SMC Networks D-M9K/D-7K/D-RK Series User manual

No workpiece
Small workpiece
Large workpiece
Medium workpiece
Small workpiece
Square groove
Round groove
Rail groove
Medium workpieceLarge workpiece
Adjustable by trimmer
Adjustable by trimmer
OUT2 Detecting range
Output ON = Orange light is ON.
OUT1 Detecting range
Output ON = Green light is ON.
Operating range of sensor (Red light of the sensor unit is ON.)
With one switch, various sized work pieces
can be detected by the difference of
0.5 mm or more.
∗From 0.5 mm to detectable width
dependant on applied
actuator.
0.5 mm
Minimum adjustment
width to detect
OUT2 Trimmer
OUT1 Trimmer
One auto switch allows work pieces to be distinguished easily.
Direct mounting (Round groove)
type newly added
Green light is ON. Red light is ON. Green light is ON. Orange light is ON. Orange light is ON.Red light is ON. Red light is ON.
OUT1 and OUT2 are
adjustable separately.
Trimmer Auto Switch
CAT.NAS20-180C
Series D-M9K/D-7K/D-RK
Direct mounting (Round groove)
type newly added

Low
Optimum
High
Can be mounted on a standard actuator.
Direct mounting (Round groove, Square groove)/Rail mounting
IP67 (Sensor unit)
IP40 (Amplifier unit)
Applicable to the short stroke
cylinder.
Only one auto switch can detect the extended
and retracted end positions.
This switch can be used when two auto switches
cannot be mounted due to short stroke.
Examples
For checking height of a workpiece For checking depth of the machined hole
Sensor Unit
Amplifier Unit
Series D-M9K/D- 7K/D-R K Trimmer Auto Switch
Direct
mounting
DIN rail
mounting
Joining of connector
(e-con connector)
Sensor and amplifier can
be connected without
restriction.
OUT1
Green light is ON.
OUT1
Green light
is ON.
OUT2
Orange light is ON.
OUT2
Orange light
is ON.
1

Trimmer Auto Switch
D-M9K/D-7K/D-RK
Specifications
Sensor Unit
Auto switch model D-M9K D-Y7K D-F7K
Mounting
Direct mounting (Round groove) Direct mounting (Square groove) Rail mounting
Applicable amplifier unit
D-RNK, D-RPK
Indicator lamp
Red lights ON at sensitive position. Green lights ON at optimum detecting position.
Electrical entry Grommet
Impact resistance 980 m/s2
Insulation resistance
50 MΩor more (500 VDC measured via megohmmeter) between lead wire and case
Withstand voltage
1000 VAC for 1 minute (between lead wire and case)
Ambient temperature 14 to 140°F (−10 to 60°C)
Enclosure IP67
Weight (with connector)
55 g 58 g
Standard CE Marking
Oilproof Heavy-duty Cable
Auto switch model D-M9K D-Y7K D-F7K
Sheath Outside diameter [mm] ø3.5
Insulator Number of cores 4 cores (Brown/Blue/Black/White)
Outside diameter [mm] ø1.0
Conductor Effective area [mm2]0.15 (AWG26)
Strand diameter [mm] ø0.08
Min. bending radius [mm] (Reference value)
21
Note) The connector for sensor (e-con connector) is not attached to the lead wire.
It will be supplied loose in the same shipment (1 pc.).
Amplifier Unit (with Sensor Unit) PLC: Programmable Logic Controller
Model D-RNK D-RPK
Applicable sensor unit D-M9K, D-Y7K, D-F7K
Application For relay and PLC
Power supply voltage 12 to 24 VDC
Current consumption 40 mA or less
Output specification
NPN open collector 2 outputs PNP open collector 2 outputs
Load voltage 28 VDC or less —
Load current 80 mA or less/1 output
Internal voltage drop 1.5 V or less
Leakage current 100 µA or less/1 output
Response time 1 ms or less
Indicator lamp
READY: Red lights ON when the piston
position detected (with sensor unit).
