Stirling JK-149-WHT User manual

INSTRUCTION MANUAL
1.7L Kettle
E209
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018
Model Number JK-149-WHT

2
Welcome
Congratulations on choosing to buy a STIRLING®product.
All products brought to you by STIRLING®are manufactured to the highest
standards of performance and safety and, as part of our philosophy of
customer service and satisfaction, are backed by our comprehensive
3Year Warranty.
We hope you will enjoy using your purchase for many years to come.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

3
02 Welcome
04 Warranty Details
05 General Safety Instructions
08 Product Overview
09 Getting Started
10 Instructions
11 FAQs and Troubleshooting Guide
12 Other Useful Information
15 Repair and Refurbished Goods or Parts Notice
Contents
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

4
YEAR WARRANTY
3
1.7L Kettle
The product is guaranteed to be free from defects in workmanship and parts for
a period of 36 months from the date of purchase. Defects that occur within this
warranty period, under normal use and care, will be repaired, replaced or refunded
at our discretion. The benefits conferred by this warranty are in addition to all
rights and remedies in respect of the product that the consumer has under the
Competition and Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and to compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

5
General Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before rst use, even if you are familiar with this type of
product. The safety precautions enclosed herein reduce the risk of re, electric shock
and injury when correctly adhered to. Keep the manual in a safe place for future
reference, along with the completed warranty card, purchase receipt and carton. If
applicable, pass these instructions on to the next owner of the appliance.
Always follow basic safety precautions and accident prevention measures
when using an electrical appliance, including the following:
Electrical safety and cord handling
• Voltage: Before connecting the kettle to the power supply, make sure your
outlet voltage and circuit frequency correspond to the voltage indicated on the
appliance rating label and your outlet socket is properly earthed. If this is not
the case, do not use the kettle.
• Separate circuit: Do not use any other appliance at the same time on the same
electrical circuit as it may overload the circuit and blow the fuse or breaker.
• Water: To protect against fire and electric shock, do not immerse the cord,
plug, power base or the kettle itself in water or other liquid. Do not expose the
electrical connections to water.
• Base: Only use the kettle with the power base provided. Do not use the power
base to power any appliance other than this kettle.
• Keep dry: Avoid spillage on the connector.
• Power cord: Do not kink, bend, squash, strain or damage the power cord and
protect it from sharp edges and heat. Do not let the cord hang over the edge of
a table or benchtop. Do not let it touch hot surfaces. The cord should be run in
such a way that there will be no risk of anyone pulling it inadvertently.
• No extension cord: Do not use an extension cord with this kettle.
• Damage: Do not pick up or operate the appliance if the power supply cord,
plug, power base or kettle housing is damaged, or after it malfunctions or has
been damaged in any manner.
• WARNING: A damaged cord or plug must be replaced by the manufacturer or a
qualified person in order to avoid a hazard. In case of damage, contact our after
sales support centre for advice.
• RCD: Unless your home is already fitted with a residual current device (safety
switch), we recommend installing a residual current device to lessen the risk
of scalding or other injury from hot water, which may be ejected if the heating
element ruptures. Contact a qualified electrician for advice.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

6
General Safety Instructions (Cont.)
Usage conditions and restrictions
• Domestic use only: This appliance is intended for private household use only.
It is not intended for commercial/industrial or trade use. Do not use it outdoors.
• Purpose: Do not use this kettle for anything other than its intended purpose,
and only use it as described in this manual. Do not use the kettle to boil
anything other than water. Any other use is not recommended and may cause
fire, electric shock or injury.
• No timer: This appliance is not intended to be operated by means of an
external timer or separate remote control system.
• Boiling empty: Do not use the kettle without water in it to avoid damaging
the heat elements. The elements must be fully immersed (unless concealed).
Should you accidentally allow the kettle to operate without water, the boil-dry
protection will automatically switch it off. In such a case, allow the kettle to
cool before filling with cold water and reusing it.
• Accessories: The use of accessory attachments not recommended here may
result in fire, electric shock or personal injury, and will void your warranty.
• Misuse of the appliance may result in potential injury, risk of fire and/or electric
shock. We accept no liability for any eventual damages or injury caused by
misuse of the product or noncompliance with the instructions.
• Usage restriction: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliances by a person responsible for their safety.
• Children: Supervise children to ensure they do not play with the kettle. Close
supervision is necessary when any appliance is used by or near children.
Safe usage
• Flat surface: When using the kettle, place it on a stable, secure, dry and level
surface, out of children's reach, to prevent damage or injury from the kettle over-
turning. CAUTION: Do not operate the kettle on an inclined plane.
• DO NOT operate the kettle under the following conditions:
* In a damp place or in areas with high humidity (such as in a bathroom)
* On or near a hot cooktop, in a heated oven, or near an open flame.
* On a metal tray.
* In confined spaces or under overhanging furniture/structures.
• Filling: Lift the kettle off the power base to fill it. Never fill the kettle while it sits
on its base or while it is switched on to avoid spillage on the connector. If the
power base unit becomes wet, unplug it before wiping it dry.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

