Solowave Ridgeview Clubhouse User manual

INSTALLATION AND OPERATING INSTRUCTIONS
RIDGEVIEW CLUBHOUSE PLAY SYSTEM – F270850TARX
8 - 10 Hrs
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions
often and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 27’6" x 28’ (8.4 x 8.5 m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 7’6” (2.3 m)
CAPACITY - 9 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries,
day cares or parks
Rev 01/23/2012
3400850ITAR
Two person
assembly
Table of Contents
Warnings and Safe Play Instructions . . . . . . . . . . pg. 2
Protective Surfacing Guidelines . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . pg. 6
Part ID ..................................pg. 7
Installation of I.D./Warning Plaque . . . . . . . . Final Step
WARNING
Solowave Design
375 Sligo Rd. West, PO Box 10
Mount Forest, ON Canada N0G 2L1
General Inquiries:
8:00am - 4:30pm EST
Toll Free: 1 800 357 465
[email protected]
8.4m
8.5m
4.1m
4.4m
General Inquiries: Solowave Design
375 Sigo Rd. West • PO Box 10 • N0G 2L1
Mount Forest, Ontario • Canada
Please call toll free: 1 800-357-465
For questions, assembly help or assistance with missing or defective parts.
______________________________________________________
______________________________________________________
Rev 02/29/2012
3400850ITARX

 2 [email protected]
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Observe capacity limitations of your play-set. See
front cover.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center
of the swing seat to prevent erratic swing motion or
falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or
run up slide.
WARNING
WARNING – Safe Play Instructions
2
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD
Prior to assembly, this product contains small parts.
DO NOT allow children less than 5 years of age near or
around loose nuts, screws, washers, plastic bags and
other small parts.
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose fitting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.

 3 [email protected]

 4 [email protected]

 5 [email protected]
About Our Wood
Solowave Design™ uses only premium playset lumber, ensuring the safest product for your children’s use. Although great care has
been taken in selecting the best quality lumber available, wood is a product of nature and susceptible to weathering (changes in the
aesthetics of the wood). A light sanding may be required to remove minor splinters. For your information, we have described some
changes that may occur as a result of weathering:
1. Checking Checks are surface cracks in the wood along the grain. 4” x 4” material will experience more checking than 2”, 1-1/4” or 1”
material be cause the surface and interior moisture content will vary more widely than in thinner wood.
2. Warping Warping refers to any distortion (twisting, cupping) from the true plane that may take place during weathering.
3. Fading Wood exposed to sunlight, will over time, turn a grey color.
Note: The above changes will not affect the strength of the product.
What causes weathering?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is different
than the interior of the wood. As the moisture moves in or out of the wood (result of climate changes), the different moisture content
causes tension in the wood, which can result in checking and or warping.
How can I reduce the amount of weathering to my Play System?
At the factory we have added water repellent to the stain. This water repellent decreases the amount of water absorption during rain or
snow thus decreasing the tension in the wood. Sunlight will break down the water repellent, so we recommend applying a water repellent
on a yearly basis (see your local stain and paint supplier for a recommended product). Also if storing the product before installation, make
sure you store out of direct sunlight in a cool dry place.
Will weathering affect the strength of my Play System?
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are concerned
that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.
Complete and mail registration card to receive important product notications and assure prompt
warranty service.
2 Year Limited Warranty
Solowave Design warrants that this product is free from defect in materials and workmanship for a
period of one year from the original date of purchase. In addition, lumber is warranted for 2 years
against structural failure due to rot and insect damage. All other parts, such as hardware, swings, rides,
accessories, and slides carry a one-year warranty only.
This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your Play System. This warranty does not
cover any inspection cost.
This Limited Warranty does not cover:
• Labor for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature;
• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not
affect performance or integrity.
Solowave Design products have been designed for safety and quality. Any modications made to
the original product could damage the structural integrity of the unit leading to failure and possible
injury. Solowave Design Inc. cannot assume any responsibility for modied products. Furthermore,
modication voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Solowave
Design Play System be used in public settings such as schools, churches, playgrounds, parks, day
cares and the like. Such use may lead to product failure and potential injury. Any and all public use
will void this warranty.
Solowave Design disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or
province to province. This warranty excludes all consequential damages, however, some states do not allow the
limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
5
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