OUT1: Green lights ON when turned ON.
OUT2: Orange lights ON when turned ON.
Electrical
entry
Connection to sensor
e-con connector
Power supply/output cable
Grommet
Impact resistance 98 m/s 2
Insulation resistance
50 MΩor more (500 VDC measured via megohmmeter) between lead wire and case
Withstand voltage
1000 VAC for 1 minute (between lead wire and case)
Ambient temperature 14 to 140°F (−10 to 60°C)
Enclosure IP40
Weight 70 g
Standard CE Marking
Oilproof Heavy-duty Cable
Model D-RNK D-RPK
Sheath Outside diameter [mm]
ø3.5
Insulator Number of cores 4 cores (Brown/Blue/Black/White)
Outside diameter [mm]
ø1.0
Conductor Effective area [mm
2
]0.15 (AWG26)
Strand diameter [mm] ø0.08
Min. bending radius [mm] (Reference value)
21
Internal Circuit
Sensor Unit Amplifier Unit
D-M9K/D -7K
SOUT1
Black
SOUT2
White
GND
Blue
Vsw
Brown
Main circuit
of switch
Detective
sensor
DC (−)
Blue
Black
White
Brown
1: SOUT1
2: GND
3: SOUT2
4: Vsw
+
−
DC (−)
OUT2
OUT1
DC (+)
Blue
White
Black
Brown
Blue
Black
White
Brown
+
−
12 to 24 VDC
12 to 24 VDC
OUT2
OUT1
DC (+)
OUT2
Main circuit
of switch
READYOUT1
OUT2
1: SOUT1
2: GND
3: SOUT2
4: Vsw
Main circuit
of switch
READYOUT1
Blue
White
Black
Brown
Sensor
Load
Load
Sensor
Load
Load
D-RPK
D-RNK
Connector for sensor
(e-con connector)
Direct mounting
(Round groove)
Direct mounting
(Square groove) Rail mounting
2

Series D-M9K/D-7K/D-RK
3
Applicable Actuators and Operating Range (Angle)
Sensor Unit D-M9K
Air Grippers (The operating range for grippers is measured when both ends are open.) (mm)
Description/Series Bore size
10 16 20 25 32 40 50 63 80 100 125
Parallel style MHZ2 —3.0 5.5 6.5 8.0 7.5 —————
Parallel style MHZJ2 —3.0 5.5 6.5 ———————
Parallel style MHS2 (2 fingers) — — 4.0 4.0 ∗———
Parallel style MHS3 (3 fingers) — — 5.0 4.0 ∗
Parallel style MHS4 (4 fingers) — — 5.0 3.0 ∗———
Air Cylinders (mm)
Description/Series Bore size
12 16 20 25 32 40 50 63 80 100 125 140 160 180 200
Compact cylinder CQ2-Z 3.5 4.5 4.5 5.0 5.5 5.0 5.0 6.0 6.0 6.0 7.5 7.5 8.0 7.0 7.0
Compact cylinder guide rod type CQM 3.5 4.0 4.5 4.5 5.0 5.0 5.0 6.0 5.5 6.0 —————
3 position cylinder RZQ ————5.0 5.0 5.0 5.5 ———————
Rotary clamp cylinder MK-Z 3.0 3.5 3.5 4.0 4.5 4.0 4.5 4.5 ———————
Compact guide cylinder MGP-Z 3.5 5.0 4.5 5.0 5.5 5.5 5.5 5.5 5.5 5.5 —————
∗ 1 When using the MHS series (bore size ø32 or more), use the D-Y7K.
The operating ranges are provided as guidelines including the hysteresis and
are not guaranteed value. Please consult with SMC for alternative actuators
other than those shown below.
