Sundown Audio SAZ-1000D User manual

SAZ-1000D
SAZ-1500D
SAZ-3000D
Owner's manual

-2-
Congratulations on your purchase of a Sundown Audio high performance car audio
amplifier. Your new amplifier has been built to the highest standards of quality and
is intended to serve you for years to come.
Visit us online at http://www.sundownaudio.com
WARRANTY:
Your new Sundown Audio amplifier is covered by a 2 year limited warranty if
purchased from an authorized Sundown Audio dealer. This warranty does not
cover improper installation, accidental damage, misuse, abuse, improper
wiring, operation of unit outside of listed specifications, or any product that
has been modified or repaired by anyone other than Sundown Audio. This
warranty is transferrable provided the original invoice or receipt is still
with the unit so that its new owner can prove date and place of purchase.
All warranty returns must be sent freight prepaid to Sundown Audio and be
accompanied by the original sales invoice or receipt. For faster warranty
service please contact us at [email protected] to request a
return authorization code. At the sole discretion of Sundown Audio your
amplifier will be either repaired or replaced.
If no defect is found and the unit must be shipped back the customer is
responsible for return freight, if the unit is truly defective the replaced or
repaired unit will be shipped back prepaid. In the event of shipping damage
due to improper packaging of the return the customer is liable for the cost
of all damages, necessary repairs, or replacement. Be sure to properly pack
your return!
Sundown Audio also offers a 5 year guarantee to our customers for a
discounted replacement unit. We are so certain of the quality of our equipment
that even if you are at fault for causing damage to your amplifier we will offer
you a new unit at a reduced cost compared to MSRP. Contact us via e-mail to
take advantage of this offer, even though we doubt you will ever need to!
This offer applies ONLY to the original purchaser of the unit and is not
transferrable like the 2 year limited warranty. As is the case with standard
warranty claims the return MUST be sent prepaid and with a copy of the
original invoice or receipt.
RETURN ADDRESS:
Sundown Audio
ATTN: WARRANTY SERVICE
151 Rebel Hill DR.
Mooresville NC, 28115

Features
-3-
Double Sided Through Hole Epoxy PCB
Daisy-Chain Through Output RCA
Efficiency : 86% @ 4 ohm, at 100Hz
24dB/Oct Variable Crossover
Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
Variable Subsonic Filter
Variable Bass Boost
Variable Low Pass Filter
Variable Phase Shift
Four(4) Gauge Power Supply Connectors
Tested Voltage & THD : 14.4V & Less than 1% THD
Operating Voltage : DC 10V~16V
Digital Class-D Linkable Mono Block Amplifier
1 Ohm Stability
RCA Line Input and Master Output
24dB Octave Crossover Slope
Wired Remote Controller
Double Sided Through Hole Epoxy PCB
Daisy-Chain Through Output RCA
Efficiency : 86% @ 4 ohm, at 100Hz
24dB/Oct Variable Crossover
Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
Variable Subsonic Filter
Variable Bass Boost
Variable Low Pass Filter
Variable Phase Shift
Zero(0) Gauge Power Supply Connectors
Tested Voltage & THD : 14.4V & Less than 1% THD
Operating Voltage : DC 10V~18V
Digital Class-D Linkable Mono Block Amplifier
1 Ohm Stability
RCA Line Input and Master Output
24dB Octave Crossover Slope
Wired Remote Controller
SAZ-1000D
SAZ-1500D
Double Sided Through Hole Epoxy PCB
Daisy-Chain Through Output RCA
Efficiency : 86% @ 4 ohm, at 100Hz
24dB/Oct Variable Crossover
Multi-Way Protection Circuitry
(Thermal/Over Current/Speaker Short/Speaker DC Protection)
Variable Subsonic Filter
Variable Bass Boost
Variable Low Pass Filter
Variable Phase Shift
Zero(0) Gauge Power Supply Connectors
Tested Voltage & THD : 14.4V & Less than 1% THD
Operating Voltage : DC 10V~18V
Digital Class-D Linkable Mono Block Amplifier
1 Ohm Stability
RCA Line Input and Master Output
24dB Octave Crossover Slope
Wired Remote Controller
SAZ-3000D