 6 [email protected]
Keys to Assembly Success
Part Identification Key
On each page, you will find the parts and
quantities required to complete the assembly
step illustrated on that page. Here is a sample.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove the
bolt and add washers to eliminate this condition. Extra
washers have been provided for this purpose.
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole before
fastening screw or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill
1/8” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Tools Required
6
Shovel Level #2 & #3 Phillips
or Robertson
Safety
Glasses
Drill (1/8”
3/16” Bit)
Measuring
Tape
Hammer Ratchet 1/2”,
7/16” & 9/16”
Square
Ruler
Step
Ladder
12342X Post 2 x 4 x 83”

 7 [email protected]
1 inch = 25.4mm
SOLO)WAVE DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38 1¼ 32
1-1/8 29
1 25.4
7/8 22 3/4 19 1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm) Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm) T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm) Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm) Flat Washer
5/16" (8mm) Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm) T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm) Flat Washer

 8 [email protected]
5/4 x 5
4 1/2"
114.3
1"
25.4
5/4 x 4
3 1/2"
88.9
1"
25.4
1 inch = 25.4mm
For example:
1505mm
=
LENGTH CONVERSION
SOLO)WAVE DESIGN WOOD PROFILES
BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm
IMPORTANT: Dimensions in brackets [mm] represent millimetres.
1 x 2
1 x 4
1 x 5
1 x 6
15.9
5/8" 3 3/8"
85.7
2 x 4
3 3/8"
85.7
1 3/8"
34.9
2 x 2
1 1/2"
38.1
1 1/2"
38.1
2 x 3
2 1/2"
63.5
1 3/8"
34.9
4 1/2"
114.3
5/8"
15.9
5 3/8"
136.5
5/8"
15.9
5/4 x 6
5 1/2"
139.7
1"
25.4
4 x 6
5 1/4"
133.4
3 1/4"
82.6
4 x 4
3 1/4"
82.6
3 1/4"
82.6
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1

 9 [email protected]
Part Identification (Reduced Size)
(4) Post (2 x 4 x 83")
3660213
011
Box 2
3660360
Box 2
060
(1) Back Divider (1 x 4 x 35 1/4")
3660506
(1) Ground 1 x 5 x 78"
012
Box 1
(1) Floor (1 x 6 x 39 1/4")
3660388
Box 2
(1) SW Roof Side (1 x 4 x 59 1/2")
3660366
Box 2
3660387
(1) Floor End (1 x 6 x 38 1/4")
021
Box 2
Box 2(1) Roof Side (1 x 4 x 59 1/2")
3660513
022
3660508
(1) Side Ground (1 x 5 x 38 1/4') Box 1
020
(1) Floor Front (2 x 3 x 46 1/4")
3660529
031
Box 2
(2) Front Back Ground (1 x 5 x 46 5/8")
3660505
Box 2
030
(1) Floor Back (5/4 x 4 x 46 3/4")
3660799
040
Box 1
(1) Door Top (1 x 4 x 47 1/4")
3660519
051
Box 2
Box 2
3660500
050
(1) Centre Divider 2 x 4 x 35 3/8"
Box 2(1) Top Back (1 x 4 x 46 1/2")
3660530
(1) Side Joist (2 x 2 x 43 5/8")
3660509
Box 2
(1) Back Arch (1 x 6 x 46 1/2") Box 2
062 3660511
(1) Floor Joist (5/4 x 4 x 46½") Box 1
0713660790
Box 1(2) Cedar Gap Board (1 x 5 x 35 1/4")
070 3610710
Box 2
3610621
(7) Cedar Floor Board (1 x 5 x 35 1/4")
080
(1) Gap (2 x 4 x 17")
093
Box 2
(1) Floor Gap (2 x 4 x 25 1/4")
3660525
092
Box 2
Box 2(2) Floor Gusset (2 x 3 x 11)
091 3660367
3660504
(1) SW Mount (2 x 4 x 40 3/4")
090
Box 1
(1) Cedar Wall (1 x 4 x 28")
3625265
101
Box 2
(2) Side Chalk Wall (1 x 4 x 25 1/4")
3620528
100
Box 1
1" x 6"
5/4" x 4"
2" x 4"
2" x 2"
013
052
3660526
061
2" x 3"
Nominal Size
2" x 6"
010
Actual Size
1½" x 5⅜"
1⅜" x 3⅜"
1⅜" x 2½"
1½" x 1½"
1" x 3½"
⅝" x 5⅜"