Sensor Unit D-Y7K
Air Grippers (The operating range for grippers is measured when both ends are open.) (mm) or (°)
Description/Series Bore size
10 12 16 20 25 32 40 50 63 80 100
Parallel style MHZ2 3.0 —5.0 7.0 7.0 8.0 8.5 ————
Parallel style MHZL2 6.0 —7.0 10.0 11.0 ——————
Wide type MHL2 7.0 —8.0 8.5 10.5 11.0 12.5 ————
Parallel style MHS2 (2 fingers) —————6.5 7.0 7.5 8.5 — —
Parallel style MHS3 (3 fingers)/MHS(L)3 —————6.5 7.0 7.5 8.0 — —
Parallel style MHS4 (4 fingers) —————6.5 7.0 7.5 8.5 — —
Angular style MHC2
30° to −10°
—
30° to −10° 30° to −10° 22.5° to −10°
——————
180° Angular style MHW2 ———
88° to −5° 54° to −6° 58° to −5° 41° to −5° 30° to −4°
———
Air Cylinders (mm)
Description/Series Bore size
10 12 16 20 25 32 40 50 63 80 100
Compact guide cylinder MGP —3.5 5.0 4.5 4.5 5.5 5.5 5.5 5.5 5.5 6.0
Non-rotating double power cylinder
MGZ ——————5.5 6.5 6.5 — —
Air cylinder CA2 ——————4.0 4.0 6.0 6.0 6.0
Sensor Unit D-F7K
Air Cylinders (mm)
Description/Series Bore size
10 12 16 20 25 32 40 50 63 80 100 125 140 160
Air cylinder CJ2 4.0 —4.5 ———————————
Air cylinder CM2∗2———3.5 3.5 3.5 3.5 ———————
Compact cylinder CQ2∗34.5 4.5 5.5 5.5 5.0 5.5 5.5 5.5 6.0 5.5 6.0 7.5 7.5 7.5
Plate cylinder MU ————5.5 6.5 6.5 6.5 6.5 —————
Rotary clamp cylinder MK/MK2 ———5.0 5.0 6.5 6.0 6.0 6.5 —————
∗ 2 Use the Made-to-Order product (-XC13: Auto switch rail mounting type) for the CM2 series.
∗ 3 Not applicable to the CQ2-Z series.

Dimensions
Sensor Unit
D-M9K D-Y7K
Amplifier Unit
D-R K
Trimmer Auto Switch D-M9K/D-7K/D-RK
OFF SET
ADJ
OUT1 OUT2 READY
5
2
26 3000
ø3.5
8.8
3.1
3.95
10.8
(2.5)
5.8
6 Most sensitive position
2.5
6.2
M2.5 x 4L
Slotted set screw
33 30002
ø3.5
5
10.6 0.4
12.5 Most sensitive position
15
47
8ø3.2
ø3.5
300023 4.6
11 1
8.5 Most sensitive position
6.2 3.2
8.6
12
7.7
2.6
12.5 56 5 3000
ø3.5
DIN rail (35 mm width)
Supplied by users.
2 x ø3.5
21.1
6
30
Connector for sensor
e-con
546
ø2.0
Mounting thread M2.5 x 12L
Hexagon socket head cap screw
4
(mm)

Series D-M9K/D-7K/D-RK
5
How to Mount and Move the Auto Switch
D-M9K Mounting Bracket Direct Mounting Type
D-Y7K Mounting Bracket Direct Mounting Type
<Applicable auto switch>
Solid state ······ D-M9K
<Applicable auto switch>
Solid state ······ D-Y7K
How to Mount and Move the Auto Switch
How to Mount and Move the Auto Switch (1)
How to Mount and Move the Auto Switch (2)
Hexagon socket
head cap screw
(M2.5 x 12L)
Auto switch
Note) The tightening torque for a hexagon socket head cap screw
(M2.5 x 12L) is 0.07 to 0.15 lbf·ft (0.1 to 0.2 N·m).