7
General Safety Instructions (Cont.)
• Do not overfill the kettle to avoid splattering and ejection of boiling water.
Make sure the water level is between the minimum and maximum levels.
• Spout: Position the kettle so the spout is directed away from you.
• Filter: The filter is built into the lid and cannot be removed. Do not operate the
kettle without the lid fitted.
• Before switching on, make sure the kettle is located properly on the power
base and the lid is securely closed, otherwise it may not switch off.
• Unattended: Do not leave the kettle unattended when the power is turned on.
• CAUTION: Ensure the kettle is switched off before removing it from the base.
Do not move the appliance while it is switched on.
• Disconnect: Always unplug the kettle from the outlet when it is not in use. To
disconnect, turn off the power at the outlet, then remove the plug from the wall.
Grip the plug when disconnecting, do not pull the cord.
• CAUTION: Unplug the kettle and allow it to cool before cleaning and mainte-
nance. To prevent damage to the appliance, do not use abrasive or alkaline
cleaning agents when cleaning. Use a soft cloth and a mild detergent.
• Cleaning: Rinse the inside of the kettle regularly and descale the appliance
when necessary. Refer to page 12 for comprehensive descaling instructions.
CAUTION: HOT SURFACES!
• Kettle surfaces: Do not touch any part of the kettle housing when it is in use.
The surfaces get hot. Only touch the handle. Do not put any part of your hand
or body near the kettle when it is turned on.
• Residual heat: Take care when handling the kettle after use. The inside surface
which conceals the heating element is subject to residual heat after use. Water
can also remain hot for a considerable time after boiling and can present a
scald hazard.
• WARNING: Do not remove the lid while the water is boiling. Keep the lid closed
while the water is boiling and straight afterwards. Scalding may occur if the lid
is removed while the water is heating up. Be careful when opening the lid for
refilling when the kettle is hot.
• Steam: While water is boiling, or just after the water has finished boiling, avoid
contact with the steam from the spout.
• Hot water: Use extreme caution when moving the kettle containing hot water.
Always take care when pouring hot water. Tilt the kettle slowly and carefully
without tipping it too fast.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

8
Product Overview
NOTE: Due to continued product improvement, images and illustrations in this manual
may vary slightly from the product purchased. All images in this manual are for reference
purposes only. Parts are not necessarily pictured to scale.
A Cordless kettle
1 Spout
2 Lid (with in-built filter)
3 Handle
4 Transparent water gauge
5 On/Off switch with indicator light
6 Power base with cord and plug
B Documentation (not shown):
Instruction manual, Quick start guide, Warranty certicate
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018
Scope of delivery
1
2
4
3
5
6