 10 [email protected]
152
110
Box 2
Box 2
120
Part Identification (Reduced Size)
3620304
(5) CE Floor Board (1 x 4 x 32 1/2")
3620524
Box 1
170
(17) Siding (3/8 x 3 1/2 x 26 3/4)
Box 1
3660372
(7) Wall Brace (5/4 x 2 x 45 3/4")
160
3660516
(2) Bottom Arch (1 x 6 x 24") Box 2
3660515
(2) Top (1 x 6 x 13 1/2")
151
Box 1
(4) Roof Brace (1 x 6 x 13") Box 1
3660514
150
3660501
(2) Joist (2 x 2 x 43 1/2")
142 Box 1
Box 1
3620863
141
(4) CE Roof Support (2 x 3 x 43 1/2")
(4) CE Wall Boards (1 x 6 x 23 1/2"
3620702
111
Box 2
(2) Tarp Front Back (1 x 4 x 47¾")
3660357
130
Box 2
3660502
(1) Side Top (1 x 6 x 38 1/4") Box 1
3620517
Box 1
140
(26) Cedar Roofing (3/8 x 3½ x 48")
Box 2
3660349
223
(2) Rock Rail (2 x 3 x 51")
(2) Side Wall (1 x 5 x 38 1/4")
3660512
112
Box 2
(2) CE Rock Board (1 x 6 x 19-3/4")
3610630
221 Box 2
3610606
220
(2) CE Access Board (1 x 6 x 19¾")
(3) CE Rock Board (1 x 6 x 19-3/4")
3610631
222
Box 2
Box 1(2) Trim 3/8 x 2 1/4 x 20 1/4"
3660507
213
3660389
(2) Window Frame (1 x 2 x 16 1/4")
182
3620523 Box 2
181
(5) CE Siding (3/8 x 3 1/2 x 7 3/4") 3660503
(3) Trim (3/8 x 2 1/4 x 40")
212
Box 1
(2) Trim Short (3/8 x 2 x 20 1/4")
3620386
211
Box 1
(1) Table Top (5/4 x 6 x 32")
3660376
190
Box 1
3660374 Box 2
(2) Short Wall Brace (5/4 x 2 x 25 1/2")
191
3660510
(1) Table Support 2 x 2 x 40 1/2"
192
Box 2
3620518
Box 2
180
(7) Cedar Siding (3/8 x 3 1/2 x 46 5/8")
(4) Lower Diagonal (2 x 3 x 37")
3660369
Box 2
230
(3) Trim Corner (3/8 x 2 x 40")
3620370
210
Box 1
3620379
Box 2
161
(18) CE SIDING (3/8 x 3½ x 38¾")

 11 [email protected]
Part Identification (Reduced Size)
(3) Tenon Dowel (1 1/8 x 15 7/8")
(1) Chalk Wall Tarp(3750702)
ABC
Box 1
253
254
251
(1) SW Rail Block (2 x 4 x 5 3/8")
3664919
3681578
(6) Ground Stake (1-1/4 x 1-1/2 x 14")
3681858
270 3650318
240
242
244
(1) SW Upright (2 x 4 x 50 1/2')
243
Box 1
Box 1
245 Box 2
250
252
(2) Tenon Dowel (1 1/8 x 18 5/8")
241
(1) Slide 48"
High Rail (3310148)
(1) Rocks w/ hardware
(3320385) (pk5)
Box 1
(2) SW Post (2 x 4 x 92 1/2") Box 1
3666922
(9200840)
(1) Cafe Canopy Frame
(1) Cafe Canopy
(9750810)
Ridgeview Tarp Set
3750850
(1) Triangle Plate
(3200184) (4pk)
(1) Stool Seat Set
(3320190)
(1) CE Floor Board (1 x 6 x 35 1/4") Box 2
081 3610602
Box 2
(1) MK Ground (1 x 4 x 55-1/4")
3660353
(2) MK Post (2 x 3 x 79 1/2") Box 2
3660352
(2) MK Rail (2 x 4 x55")
Box 2
3660344
3644920
Box 1
3644921
(1) SW Support (5/4 x 4 x 48 1/2")
(3320094)
(1) Door Window
with hardware
(2) Long Belt Swing (3724931)
(1) Glider Hanger
(3200202)(2pk)
(1) Front Beam (2 x 6 x 94") 3661248 Box 1
(1) Glider Rope/Chain (4pk) (3533859)
(1) Space Glider Body
Yellow (3320268)
(2) Space Glider Handle
Green (3320177)
(1) Back Beam (2 x 6 x 94") 3661249 Box 1