1. Insert the auto switch into the mounting groove and set it at the
auto switch mounting position.
2. After reconfirming the detecting position, tighten the mounting
screw to secure the auto switch.
3. Modification of the detecting position should be made in the
condition of 1.
1. After picking up a switch spacer between your fingers, push it in
the cylinder tube groove.
2. Confirm that it is set in the correct mounting orientation.
Correct Incorrect
3. Insert the auto switch into the mounting groove and set it at the
auto switch mounting position.
4. After reconfirming the detecting position, tighten the mounting
screw to secure the auto switch.
Auto switch
mounting screw
Auto switch
Switch spacer
BMP1-032
Auto switch
mounting screw
Auto switch
Applicable Actuators
Air Grippers
Description Series Bore size
Parallel style MHZ2 16 to 40
Parallel style MHZJ2 16 to 25
Parallel style MHS2 (2 fingers) 20, 25
Parallel style MHS3 (3 fingers) 20, 25
Parallel style MHS4 (4 fingers) 20, 25
Air Cylinders
Description Series Bore size
Compact cylinder CQ2-Z 12 to 200
Compact cylinder guide rod type
CQM 12 to 100
3 position cylinder RZQ 32 to 63
Rotary clamp cylinder
MK-Z 12 to 63
Compact guide cylinder MGP-Z 12 to 100
Applicable Actuators
Air Grippers
Description Series Bore size
Parallel style MHZ2 10 to 40
Parallel style MHZL2 10 to 25
Wide type MHL2 10 to 40
Parallel style MHS2 (2 fingers) 32 to 63
Parallel style
MHS3 (3 fingers)/MHS(L)3
32 to 63
Parallel style MHS4 (4 fingers) 32 to 63
Angular style MHC2 10 to 25
180° Angular style MHW2 20 to 50
Air Cylinders
Description Series Bore size
Non-rotating double power cylinder
MGZ 40 to 63
Compact guide cylinder MGP 12 to 100
Auto Switch Mounting Bracket/Part No.
(Switch spacer and auto switch mounting bracket)
Cylinder series Bore size
40 50 63
MGZ BMP1-032 BMP1-032 BMP1-032
Note) When tightening an auto switch mounting screw, use a watchmaker’s
screwdriver with a grip diameter of 5 to 6 mm. Also, tighten with a torque of
about 0.037 to 0.074 lbf·ft (0.05 to 0.1 N·m)
As a guide, it should be turned about 90° past the point at which tightening
can be felt.
Note) When tightening an auto switch mounting screw, use a watchmaker’s
screwdriver with a grip diameter of 5 to 6 mm. Also, tighten with a torque of
about 0.037 to 0.074 lbf·ft (0.05 to 0.1 N·m)
As a guide, it should be turned about 90° past the point at which tightening
can be felt.

Trimmer Auto Switch D-M9K/D-7K/D-RK
6
How to Mount and Move the Auto Switch
D-F7K Mounting Bracket Rail Mounting Type
<Applicable auto switch>
Solid state ······ D-F7K
How to Mount and Move the Auto Switch
Auto Switch Mounting Bracket Part No. (Including Nut, Screw, (Spacer))
Cylinder
series
Bore size
12 16 20 25 32 40 50 63 80 100 125 140 160
CQ2 BQ-1 BQ-1 BQ-1 BQ-1 BQ-2 BQ-2 BQ-2 BQ-2 BQ-2 BQ-2 BQ-2 BQ-2 BQ-2
MU ———
BMU1-025 BMU1-025 BMU1-025 BMU1-025 BMU1-025 —————
MK/MK2
— — BQ-1 BQ-1 BQ-2 BQ-2 BQ-2 BQ-2 — — — — —
Auto switch
Auto switch mounting rail
Auto switch mounting nut∗
Auto switch mounting screw∗
(M3 x 0.5 x 8L)
Auto switch
Auto switch mounting nut
Auto switch mounting screw
(M3 x 0.5 x 6L)
∗When the CJ2 (rail mounting type) and the CM2-XC13
cylinders are ordered, nuts and screws are included.
