Trunk Release
(Aux 1) Aux 2 Aux 3
Aux 4
Remote Start or
Running Time Extender
Timer Start ON / OFF Daily Timer Start
ON / OFF
F 1 sec
Melody /
Vibration Mode Power Save Mode ON / OFF Button Lock ON / OFF
Vehicle’s Status Check: Press F button first then press and hold buttons for 1 second. The LCD remote transceiver
will display the current status of the vehicle.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.