 12 [email protected]
(1) Monkey Bracket
3200300 (4pk)
Not actual size
H7
(5) Hex Bolt 1/4 x 5 1/2" 9277252
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
H5
(2) Hex Bolt 1/4 x 4 1/2" 9277242
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
GL8
(2) Hex Bolt 5/16 x 2" 9277320
5/16" Flat Washer - 5/16" Flat Washer - 5/16" Lock-Nut
H1
(1) Hex Bolt 1/4 x 1 1/2" 9277212
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
H3
H6
(2) Hex Bolt 1/4 x 4 3/4 9277243
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
(4) Hex Bolt 5/16 x 4" 9277340
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut
PB2
Lock Washer 1/4" Flat Washer 1/4" T-Nut
(1) Pan Bolt 1/4 x 1 1/4"
9274211
G2
(4) Hex Bolt 5/16 x 1" 9277310
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut
H4
(1) Hex Bolt 1/4 x 4" 9277240
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
H8
(1) Hex Bolt 1/4 x 4 1/4" 9277241
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
(4) Hex Bolt 5/16 x 1 1/2" 9277312
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut
H2
H12
(2) Hex Bolt 1/4 x 3" 9277230
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
G4
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
9277220
(20) Hex Bolt 1/4 x 2"
G1
(2) Hex Bolt 1/4 x 2 1/2" 9277222
1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut
Hardware Identification (Actual Size)
10

 13 [email protected]
S1
(52) Flat Head Screw #8 x 1 1/8" (9290514)
(37)
1/4" T-Nut
(9285200)
(54)
1/4" Flat Washer
(9251200)
(2 pk of 2)
Corner Brace
w/screws
(9201100)
9262230
LS3
S2
(160) Flat Head Screw #8 x 1 1/2' (9260512)
(20)
5/16" Lock Washer
(9253300)
(2) Lag Screw 1/4 x 2 1/2" -1/4" Flat Washer
9262222
-1/4" Flat Washer
(11) Lag Screw 1/4 x 3"
LS2
1/4" Flat Washer
(4) Lag Screw 1/4 x 1 1/2"
9262212
LS1
S6
(18) Pan Screw #12 x 1" (9264610)
(37)
1/4" Lock Washer
(9253200)
(21) #8 Flat Washer
(9251500)
(246) Truss Screw #8 x 7/8" (9229505)
S0
(36)
5/16" Flat Washer
(9251300)
S5
(21) Pan Screw #8 x 1/2" (9264504)
S4
(15) Flat Head Screw #8 x 3" (9290530)
S3
(22) Flat Head Screw #8 x 2 1/2" (9260522)
(16)
3/16" Flat Washer
(9251100)
(8)
5/16" Ny-lok Nut
(9283300)
S7
(28) Pan Screw #12 x 2" (9294620)
TS (43) Trim Screw #6 x 30mm (9224911)
(3) Hex Bolt 5/16 x 3"
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut
G10 9277330
Hardware Identification (Actual Size)
5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut (5) Hex Bolt 5/16 x 4-1/2"
G5 9277342
(20)
5/16" T-Nut
(9285300)
(1 pk of 4)
Bolt Thru Hangers
(3202000)
9277471
G25
(2) Hex Bolt 5/16 x 7¼" Zinc -(2) 5/16" Flat Washer & Nylok Nut
(2) 5/16" Flat Washer & Nylok Nut (4) Hex Bolt 5/16 x 5½" Zinc -
9277352
G7

 14 [email protected]
X26
Long Belt Swing
242
Body
140
010
230
051
071
070
040
X2
050
060
062
X4
141
X2
142
X7
180
100
X2
X18
161
192
X2
X2
220
220
221
221
190
222
213
222
211
222
223 X2
031
X3
251
X2
253
254
270
243
244
X6
240
241
X5
052 120
X7
160
X4
Hight Rail Slide
Rocks
Handle
Stool Seat Set
X2
Space Glider
Space Glider
250
252
RIDGEVIEWCLUBHOUSEPLAYSYSTEM–F270850ITARX
PARTSIDENTIFICATION‐FRONT
181
160
180 182
011
170 X17
X7
X5
Inside view
Door Window
180