Applicable Actuators
Air Cylinders
Description Series Bore size
Air cylinder CJ2 10, 16
Air cylinder CM2 20 to 40
Compact cylinder CQ2 12 to 160
Plate cylinder MU 25 to 63
Rotary clamp cylinder MK/MK2 20 to 63
1. Slide the auto switch mounting nut inserted into the mounting rail and
set it at the auto switch mounting position.
2. Fit the convex part of auto switch mounting arm into the concave part
of auto switch mounting rail. Then, slide the switch over the nut.
(Series CDQ2: Fit the convex part of auto switch mounting arm
through the auto switch spacer into the concave part of auto switch
mounting rail.)
3. Push the auto switch mounting screw lightly into the mounting nut
through the hole of auto switch mounting arm.
4. After reconfirming the detecting position, tighten the mounting screw
to secure the auto switch. (Tightening torque of M3 screw should be
0.37 to 0.52 lbf·ft (0.5 to 0.7 N·m.))
5. Modification of the detecting position should be made in the condition
of 3.

Series D-M9K/D-7K/D-RK
7
How to Mount and Move the Auto Switch
D-Y7K Mounting Bracket Tie-rod Mounting Type
<Applicable auto switch>
Solid state ······ D-Y7K
How to Mount and Move the Auto Switch
Auto Switch Mounting Bracket Part No.
(Including Bracket, Set Screw)
Cylinder
series
Bore size
40 50 63 80 100
CA2 BA4-040 BA4-040 BA4-063 BA4-080 BA4-080
Auto switch
mounting screw
Auto switch
Auto switch
mounting bracket
Hexagon socket head set screw Note 2)
Series CA2: M4 x 0.7 x 6L
Applicable Actuators
Air Cylinder
Description Series Bore size
Air cylinder CA2 40 to 100
Note 1) When tightening an auto switch mounting screw, use a
watchmaker’s screwdriver with a grip diameter of 5 to 6 mm.
Also, set the tightening torque to be 0.037 to 0.074 lbf·ft (0.05 to
0.1 N·m). As a guide, turn 90° from the position where it comes
to feel tight.
Note 2) Set the tightening torque of a hexagon socket head set screw
(M4 × 0.7) to be 0.74 to 0.89 lbf·ft (1 to 1.2 N·m).
1. Fix it to the detecting position with a set screw by installing an auto
switch mounting bracket in cylinder tie-rod and letting the bottom
surface of an auto switch mounting bracket contact the cylinder tube
firmly. Fix it to the detecting position with a set screw. (Use a hexagon
wrench.)
2. Fit an auto switch into the auto switch mounting groove to set it
roughly to the mounting position for an auto switch.
3. After confirming the detecting position, tighten up the mounting screw
attached to an auto switch, and secure the auto switch.
4. When changing the detecting position, carry out in the state of 2.
∗To protect auto switches, ensure that main body of an auto switch
should be embedded into auto switch mounting groove with a depth of
15 mm or more.

Design and Selection
Warning
Caution
Mounting and Adjustment
Caution
Wiring
Caution
Wiring
Caution
Operating Environment
Warning
Caution
Maintenance
Warning
Other
Caution
Trimmer Auto Switch
Specific Product Precautions
Be sure to read before handling. Refer to back cover for Safety Instructions. For Auto Switch Precautions, refer to “Handling
Precaution for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
1. Check the specifications.
Read the specifications carefully and use this product appropriately. The
product may be damaged or malfunction if it is used outside the range of
specifications of current load, voltage, temperature or impact.
2. Cautions for use in an interlock circuit
When an auto switch is used for an interlock signal requiring high
reliability, devise a double interlock system to avoid trouble by providing a
mechanical protection function, or by also using another switch (sensor)
together with the trimmer auto switch. Also, perform periodic
maintenance and confirm proper operation.
