Triton MSA200 Quick guide

MSA 200
MultiStand
MSA200
Multipurpose,adjustablesupportstandwithextrawidetripodbaseforexcellentstabilityonlevelorunevenground.Foldsdowninsecondsfor
convenienttransportationandstorage.Swivellingandtiltingheadwithbuiltinclampandlowfrictionslidesurfaces.
Multipurposesupportstandwithextrawidetripodbaseforexcellentstabilityonlevelor
unevenground
Tilting,swivellingheadfeaturesanopenUchannelcombinedwithbuiltinclampingsystem
Heightquicklyadjustsfrom635mm940mm/25"37"
Supports100kg/220lbs
Headpivotsfromhorizontaltovertical
TechnicalSpecification
ProductHeight 1070mm
ProductLength 800mm
ProductWidth 800mm
ProductWeight 5.3kg
CapacityMaximumload 100kg
HeightRange 635940mm
StandingSizeHeight 635mm
AngleAdjustmentRange Verticalthoughto
horizontal
What'sintheBox
1xHead385mm
1xAdjustablelegsupport
2xSwivel/tiltguides
4xPlasticwingnuts
1xRoundplasticwingnut
1xM8bolt80mm
1xM8bolt65mm
4xDomecrossheadscrews
1xWasher25mm
2xWasher20mm
1x40mmplate
1xInstructionmanual

tritontools.com
MSA 200
Multi-Stand
Operating and
Safety Instructions
Bedienings- en
veiligheidsvoorschriften
Instruções de
Operação e Segurança
Instructions d’utilisation
et consignes de sécurité
Instrukcja obsługi
i bezpieczestwa
Gebrauchs- und
Sicherheitsanweisung
Инструкции по эксплуатации и
правила техники безопасности
Istruzioni per l’uso
e la sicurezza
Kezelési és
biztonsági utasítások
Instrucciones de
uso y de seguridad
Provozní a
bezpečnostní pokyny
Prevádzkové a
bezpečnostné pokyny
Çalıma ve
Güvenlik Talimatları
330090_Z1MANPRO1.indd 2 03/03/2016 16:20

2
GB
12
3
4
5
6
8
9
7
330090_Z1MANPRO1.indd 2 03/03/2016 16:20

3
GB
Page 3
A
L
C
D
B
M
J
K
F
E
G
H
I
(I)
(II)
(III)
(IV)
(Fig. A)
330090_Z1MANPRO1.indd 3 03/03/2016 16:20

4
GB
Safety Instructions
Carefully read and understand this manual and any label attached to the tool before use.
Keep these instructions with the product for future reference. Ensure all persons who use this
product are fully acquainted with these instructions.
Even when following these instructions it is not possible to eliminate all residual risk factors.
Use with caution. If you are at all unsure of the correct and safe manner in which to use this
tool, do not attempt to use it.
• Do not force, or attempt to use a tool for a purpose for which it was not designed
• This tool is not intended for industrial use
• The use of any attachment or accessory other than those mentioned in this manual could
result in damage or injury.
• The use of improper accessories could be dangerous, and may invalidate your warranty
• Where possible, always secure work. If appropriate use a clamp or vice, it will allow you to
use both hands to operate your tool
Multi-Stand Safety
• AlWAYS ensure that the stand’s legs are correctly extended, and that all clamping screws
are fully tightened before applying heavy loads
• NEVER load the stand off-centre or in a manner that will cause an imbalance
• NEVER exceed the maximum load capacity (see ‘Specification’). Doing so will damage
your stand and may cause serious injuries
• DO NOT stand on this product
• DO NOT use this product for the construction of work platforms
• ALWAYS use a packing piece when clamping materials of less than 30mm thickness
• When clamping easily damaged materials, eg doors, use thin packing on both sides to
avoid damage
• Ensure the stand is securely fastened down when applying non-vertical loads or when on
sloping ground
Product Familiarisation
1. Tilt Head
2. Low-Friction Surfaces
3. Workpiece Clamping Screw
4. Tilt Head Clamping Screw
5. Column
6. Height Adjustment Clamping Screw
7. Rubber Coated Feet
8. Tripod Legs
9. Head Channel
Intended Use
• This Triton Multi-Stand is a portable tripod workpiece support suitable for a multitude of
different applications
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool
Before Use
Assembly
• The Triton Multi-Stand is easily assembled following the steps below:
1. Fold the legs of the Main Body Assembly (A) fully outwards. Loosen the round knob and
extend the stem upwards, then tighten
Note: The legs should pivot firmly. Adjust the nuts on the leg pivot bolts if necessary.
2. Fit the Saddles (B) to the stem using the locating pins on the Saddles as shown
3. Attach the Front Quadrant (C) and Rear Quadrant (D) using the shorter Hex Bolt (E), Small
Washers (F) and Lock Nut (G).
WARNING: Do not over-tighten.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Read instruction manual
Caution!
DO NOT use as a step or platform!
Description of Symbols
Thank you for purchasing this Triton tool.This manual contains information necessary for safe
and effective operation of this product. This product has unique features and,
even if you are familiar with similar products, it is necessary to read this manual carefully
to ensure you fully understand the instructions. Ensure all users of the tool read and fully
understand this manual.
Original Instructions
Introduction
Model number: MSA200
Max. load capacity: 100kg (220lbs)
Max. clamping capacity (jaw width): 51mm (2")
Min. clamping width
(min. workpiece thickness):
31mm (17⁄32")
Min. height: 635mm (25")
Max. height: 940mm (371⁄64")
Clamping width (head length): 385mm (155⁄32")
Tilt angle: 0-90°
Folded dimensions (L x W x H): 185 x 150 x 950mm
(79⁄32" x 529⁄32" x 3713⁄32")
Weight: 6.2kg (13.7lbs)
Ref. Description Dimensions Amount
AMain Body Assembly 1
B Saddles 4
C Front Quadrant 1
D Rear Quadrant 1
E Hex Bolt M6 x 60mm 1
FSmall Washer 2
G Lock Nut M6 1
HLarge Washer 1
IQuadrant Washer 1
J Hex Bolt M6 x 80mm 1
K Round Knob & Nut M6 1
LHead Assembly 1
M Pan Head Bolt 4
Specification
Component List
330090_Z1MANPRO1.indd 4 03/03/2016 16:20