 15 [email protected]
061
081
160
High Rail Slide
RIDGEVIEWCLUBHOUSEPLAYSYSTEM–F270850ITARX PARTSIDENTIFICATION‐REAR
X2
013
245
101 092
093
051
080
X7
081
050
062
142
170
X2
X17
030
X2
191
192
090
241
022
X4
111
110
X2
112
021
011
X4
020
151 X2
152 X2
150 X4
210
X3
212
X3
Glider Hanger
091
Stool Seat Set
Ridgeview Tarp Set
012
Triangle Plate
130
X2

 16 [email protected]
1-877-966-3738
[email protected]
B.Ifthereareanymissingordamagedpiecesoryouneedassistancewith
assemblypleasecontacttheConsumerRelationsDepartmentdirectly.Callus
beforegoingbacktothestore.
STOP STOPSTOP STOP
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Readtheassemblymanualcompletely,payingspecialattentiontoANSIwarnings;
notes;andsafety/maintenanceinformationonpages1-6.
D. Beforeyoudiscardyourcartonsllouttheformbelow.

•ThecartonI.D.stampislocatedontheendofeachcarton.Thetrackingnumberis
locatedontheBigBackyardIDPlaque(3320356).
 •Pleaseretainthisinformationforfuturereference.Youwillneedthisinformationifyou
contacttheConsumerRelationsDepartment.
•PleaserefertoPage6forproperhardwareassembly.

•Eachstepindicateswhichboltsand/orscrewsyouwillneedforassembly,aswellas
anyatwashers,lockwashers,t-nutsorlocknuts.
A.Thisisthetimeforyoutoinventoryallyourhardware,woodandaccessories,
referencingthepartsidenticationsheets.Thiswillassistyouwithyourassembly.

•Thewoodpieceswillhavethefourdigitkeynumberstampedontheendsofthe
boards.Thewoodpiecesarereferencedthroughouttheinstructionswiththisnumber.
CARTONI.D.STAMP:__________14459___(Box4)
CARTONI.D.STAMP:__________14459___(Box5)
CARTONI.D.STAMP:__________14459___(Box6)
CARTONI.D.STAMP:__________14459___(Box1)
CARTONI.D.STAMP:__________14459___(Box2)
CARTONI.D.STAMP:__________14459___(Box3)
MODELNUMBER:F270850TARX
TRACKINGNUMBER(fromIDPlaque):

 17 [email protected]
Assembly
Square
Bolts
Then
Then
TightenSquare
Assembly
over extends post.
Note: This end
H2
010
H2
013 012
H2
011
This is the
shorter side
20" Approx.
to centre
013
LS1
011
BOLTING EXAMPLE
(1/4" Flat Washer)
Step 1 Swing Wall Assembly
B23
B18
Wood Parts Hardware Other Parts
B12
2X
1X 1 x 6 x 39-1/4" Floor
1/4 x 1½" Lag Screw
1X 1 x 5 x 78" Ground
1/4 x 2" Hex Bolt
(1/4" Lock Washer, Flat Washer, T-Nut)
2X 2 x 4 x 83" Post
A15
1X 1 x 4 x 59-1/2" SW Roof Side
LS1
H2
8X
Use factory drilled
hole as a guide
Predrill 1/8"
pilot hole
Predrill Pilot Holes for Lag Screws
A: Attach (012) SW Roof Side, (013) Floor and (010) Ground to 2 (011) Posts using (H2) 1/4 x 2” hex bolts
(with at washer, lock washer and t-nut) as shown below. Notice the hole locations of both (013) Floor
and (010) Ground.
B: Make sure Assembly is square and then in the top holes of the (013) Floor fasten to the (011) Posts
using 2 (LS1) 1/ x 1-1/2” lag screws (with at washer).
13
1 x 1 x 5 x 78” Ground
2 x 2 x 4 x 83” Post
1 x 1 x 4 x 59-1/2” SW Roof Side
1 x 1 x 6 x 39-1/4” Floor
013
012
011
010