1. Take precautions when multiple cylinders are used close
together.
When 2 or more cylinders with trimmer auto switches are used in close
proximity, maintain a minimum actuator interval of 40 mm or more.
(When the allowable interval is indicated for each cylinder series, use the
specified values.) Magnetic field interference may cause the trimmer auto
switches to malfunction.
2. Keep the wiring as short as possible.
Use a wire 3 m or shorter between the sensor and amplifier. If the sensor
cable length exceeds 3 m, the CE marking does not apply to the auto
switch. Although wire length of power supply/output cable should not
affect switch function, use a wire 100 m or shorter.
3. Take precautions for the internal voltage drop of the switch.
Auto switches may not operate properly depending on the connected
equipment.
4. Take measures for rotational stoppage of the piston rod.
Take measures for rotational stoppage of the piston rod when designing
by guide etc. Or use non-rotating type SMC products. The operation may
be unstable.
1. Do not drop or bump.
Do not drop, bump or apply excessive impacts (980 m/s2 or more for
sensor unit and 98 m/s2 or more for amplifier unit) while handling.
Although the trimmer auto switch body may not be damaged, the inside
of the trimmer auto switch could be damaged and cause a malfunction.
2. Refer to the Operation Manual for how to adjust/set.
1. Avoid repeatedly bending or stretching lead wires.
Broken lead wires will result from applying bending stress or stretching
forces to the lead wires.
2. Be sure to connect the connector for sensor to the amplifier
before power is applied.
3. Do not allow short circuit of loads.
Output is automatically stopped when the protection circuit is working, as
the output unit registers any excess current flow, if loads are short
circuited. Should this occur, shut off the power supply, remove the cause
of this excess current flow and switch on the power again. Take special
care to avoid reverse wiring between the power supply line (brown) and
the output line (black, white).
4. Avoid incorrect wiring.
If the connections are reversed (power supply line + and power supply
line –), the trimmer auto switches will be protected by a protection circuit.
However, if the power supply line (–) is connected to the black, white
wire, the trimmer auto switches will be damaged.
1. Never use in an atmosphere with explosive gases.
The structure of trimmer auto switches is not designed to prevent
explosion. Never use in an atmosphere with an explosive gas since this
may cause a serious explosion.
1. Do not use in an area where a magnetic field is generated.
Trimmer auto switches will malfunction or magnets inside actuators will
become demagnetized.
2. Do not use in an environment where the trimmer auto
switch will be continually exposed to water.
Although the sensor units of trimmer auto switches satisfy the IEC
standard IP67 structure, do not use trimmer auto switches in applications
where continually exposed to water splash or spray. Poor insulation or
swelling of the potting resin inside trimmer auto switches may cause a
malfunction. (Amplifier unit D-RNK and RPK: IP40)
3. Do not use in an environment with oil or chemicals.
Please consult with SMC if trimmer auto switches will be used in an
environment with coolant, cleaning solvent, various oils or chemicals. If
trimmer auto switches are used under these conditions for even a short
time, they may be adversely affected by improper insulation, malfunction
due to swelling of the potting resin, or hardening of the lead wires.
4. Take measures against freezing when operating at 41 ° F
(5°C ) or less.
1. Perform the following maintenance periodically in order to
prevent possible danger due to unexpected trimmer auto
switch malfunction.
1) Secure and tighten trimmer auto switch mounting screws.
If screws become loose or the mounting position is dislocated,
retighten them after readjusting the mounting position.
2) Confirm that there is no damage to lead wires.
To prevent faulty insulation, replace trimmer auto switches or repair
lead wires, etc., if damage is discovered.
1. Please consult with SMC concerning water resistance, elasticity of
lead wires, and usage at welding sites, etc.
8

∗ Added applicable actuators.
∗ The descriptions in the pictures on the cover page were corrected.
