SportsPlay Equipment 801-112 User manual

801-112 Flag Pole 15’
Page 1of 2
Rev. 04/9/2010
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
IMPORTANT
PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. Please retain
this instruction sheet in your files. It contains important replacement
parts information. All equipment must be installed in accordance with these
instructions. It is important to use and maintain all public playground
equipment properly. Playground equipment, which is improperly maintained,
can cause serious injury. Periodical inspections, maintenance, repair and/or
replacement of damaged parts is necessary for safe operation of equipment.
Appropriate publications, available at no charge, from the consumer product
safety commission, include “A Handbook for Public Playground safety”. You
can receive your free copy by calling 1-301-504-7908.
PACKING LIST
HARDWARE BAG
1
CTN
1
Hardware Bag
1
805-114
Flag Pole Top Outer Half
1
PIPE
1
803-112
1 7/8” x 18’
1
805-115
Flag Pole Top Inner Half
1
805-116
Cleat
26ft
805-117
End Weld Sash Chain #14
1
805-118
Alum Pulley
1
196-550
!” x 1 "” Roll Pin
1
216-512
5/16” x 1” B. H. Nut
1
116-535
5/16” x 1 1/2” B. H. Bolt
1
326-501
5/16” Lock Washer
2
585-904
Swivel Snap
3
805-119
1/8” “S” hook
2
186-404
!” x 1” SL FH Machine Screw
2
416-350
3/16”Socket Key
1 CTN 1 PIPE 2 TOTAL PIECES WEIGHT 85# CLASS 70

801-112 Flag Pole 15’
Page 2of 2
Rev. 04/9/2010
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
GENERAL ASSEMBLY INSTRUCTIONS:
Check all parts and hardware against the packing list to insure you have
received everything needed to assemble this product.
Check each part carefully and remove any sharp edges or projections that may
have been caused in shipping. Contact your distributor with notification of
any missing or damaged parts. Contact must be made within ten days of
receipt of your order.
Suggested Bracing Method
SPECIFIC ASSEMBLY INSTRUCTIONS:
STEP #1: Mark and dig hole. Footing is 12” around and 3 ft deep.
STEP #2: Assemble the 1 7/8” pole prior to setting it into the concrete.
Create a loop with the sash chain using one of the “S” hooks
provided. Assemble the top by placing the pulley into the half
with the sash chain around it using the !” roll pin provided, but
note that the “S” hook does not pass through the pulley. Then
bolt the top to the pole using the 5/16” x 1 1/2” B.H. Bolt with
lock washer and 5/16” B.H. nut. Attach the cleat in the pre-
drilled holes using the !” machine screws provided.
STEP #3: Prop 1 7/8” pole in holes and pour concrete. Allow at least 48
Hours for concrete to harden. If installation is on blacktop,
footings should be flush with surface and crowned slightly for
drainage. If installed in dirt, footings should be left 3” below
surface but crowned for drainage. After concrete hardens fill in
with dirt. This also applies if installation is in sand, wood
chips, or other resilient safety surface.
STEP #4: To attach flag, attach the provided swivel snaps using the 1/8”
“S” hooks to the sash chain. It is recommended to have the snaps
attached to the flag to ensure that the flag fit is correct.
MAINTENANCE INSTRUCTIONS:
Check periodically for loose bolts or broken parts. Replace any
broken or damaged parts immediately.