 18 [email protected]
Tighten
Bolts
8X
Square, Add Lag Screws
(1/4" Flat Washer)
2X 2 x 4 x 83" Post
A17
5/16" T-Nut
B22
B31
B12
Step 2 Wall Assembly
1X 1 x 4 x 59-1/2" Roof Side
Wood Parts Hardware Other Parts
2X
1X 1 x 6 x 38-1/4" Floor End
1/4 x 1½" Lag Screw
1X 1 x 5 x 38-1/4" Side Ground
1/4 x 2" Hex Bolt
(1/4" Lock Washer, Flat Washer, T-Nut)
LS1
H2
4X
Square
Assembly
Square
Bolts
Assembly Then
Tighten
Then
H2
BOLTING EXAMPLE
locations H2
021 022
H2
020
011
Notice hole
Use factory drilled
hole as a guide
Predrill 1/8"
pilot hole
Predrill Pilot Holes for Lag Screws
021
LS1
020
Notice T-Nuts
were separately
installed
A: Attach (022) Roof Side, (021) Floor End and (020) Side Ground to 2 (011) Posts using (H2) 1/4 x 2” hex
bolts (with at washer, lock washer and t-nut) as shown below. Notice the hole locations of both (013)
Floor and (020) Side Ground.
B: Make sure Assembly is square and then in the top holes of the (021) Floor End fasten to the (011)
Posts using 2 (LS1) 1/4 x 1-1/2” lag screws (with at washer).
C: Add 4 5/16 t-nuts to (020) Side Ground from underneath. These t-nuts will be used in a later step.
14
1 x 1 x 5 x 38-1/4” Side Ground
2 x 2 x 4 x 83” Post
1 x 1 x 6 x 38-1/4” Floor End
1 x 1 x 4 x 59-1/2” Roof Side
022
021
011
020

 19 [email protected]
Use
Help Assembly
Square
Then
2X
#12 x 2" Pan Screw (3/16" Flat Washer)
1/4 x 3" Lag Screw
B26
Step 3 Front Frame Assembly
(1/4" Flat Washer)
B37
Wood Parts Hardware Other Parts
1X 1 x 5 x 46-5/8" Front Back Ground
1X 2 x 3 x 46-1/4" Floor Front
2X
(1/4" Lock Washer, Flat Washer, T-Nut)
1/4 x 4¾" Hex Bolt
LS3
H6
S7
2X
BOLTING EXAMPLE
Use factory drilled
hole as a guide
Predrill 1/8"
pilot hole
Predrill Pilot Holes for Lag Screws
Swing Wall Assembly
S7
H6
031
Wall Assembly
011
LS3
030
A: Attach (031) Floor Front to inside of both Wall Assemblies using 2 (H6) 1/4 x 4-3/4” hex bolts (with at
washer, lock washer and t-nut). Bolts are installed from the inside of the fort.
B: Make sure Assembly is square and then pre-drill pilot holes using a 1/8” drill bit before attaching lag
screws. Attach (030) Front Back Ground to the outside of both Wall Assemblies using 2 (LS3) 1/4 x 3”
lag screws (with at washer) in the bottom holes and 2 (S7) #12 x 2” pan screws (with at washer)
in the top holes.
15
1 x 1 x 5 x 46-5/8” Front Back Ground
1 x 2 x 3 x 46-1/4” Floor Front
031
030

 20 [email protected]
Use
Help
2X
#12 x 2" Pan Screw (3/16" Flat Washer)
Step 4 Back Frame Assembly
A21
Wood Parts Hardware Other Parts
B26 (1/4" Flat Washer)
2X
1X 5/4 x 4 x 46-3/4" Floor Back 1/4 x 3" Lag Screw
1/4 x 4½" Hex Bolt
(1/4" Lock Washer, Flat Washer, T-Nut)
LS3
1X 1 x 5 x 46-5/8" Front Back Ground H5
S7
2X
Assembly
Square
Then
Notice hole
030
040
Wall Assembly
H5
Swing Wall Assembly
LS3
S7
011
orientation
011
BOLTING EXAMPLE
hole as a guide
Use factory drilled
Predrill 1/8"
pilot hole
Predrill Pilot Holes for Lag Screws
A: Attach (040) Floor Back to outside of both Wall Assemblies using 2 (H5) 1/4 x 4-1/2” hex bolts (with at
washer, lock washer and t-nut). Bolts are installed from the inside of the fort.
B: Make sure Assembly is square and then pre-drill pilot holes using a 1/8” drill bit before attaching lag
screws. Attach (030) Front Back Ground to the outside of both Wall Assemblies using 2 (LS3) 1/4 x 3”
lag screws (with at washer) in the bottom holes and 2 (S7) #12 x 2” pan screws (with at washer)
in the top holes.
16
1 x 5/4 x 4 x 46-3/4” Floor Back
1 x 1 x 5 x 46-5/8” Front Back Ground
030
040