∗ Large workpiece: OUT1 Green light is ON. →OUT2 Orange light is ON.
∗ Small workpiece: OUT2 Orange light is ON. →OUT1 Green light is ON. JY
∗ The sensor unit (D-M9K) applicable to the direct mounting (round groove)
type newly added. SO
Revision history
Edition B
Edition C
1. The compatibility of the product is the responsibility of the
person who designs the equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its
compatibility with specific equipment must be decided by the person who designs
the equipment or decides its specifications based on necessary analysis and test
results. The expected performance and safety assurance of the equipment will be
the responsibility of the person who has determined its compatibility with the
product. This person should also continuously review all specifications of the
product referring to its latest catalog information, with a view to giving due
consideration to any possibility of equipment failure when configuring the
equipment.
2. Only personnel with appropriate training should operate
machinery and equipment.
The product specified here may become unsafe if handled incorrectly. The
assembly, operation and maintenance of machines or equipment including our
products must be performed by an operator who is appropriately trained and
experienced.
3. Do not service or attempt to remove product and machinery/
equipment until safety is confirmed.
1. The inspection and maintenance of machinery/equipment should only be
performed after measures to prevent falling or runaway of the driven objects
have been confirmed.
2. When the product is to be removed, confirm that the safety measures as
mentioned above are implemented and the power from any appropriate source
is cut, and read and understand the specific product precautions of all relevant
products carefully.
3. Before machinery/equipment is restarted, take measures to prevent
unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety
measures if the product is to be used in any of the following
conditions.
1. Conditions and environments outside of the given specifications, or use
outdoors or in a place exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air
navigation, space, shipping, vehicles, military, medical treatment, combustion
and recreation, or equipment in contact with food and beverages, emergency
stop circuits, clutch and brake circuits in press applications, safety equipment
or other applications unsuitable for the standard specifications described in the
product catalog.
3. An application which could have negative effects on people, property, or
animals requiring special safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for
possible failure by using a mechanical protective function, and periodical
checks to confirm proper operation.
Warning
Limited warranty and Disclaimer/
Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer”
and “Compliance Requirements”.
Read and accept them before using the product.
1. The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in
manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and
exchange specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Caution
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after
the product is delivered, whichever is first.∗2)
Also, the product may have specified durability, running distance or
replacement parts. Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our
responsibility, a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any
other damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms
and disclaimers noted in the specified catalog for the particular products.
∗2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad
or failure due to the deterioration of rubber material are not covered by the limited warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of
weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are
governed by the relevant security laws and regulations of the countries involved
in the transaction. Prior to the shipment of a SMC product to another country,
assure that all local rules governing that export are known and followed.
These safety instructions are intended to prevent hazardous situations and/or
equipment damage. These instructions indicate the level of potential hazard with
the labels of “Caution,” “Warning” or “Danger.”They are all important notes for
safety and must be followed in addition to International Standards (ISO/IEC)∗1),
and other safety regulations.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
ISO 4413: Hydraulic fluid power – General rules relating to systems.
IEC 60204-1: Safety of machinery – Electrical equipment of machines.
(Part 1: General requirements)
ISO 10218-1: Manipulating industrial robots – Safety.
etc.
Caution indicates a hazard with a low level of risk
which, if not avoided, could result in minor or
moderate injury.
Warning indicates a hazard with a medium level of
risk which, if not avoided, could result in death or
serious injury.
Caution:
Warning :
Danger :Danger indicates a hazard with a high level of risk
which, if not avoided, will result in death or serious
injury.
Safety Instructions
Safety Instructions Be sure to read “Handling Precautionsfor SMC Products” (M-E03-3) before using.
