SIP 01962 User manual

Universal Saw Stand
SIP Code 01962
Please read and fully understand the instructions in
this manual before operation. Keep this manual
safe for future reference

GENERAL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury. Save all warnings and instructions for
future reference.
The warnings, precautions, and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator. Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
1
IMPORTANT SAFETY INFORMATION
i) DO NOT operate or assemble the product until they have read this manual and have
developed a thorough understanding of how it works.
ii) Be careful when folding or unfolding legs to prevent any finger pinch points.
iii) Place the stand on a flat and level surface to avoid rocking or tipping of the tool.
iv) Test the setup for stability before starting work.
v) Be sure the mitre saw is tightened securely at all mountings before use.
vi) This stand is designed for use on mitre saws with a blade diameter not larger than 12
inch.
vii) Do not apply an unbalanced load which could cause the miter saw stand to tip over.
SAVE THESE WARNINGS
Danger / Caution: Indicates risk of personal injury and/or
the possibility of damage.
SAFETY SYMBOLS USED THROUGHOUT THIS MANUAL
Note: Supplementary information.
SAFETY INSTRUCTIONS

SPECIFICATION
19. 5k g
Model
SIP Code
Sa w Height
Table Rail Length
Roller Height
Leg Spa cing
Ma x Weight Ca pa city
Net Weight
GrossWeight
Pa cka ged Dimensions
Universa l Sa w Sta nd
01962
865mm
1390 - 2420mm
875 - 1030mm
550 x 1225mm
300kg
18.5kg
1330 x 270 x 180mm
2

PARTS AND ASSEMBLY
3
ABC
D
G
E
F
H
1.. Attach the legs:
A
G
ASSEMBLY

4
ASSEMBLY
Mount the mitre saw to the brackets, and then mount the brackets to the mitre saw stand. Pay
attention to the order of mounting the brackets.
3.. Fit Mitre Saw Brackets D
2.Fit Side Extensions & Roller Supports:
B
C
H
H

PARTS AND ASSEMBLY
4.. Fit Mitre Saw Bracket Supports
E
F
Mount the mitre saw to the brackets, and then mount the brackets to the mitre saw stand. Pay
attention to the order of mounting the brackets.
5

6
IMPORTANT SAFETY INFORMATION

GUARANTEE
PLEASE READ THE FOLLOWING CAREFULLY
Note: Proof of purchase will be required before any warranty can be honoured.
GUARANTEE
The SIP Universal Saw Stand is covered by a 12 months parts and labour warranty covering
failure due to manufacturing defect.
This does not cover failure due to misuse or using the stand outside the scope of this manual.
Any claims deemed to be outside the scope of the warranty may be subject to charges
including, but not limited to parts, labour and carriage costs.
Consumables items are not covered by the warranty.
In the unlikely event of warranty claims, contact your distributor as soon as possible.

7
NOTES

6
SAVE THESE INSTRUCTIONS
Please dispose of packaging for the product in a responsible manner.
It is suitable for recycling.
Help to protect the environment, take the packaging to the local
amenity tip and place into the appropriate recycling bin.
Never dispose of electrical equipment or batteries in with your domestic
waste. If your supplier offers a disposal facility please use it or alternatively
use a recognized re-cycling agent.
This will allow the recycling of raw materials and help protect the
environment.
FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR, OR SIP DIRECTLY ON:
TEL: [phone]
EMAIL: [email protected] or [email protected]
www.sip-group.com