9
Before first use
• Packaging: This product has been packaged to protect it against transportation
damage. Unpack the appliance and keep the original packaging carton and
materials in a safe place. It will help prevent any damage if the product needs
to be transported in the future, and you can use it to store the appliance when it
is not in use. In the event that the carton is to be disposed of, please recycle all
packaging materials where possible.
Plastic wrapping can be a suffocation hazard for babies and young children, so
ensure all packaging materials are out of their reach and disposed of safely.
• Cord: Unwind the power supply cord to its full length and inspect the cord
and plug for damage. Inspect all other parts of the appliance for visual damage.
Do not use the appliance if anything appears to be damaged or not working
properly. In case of damage, contact our after sales support centre.
• Documentation: Make sure you have read and understood all instructions and
warnings in this manual. Refer to the Product Overview, opposite, to familiarise
yourself with the product and identify all parts. Pay particular attention to the
safety instructions on the previous pages.
• Preliminary use: Place the kettle on a stable, dry and level work surface, away
from the edge. Make sure the ON/OFF switch is in the OFF position (up). In
order to ensure that dust and oils left from the manufacturing process and
transport are removed, boil some water a few times before using the kettle.
Lift the kettle vertically off the power base and remove the lid: grip it by the lid
knob and pull it straight up.
Fill the kettle with cold water. When replacing the lid, press it down firmly and
make sure the in-built filter sits behind the spout and the two cut-outs in the
lid fit over the two protrusions on the edge of the kettle.
Replace the kettle on the power base, switch it on and boil the water, then
discard the water (detailed usage instructions are provided on page 10).
Repeat this procedure twice before using the kettle to boil water for
consumption.
Getting Started
Boil-dry protection
The kettle has an automatic shut-off feature that shuts down power to
the kettle if it is empty, preventing accidental operation without water.
Once this safety feature has been activated, unplug the kettle and let it cool
(for at least 15 minutes) so the fail-safe device will reset itself.
Then fill the kettle with cold water and use it as normal.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

10
Using the kettle
• Positioning the power base: Position the base as close to a wall socket as
possible. Route the power cord so that it does not overhang the work surface
and cannot be caught accidentally. Shorten the cord by winding it round the
cord storage area under the base and lead it out through the cord exit slot.
• Filling: Remove the lid from the kettle: grip it by the lid knob and pull it straight
up. Fill the kettle with the desired amount of cold tap water. When replacing the
lid, press it down firmly and ensure the in-built filter sits behind the spout and
the two cut-outs in the lid fit over the two protrusions on the edge of the kettle.
Please align the arrow with the spout for a perfect fit.
Make sure to fill the kettle at least to the minimum but not beyond the maximum
level. Too little water will result in the kettle turning off before the water has
boiled (because of the boil-dry protection). Too much water will result in boiling
water spilling out of the spout when boiling.
• Positioning the kettle: Before positioning the kettle on the power base, ensure
the lid is securely in place and the On/Off switch is in the Off position (lift the
kettle off the base and set it down again). Then place the kettle on the power
base so that any steam is directed away from you, taking care not to spill any
water onto the base.
• Switching on: With dry hands, plug the power base into an appropriate wall
outlet and turn on power at the outlet.
Press the On/Off switch down. The power indicator light will light up and the
water will start heating up. Do not open the lid during use. The kettle will
automatically turn itself off when the water has boiled.
• Pouring: Wait until the water has completely stopped bubbling before pouring.
Grip the handle and lift the kettle off the power base.
CAUTION: Take care when pouring the water to avoid scalding from boiling
water or hot steam. Do not open the lid while the water in the kettle is hot.
• Stop heating: To stop the heating process any time during operation, push the
On/Off switch upwards to the Off position, or simply lift the kettle off the base.
• Re-boiling water: To re-boil the water, allow the kettle to cool for 15–20
seconds before pressing the On/Off switch down again.
• After use: The kettle may be stored on the power base, but make sure the
power supply is turned off when the kettle is not in use.
Instructions
CAUTION!
Take care when pouring boiling water to avoid scalding. Do not open the lid while
the water in the kettle is hot. If refilling after boiling water is required, pull the lid
straight up and move it out of the steam as soon as it separates from the kettle.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

