Spartan 1149 User manual

01/12
Children Seesaw
WARNING:
1. THIS SEE-SAW MUST BE ASSEMBLED BY AN ADULT AND MAKE SURE ALL THE
NUTS AND BOLTS ARE SCREWED TIGHTLY BEFORE USE.
2. THIS SEE-SAW CAN BE USED INDOOR OR OUTDOOR.
3. THIS SEE-SAW CAN BE USED ON SOFT GROUND.EG GRASS.
4. THIS UNIT MUST BE USED UNDER THE SUPERVISION OF ADULT.
5. AGE RECOMMENDATION: 3-5 YEARS. MAXIMUM WEIGHT FOR EACH SEAT - 110LB.
6. THIS SEE-SAW IS NOT SUITABLE FOR CHILDREN UNDER THE AGE OF 3 YEARS OLD DUE TO
SMALL PART-CHOKING HAZARD.
7. FOR FAMILY DOMESTIC USE ONLY.
8. PLEASE KEEP THE ASSEMBLY INSTRUCTION AND ALL INFORMATION FOR FUTURE
REFERENCE.

MAIN BAR 1PC HANDLES 2PCS UPPER SUPPORTER 1PC LOWER SUPPORT TUBE 1PC
LEGS(A) 2PCS LEGS(B) 2PCS STOP BARS 2PCS COPULAR TUBE 4PCS SEATS 2PCS
M8x50 BOLT 1PC M8 NUT 1PC M8 WASHER 1PC M6X85BOLT 4PCS M6X90BOLT 4PCS
SQUARE HEAD M6X55BOLT 8PCS M6X40BOLT 2PCS M6 NUT 18PCS M6 WASHER 22PCS
STEP 1：CONNECT HANDLES TO MAIN BAR USING M6X40 BOLT AND M6 NYLON WASHERS M6 NUT FOR BOTH SIDES
STEP 2：ALIGNING THE HOLES OF THE SEAT TUBES WITH THE HOLES OF THE MAIN BAR AND INSERT BOLT (M6X90)
INTO THEM, ATTACH WASHERS AND SCREW NUTS TIGHTLY AT EACH END OF THE BOLTS. ATTENTION: HERE YOU
NEED 8 M6 NYLON WASHERS. (SEE THE FIGURE UNDERNEATH)
PACKAGE COMPONENTS
—1—
ASSEMBLE INSTRUCTION

STEP 3：PUT THE SEATS ONTO THE ASSEMBLED SEAT TUBES AND INSERT SQUARE HEAD M6X55 BOLTS THROUGH
THEM,SCREW THE BOLTS SUFFICIENTLY AFTER ATTACHING THE STOP BAR AND WASHERS. ASSEMBLE THE OTHER
SIDE BY THE SAME WAY.
STEP 4: PUT THE MAIN BAR AND M8 WASHER BETWEEN THE CLIP OF THE UPPER SUPPORTER AND ALIGNING THEIR
HOLES, INSERT THE (M8X50) BOLT THROUGH THEM AND ATTACH A WASHER, SCREW THE END OF THE BOLT
SUFFICIENTLY WITH THE M8 NUT.
STEP 5:. Insert screw (M6X85mm) through the hole of LEGS(A) ,hole A of Lower support tube and the hole of the
other LEGS(A) , fasten by M6 washer and nut. Repeat the process, insert screw (M6X85mm) through the hole of
LEGS(B) ,hole B of Lower support tube and the hole of the other LEGS(B)，fasten them by washer and nut.
LOWER SUPPORT TUBE
LEGS(A) LEGS(B)
—2—
ASSEMBLE INSTRUCTION

STEP 6: INSERT THE UPPER SUPPORTER INTO THE LOWER SUPPORT TUBE AND FINISH THE ASSEMBLING.
STEP 7: FINALLY CHECK ALL SCREWS AND NUTS CAREFULLY AND MAKE SURE ALL ARE SCREW SUFFICIENTLY.
THENTHE UNIT IS READY TO USE.
MAINTENANCE
Warning: assemble according to the manufacturer” s instructions. Check regularly for wear and
tear. Ensure fixings and anchorage is secure at all times. Check metal sections or components for
signs of corrosion. Discontinue use if weakening or breakage is found. Failure to comply with
these precautions may result in injury.
WARNING & RECOMMENDATIONS
□THIS PRODUCT MUST BE ASSEMBLED BY AN ADULT OR UNDER SUPERVISION OF
AN ADULT.
□WE RECOMMEND THAT THE SEE-SAW IS USED ON SOFT GROUND, I.e. GRASS.
□DO NOT LEAVE YOUNG CHILDREN UNATTENDED WHILST PLAYING ON THIS
SEE-SAW.
□PLEASE FASTEN THE BOLTS AND THE NUTS BEFORE TO USE THE SEE-SAW
—3—