5
GB
4. Fit the Quadrant Washer (I) onto the longer Hex Bolt (J) with the hex head located in the
tabs on the washer. Insert the bolt through the slots in the quadrants, ensuring that it
passes through the washer held within each quadrant and the hole in the lower stem
saddles. Fasten the Large Washer (H) onto the bolt with the Round Knob & Nut (K)
5. Rotate the quadrants until the flat tops are horizontal then gently loosely tighten the Round
Knob
6. Fasten the Head Assembly (L) to the quadrants using the Pan Head Bolts (M). The round
knob on the clamp which is built into the head should be on the same side as the round
knob on the quadrant
7. Adjust the nut tension on the Hex Bolt (E) if necessary.The head should pivot firmly, and
should lock tightly at any selected angle when the quadrant knob is tightened
Folding and Unfolding
• The Triton Multi-Stand quickly and easily folds for convenient storage (Image I):
1. Loosen the Height Adjustment Clamping Screw (6)
2. Slide the Column (5) in as far as it goes, and tighten the Height Adjustment Clamping
Screw
3. Loosen the Tilt Head Clamping Screw (4), tilt the Tilt Head (1) into the vertical position
4. Fold in all three Tripod Legs (8)
Note: To unfold the Triton Multi-Stand, follow the above steps in reverse order.
Operation
Positioning and Adjusting
WARNING: Always use theTriton Multi-Stand in a stable position. If the ground is uneven or
sloping, the stand must be secured to the ground by using suitable fasteners, such as screws,
nails or pegs, through the holes in the Rubber Coated Feet (7).
• The Triton Multi-Stand features a Tilt Head (1) that can be adjusted horizontally (0°),
vertically (90°), or in any angle between 0 and 90°:
1. Loosen the Tilt Head Clamping Screw (4)
2. Adjust the Tilt Head (1) into the required position
3. Tighten the Tilt Head Clamping Screw
Clamping
• The inside surface of the Tilt Head (1) features an adjustable serrated clamp that can be
used to hold a workpiece:
1. Loosen the Workpiece Clamping Screw (3) to adjust the serrated clamp, so it fits the
workpiece
2. Insert the work piece into the Head Channel (9) and close the Workpiece Clamping Screw
tightly (Image II)
WARNING: The serrated clamp may leave an imprint on the workpiece when clamping. Use
a shim or thin spacer between the serrated clamp and the workpiece, to keep it in pristine
condition.
Use as Sliding Work Support
• TheTriton Multi-Stand can be used as an infeed or outfeed support, sliding the workpiece
over the horizontal low-friction surface of the Tilt Head (1)
• Where additional height is needed, clamp an object with smooth surface, e.g. a piece of
wood, into the Tilt Head (as described in ‘Clamping’), to extend the height of the Triton
Multi-Stand, (Image III)
Building Work Supports
• Two or more Triton Multi-Stands can be used to build a variety of customised work
supports, (Image IV)
Accessories
• Visit your Triton dealer and www.tritontools.com to see the full range of Triton work
supports and precision power tools
Maintenance
• Inspect the Triton Multi-Stand before every use. DO NOT use if any kind of damage is
detected (deformation, corrosion, damaged welds etc.). The device may not be fit for
service and needs to be inspected by a qualified Triton technician
• Clean the body of the Triton Multi-Stand with a soft brush or dry cloth
• If the Triton Multi-Stand has become wet, dry thoroughly before storage
• From time to time, or after contact with water, the clamping screws, column and tilting
mechanism should be lightly lubricated with a suitable maintenance spray
Storage
• Store the Triton Multi-Stand carefully in a secure, dry place out of the reach of children
Guarantee
To register your guarantee visit our web site at www.tritontools.com* and enter
your details.
Your details will be included on our mailing list (unless indicated otherwise) for
information on future releases. Details provided will not be made available to any third
party.
Purchase Record
Date of Purchase: ___ / ___ / ____
Model: MSA200 Retain your receipt as proof of purchase art pr
Triton Precision Power Tools guarantees to the purchaser of this product that if any part
proves to be defective due to faulty materials or workmanship within 3 YEARS from the
date of original purchase, Triton will repair, or at its discretion replace, the faulty part free
of charge.
This guarantee does not apply to commercial use nor does it extend to normal wear and
tear or damage as a result of accident, abuse or misuse.
* Register online within 30 days.
Terms & conditions apply.
This does not affect your statutory rights oves to be defecti
330090_Z1MANPRO1.indd 5 03/03/2016 16:20