9

Global Manufacturing, Distribution and Service Network
Worldwide Subsidiaries
U.S. & Canadian Sales Offices
Atlanta
Birmingham
Boston
Charlotte
Nashville
New Jersey
Rochester
Tampa
Montreal
Austin
Dallas
Los Angeles
Phoenix
Portland
San Francisco
Vancouver
Chicago
Cincinnati
Cleveland
Detroit
Indianapolis
Milwaukee
Minneapolis
St. Louis
Toronto
Windsor
EAST
Vancouver
Toronto
Windsor
Montreal
CANADA
CENTRAL
WEST
© 2014 SMC Corporation of America, All Rights Reserved.
All reasonable efforts to ensure the accuracy of the information detailed in this catalog were made at the time of publishing.
However, SMC can in no way warrant the information herein contained as specifications are subject to change without notice.
Vancouver
Chicago
Indianapolis
Atlanta
Austin
Livermore
Detroit
Boston
Montreal
Toronto
Sales Branches
Regional
Distribution Centers
Central warehouse
SQ-RRD-5M
EUROPE
AUSTRIA
SMC Pneumatik GmbH (Austria)
BELGIUM
SMC Pneumatics N.V./S.A.
BULGARIA
SMC Industrial Automation Bulgaria EOOD
CROATIA
SMC Industrijska Automatika d.o.o.
CZECH
SMC Industrial Automation CZ s.r.o.
DENMARK
SMC Pneumatik A/S
ESTONIA
SMC Pneumatics Estonia
FINLAND
SMC Pneumatics Finland OY
FRANCE
SMC Pneumatique S.A.
GERMANY
SMC Pneumatik GmbH
GREECE
SMC Hellas EPE
HUNGARY
SMC Hungary Ipari Automatizálási Kft.
IRELAND
SMC Pneumatics (Ireland) Ltd.
ITALY
SMC Italia S.p.A.
LATVIA
SMC Pneumatics Latvia SIA
LITHUANIA
SMC Pneumatics Lietuva, UAB
NETHERLANDS
SMC Pneumatics BV
NORWAY
SMC Pneumatics Norway A/S
POLAND
SMC Industrial Automation Polska Sp.z.o.o.
ROMANIA
SMC Romania S.r.l.
RUSSIA
SMC Pneumatik LLC.
SLOVAKIA
SMC Priemyselná Automatizáciá, s.r.o.
SLOVENIA
SMC Industrijska Avtomatika d.o.o.
SPAIN / PORTUGAL
SMC España, S.A.
SWEDEN
SMC Pneumatics Sweden AB
SWITZERLAND
SMC Pneumatik AG
UK
SMC Pneumatics (U.K.) Ltd.
ASIA
CHINA
SMC (China) Co., Ltd.
HONG KONG
SMC Pneumatics (Hong kong) Ltd.
INDIA
SMC Pneumatics (India) Pvt. Ltd.
JAPAN
SMC Corporation
MALAYSIA
SMC Pneumatics (S.E.A.) Sdn. Bhd.
PHILIPPINES
SMC Pneumatics (Philippines), Inc.
SINGAPORE
SMC Pneumatics (S.E.A.) Pte. Ltd.
SOUTH KOREA
SMC Pneumatics Korea Co., Ltd.
TAIWAN
SMC Pneumatics (Taiwan) Co., Ltd.
THAILAND
SMC Thailand Ltd.
NORTH AMERICA
CANADA
SMC Pneumatics (Canada) Ltd.
MEXICO
SMC Corporation (Mexico) S.A. DE C.V.
USA
SMC Corporation of America
SOUTH AMERICA
ARGENTINA
SMC Argentina S.A.
BOLIVIA
SMC Pneumatics Bolivia S.R.L.
BRAZIL
SMC Pneumaticos do Brazil Ltda.
CHILE
SMC Pneumatics (Chile) S.A.
VENEZUELA
SMC Neumatica Venezuela S.A.
OCEANIA
AUSTRALIA
SMC Pneumatics (Australia) Pty. Ltd.
NEW ZEALAND
SMC Pneumatics (N.Z.) Ltd.