SSI Fluid User manual

Installation Instructions for
Dual Handle
Lavatory Faucet
Please Keep This Manual For Future Reference
Need Help?
For additional assistance or service call
Toll Free: 1 800 460 7019
Fax: [phone]
Dual Handle Lavatory Faucet/2013/V2
Sustainable Solutions International
Phone: [phone]
www.SustainableSolutions.com
IAPMO LISTED
TM
TM
This faucet meets or exceeds the following standards:
ASME A112.18.1 / CSA B125.1 / NSF61-9 / AB1953 / EPA WaterSense
Limited Lifetime Faucet Warranty
Fluid ™ warrants its faucets to be free from defects in material and workmanship for as long as the original consumer
purchaser ownshis orherhome.* This warranty applies only in original installation location.If a defect is found in normal
residential use, Fluid™
will, at its election, repair, provideareplacementpart or product, or make an appropriate adjustment.
Fluid™
reserves the right to examine the product in question and its installation prior to replacement. This warranty is limited
to replacementofdefective parts only. Damage to aproductcaused by accident, improper installation, misuse, or abuse is
not covered by this warranty. Improper care and cleaning will void the warranty.** Replacement parts can be obtained from
your local dealer or directly from the Fluid ™
warehouse. Dated proof of purchase must accompany all warranty claims. This
warranty applies only to Fluid™
faucets installed in the United States ofAmerica, Canada or Mexico (North America).
Fluid™
charges, repair or replacementcosts are expressly excluded. In no event shall the liability ofFluid ™ exceed the purchaseprice
of the faucet. Some states and provinces donot allow the exclusion or limitation of incidental or consequential damages,
™
dealer or
sales representative.
* Two year warranty on commercial applications.
** Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents or other products

1. Shut off cold and hot water supply.
2. Faucet hole should be minimum 1-1/4”
(32mm) and maximum 1-7/16”(36mm)
in diameter.
3. From above the deck, insert spout (#1)
into the center hole.
NOTE: To adjust or replace handle, unscrew
nut (#9) counter-clockwise by hand. Pull handle
(#8 or #23) up. Rotate lever handle (#8) to point
outwards, away from spout while in OFF position.
Installation Instructions
Care & Maintenance Instructions
Tools Required for Installation
SSI products are designed and engineered under strict quality standards. Regular
and proper care of our products will ensure years of trouble-free service.
For Aerator:
Regularly remove aerator(#19) with enclosed
service key (#20) and wash with clean running
water and ensure that any trapped debris has
been removed.
To clean, use a soft and damp cloth with warm
soapy water followed by rinsing with clean
water and drying with a soft cloth. Do not use
abrasive or harsh cleaners as they may result
in finish damage.
Note: Vandal resistant tilting aerator features
water saving technology (1.5gpm), swivel flow
direction adjustment by simply pushing the inside
of the aerator to direct stream.
Max flow 1.5 gpm or 5.7L/min at 60 psig
Flow pressure 15-72.5 psi
Max pressure 120 psi
Max temperature 176 °F or 80 °C
Inlet connection 1/2” NPT and 3/8” Riser
Specifications:
9. Connect SST flexible hose (#3) to valve outlet (#21).
10. Connect valves (#12) to 1/2” NPT connectors
or 3/8” (12.7mm) OD risers (not included) with
supplied coupling nuts (#18) and washers (#17).
Right hand valve is for cold water and left valve
is for hot water supply.
11.Please follow enclosed instruction for push type
drain (#22) installation, if drain comes with this
package.
7. From underneath the deck, slide gaskets
(#13) and washers (#14) onto handle sets (#24),
then hand tighten nuts (#15). Finally tighten
locking screws (#16) with a screw driver.
Note: Make sure SST flexible hoses (#3) are
free of kinks when they’re connected to valve
outlet (#21).
6. From above the deck, insert pre-assembled
handle sets (#24) into hole and make sure red
or blue dot facing you OR the lever handle
points outward when in OFF position. HOT
valve body tagged with a red label should be
on the left side, and COLD valve body indicated
with slots which can be seen after removing
handle (#8) and base (#10) on the right side.
5. Remove nuts (#15), washers (#14) and
gaskets (#13) from handle sets (#24).
8. Once handle set is properly set in position, care-
-fully peel off red and blue dot off from handle.
To replace with cross handle (#23 not included).
Rotate cross handle (#23) until the letter “C” or “H”
faces you while in OFF position. Finally hand
tighten nut (#9) to secure handle (#8 or #23).
Note: “C” handle is on right and “H” handle on
left side.
4. From underneath the deck, slide gasket
(#4) and plate (#5) over mounting rods (#2).
Screw and tighten mounting nuts (#6) by
using a supplied wrench tool (#7).
For Cartridge:
For Surface Finish:
Remove mounting nut (#15), plate (#14) and
gasket (#13) and pull up handle set (#24).
Loosen nut (#9) by hand and pull handle (#8
or #23) up. Unscrew handle base (#10) from
valve body. Use an adjustable wrench to
loosen cartridge (#12). Ensure cartridge is clean
and free of blockages. Replace it if damaged.
Adjustable Wrench
Allen Wrench
Screw Driver
Teflon Tape