11
FAQs and Troubleshooting Guide
Problem / Question Solution / Answer
The ON/OFF switch will
not stay down when I
want to boil water.
If you have just boiled water, wait for 15–20 seconds
to let the kettle cool. The On/Off switch should then
stay down when pressing it. Also ensure that the
switch is free of obstructions.
The kettle's power base
got damaged. Can I use
the kettle on a cooktop?
No, never place the kettle on a cooktop. Only use it
with the supplied power base.
Why is the specified
maximum fill mark at
1.7L when more water
fits inside?
Although the kettle holds more water, do not fill it
past the maximum marking as water needs space
for expansion when heating and boiling. Overfilling
the kettle will result in boiling water spilling out of the
spout when boiling.
My kettle does not
switch off automatically.
Can I still use it and
switch off manually?
No, if the kettle does not switch off automatically, the
temperature control may be faulty. Do not use the
kettle. Contact our after sales support centre for ad-
vice on examination and return or repair of the kettle.
Also make sure that the switch is free of obstructions;
the kettle will not turn off if the switch is constrained.
The kettle is getting
noisier as the water is
heating. Does that mean
something is wrong?
No, all kettles make a noise while heating up water.
The noise will increase as the water reaches boiling
point, but will abate afterwards.
How often do I need to
descale my kettle?
If you live in a hard water area, you may need to
descale the kettle every few months, or if obvious
scaling has taken place. In a soft water area,
descaling may be required less frequently, or not
at all. If a whitish deposit has accumulated on the
bottom of the kettle or along the sides, or spots of
what looks like rust, scaling has taken place and you
need to descale the appliance – see page 12.
Moisture on the power base
When you lift the kettle off the base, you may see moisture on the surface of the
base. This is the steam used to switch the kettle off automatically, which then
condenses and escapes via the vents on the underside of the kettle. Do not lift
the kettle backwards, as this may allow water to pass through the steam aperture
onto the control area. Should this occur, you must let the kettle dry before use.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

12
Other Useful Information
Cleaning and care
WARNING!
• Switch the kettle off, unplug the power base from the wall socket and let the
kettle cool down completely before cleaning or descaling.
• Never immerse the kettle, cord or power base in water. All connections and
sockets must be kept dry.
• To prevent damage to the kettle, do not use scouring pads, steel wool,
solvents or harsh chemical or alkaline cleaning agents when cleaning, use a
soft cloth and a mild detergent only.
The outside of your kettle only requires occasional wiping with a damp cloth and
mild, non-abrasive household detergent, if necessary. Polish with a soft dry cloth.
Descaling (removal of mineral deposits)
From time to time, you may need to clean off any mineral deposits (limescale)
left by water inside your kettle to keep it operating efficiently. Scale build-up will
cause the element to overheat, reducing its working life. It may also cause the
safety cut-out to operate prematurely, switching the kettle off before the water
boils. As the element is mounted beneath the kettle, limescale can only build up
on the walls and floor of the kettle, where it can be seen and dealt with.
To minimise scale build-up:
• Empty the kettle after each use; do not let water stand in the kettle overnight.
• Use filtered instead of ordinary tap water, if scaling is problem in your area.
• Descale the kettle regularly using a proprietary brand of descaler suitable
for use in plastic-bodied products and follow the instructions on the packet. In
areas of very hard water, descaling may be necessary as often as once a month.
• When descaling has finished, empty the kettle and rinse it out several times
with fresh water, then fill with fresh water, boil, and discard the water. This
should ensure no chemical residues are left in the kettle.
• Alternatively, clean the inside of the kettle with an equal part solution of
household (white) vinegar and water:
Descaling with water and vinegar:
* Fill the kettle with 3 cups of white vinegar and the remainder with water.
* Let this mixture stand in the kettle overnight. Do not boil.
* Empty the solution from the kettle.
* Remove any stains remaining by rubbing with a damp cloth.
* Fill the kettle with fresh, clean water, let it boil and then discard the water.
* Repeat with clean, fresh water until all traces of vinegar are removed.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

13
Other Useful Information (Cont.)
Cleaning the lid and filter
Any scale particles that remain suspended in your water supply may give it a
cloudy or greasy appearance, depending on the hardness of the water. The filter
built into the lid of your kettle will prevent these particles passing into your drink.
You must ensure that the filter is kept clean and clear of deposits, otherwise the
performance of your kettle may be adversely affected, your drinks may contain
scale particles, and the water inside the kettle may look cloudy.
Clean the anti-scale filter regularly, or whenever you notice any deposits left on it,
and especially if pouring is affected in any way. The filter is located within the lid
of the kettle. It is not removable.
WARNING!
Before cleaning the lid and filter, make sure the power base is switched off and
unplugged and the kettle is empty and completely cool.
• To clean the filter, prepare a descaling solution in a small bowl, following the
"Descaling" instructions and using hot water and a proprietary descaling
solution, vinegar or lemon juice.
• Remove the lid from the kettle and place it with the filter side in the bowl. Do not
immerse the lid entirely. Leave the filter soaking in the solution for five minutes.
• Gently rub off any limescale residues with your fingers and then rinse the filter
thoroughly.
• Replace the lid onto the kettle. Never operate the kettle without the lid in place.
Storage
• Before storing the appliance, make sure it is dry and unplugged.
• When in storage or not in use, the power cord may be wound around the cord
storage underneath the power base.
• Store the kettle in the original carton, which will protect it from dust, in a clean
and dry place, out of children's reach.
Descaling with water and lemon:
* Half-fill the kettle with tap water and add the juice of 1 lemon.
* Boil this mixture and let it stand for 15 minutes before discarding.
* Fill the kettle with fresh, clean water, let it boil and then discard the water.
* Repeat with clean, fresh water until all traces of lemon are removed.
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

14
Other Useful Information (Cont.)
Technical specifications
Capacity: 1.7L
Power: 1850–2200W, 220–240V ~, 50–60Hz
Power base: 360° Rotational power base for cordless operation
Heating element: Concealed
Safety features: Boil-dry & overheating protection
Automatic switch-off
Weight (approx.): 1.390kg
Dimensions (approx.): H250 x D180 x L220 mm
Compliance
This appliance has been fully tested and meets all requirements as set out by
standards AS/NZS 60335.1 and AS/NZS 60335.2.15.
Service, repair and spare parts
• Do not attempt to repair, disassemble or modify the kettle or power base.
The unit contains no user-serviceable parts inside and there are no spare parts
available for purchase.
• If you have any problems with the kettle, contact our after sales support centre
for advice on repair or replacement.
Responsible disposal
At the end of its working life, do not throw this appliance out with your household
rubbish. Electrical and electronic products contain substances that can have
a detrimental effect on the environment and human health if disposed of
inappropriately. Observe any local regulations regarding the disposal of electrical
consumer goods and dispose of it appropriately for recycling. Contact your local
authorities for advice on recycling facilities in your area.
The RCM Mark (Regulatory Compliance Mark) indicates that the product
complies with the relevant guidelines of the ACMA as well as corresponding
government requirements for the safety of electrical devices.
E209
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

15
Repair and Refurbished
Goods or Parts Notice
Unfortunately, from time to time, faulty products are manufactured which need to
be returned to the supplier for repair.
Please be aware that if your product is capable of retaining user-generated data
(such as files stored on a computer hard drive, telephone numbers stored on
a mobile telephone, songs stored on a portable media player, games saved on
a games console or files stored on a USB memory stick) during the process of
repair, some or all of your stored data may be lost. We recommend you save this
data elsewhere prior to sending the product for repair.
You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refurbished parts in the repair process.
Please be assured though, refurbished parts or replacements are only used
where they meet ALDI’s stringent quality specifications.
If at any time you feel your repair is being handled unsatisfactorily, you may
escalate your complaint. Please telephone us on 1300 886 649 or write to us at:
Tempo (Aust) Pty Ltd ABN 70 106 100 252
PO BOX 6056 Frenchs Forest, Sydney, Australia NSW 2086
Telephone: [phone] (Aust) - Fax: [phone]
Tempo Help Desk: 1300 886 649 (Aust)
(Operating Hours: Mon-Sat 09:00am to 06:00pm AEST)
Email: [email protected]g
YEAR WARRANTY
3
1.7L Kettle
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018

Warranty returns
Should you for any reason need to return this product for
a warranty claim, make sure to include all accessories with
the product.
Product does not work?
If you encounter problems with this product, or if it fails to
perform to your expectations, make sure to contact our
After Sales Support Centre on 1300 886 649 for advice.
For an electronic copy of this manual, go to www.stirlingappliances.com.au and download a copy.
Instruction Manual Revision Index
Version No Issue Date Description
V1.0 06 September 2018 Original release
V1.1 14 September 2018 Minor update, page 10
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: JK-149-WHT PRODUCT CODE: 63379 12/2018