Rated power output
-RMS power, 2 ohm linkable/dual mono ------
-RMS power, 1 ohm mono ------------------------
-RMS power, 2 ohm mono ------------------------
-RMS power, 4 ohm mono-------------------------
Signal to Noise Ratio -----------------------------------
Low pass frequency crossover ---------------------
Subsonic filter ----------------------------------------------
Bass boost @ 45Hz -------------------------------------
Phase shift control----------------------------------------
Frequency response--------------------------------------
T.H.D @ 4 ohm----------------------------------------------
Efficiency @ 4 ohm-----------------------------------------
Fuse rating---------------------------------------------------
Input Sensitivity -------------------------------------------
Dimensions---------------------------------------------------
1800W x 1CH
1000W x 1CH
600W x 1CH
300W x 1CH
>90dB
35Hz~300Hz
10Hz~60Hz
0~18dB
0~180 degree
10Hz~350Hz (+/- 1dB)
<0.1%
86%
25A x 3
200mV to 6V (+/- 5%)
252(W) x 58(H) x 294(L)mm
Rated power output
-RMS power, 2 ohm linkable/dual mono ------
-RMS power, 1 ohm mono ------------------------
-RMS power, 2 ohm mono ------------------------
-RMS power, 4 ohm mono-------------------------
Signal to Noise Ratio -----------------------------------
Low pass frequency crossover ---------------------
Subsonic filter ----------------------------------------------
Bass boost @ 45Hz -------------------------------------
Phase shift control----------------------------------------
Frequency response--------------------------------------
T.H.D @ 4 ohm----------------------------------------------
Efficiency @ 4 ohm-----------------------------------------
Fuse rating---------------------------------------------------
Input Sensitivity -------------------------------------------
Dimensions---------------------------------------------------
6000W x 1CH
3000W x 1CH
1600W x 1CH
800W x 1CH
>90dB
35Hz~300Hz
10Hz~60Hz
0~18dB
0~180 degree
10Hz~350Hz (+/- 1dB)
<0.1%
86%
300A (external type fuse)
200mV to 6V (+/- 5%)
252(W) x 53(H) x 594(L)mm
Specifications
SAZ-1000D
SAZ-1500D
SAZ-3000D
Rated power output
-RMS power, 2 ohm linkable/dual mono ------
-RMS power, 1 ohm mono ------------------------
-RMS power, 2 ohm mono ------------------------
-RMS power, 4 ohm mono-------------------------
Signal to Noise Ratio -----------------------------------
Low pass frequency crossover ---------------------
Subsonic filter ----------------------------------------------
Bass boost @ 45Hz -------------------------------------
Phase shift control----------------------------------------
Frequency response--------------------------------------
T.H.D @ 4 ohm----------------------------------------------
Efficiency @ 4 ohm-----------------------------------------
Fuse rating---------------------------------------------------
Input Sensitivity -------------------------------------------
Dimensions---------------------------------------------------
3000W x 1CH
1500W x 1CH
800W x 1CH
400W x 1CH
>90dB
35Hz~300Hz
10Hz~60Hz
0~18dB
0~180 degree
10Hz~350Hz (+/- 1dB)
<0.1%
86%
40A x 4
200mV to 6V (+/- 5%)
252(W) x 58(H) x 434(L)mm
-4-

MaxMin
GAIN
60Hz
10Hz
SUBSONIC BASS BOOST
18dB
0dB
300Hz
35Hz 180
0
LPF
POWER
PROTECTION
CLASS-D LINKABLE MONO BLOCK amplifier
REMOTE
PHASE
IN PUT BR OUT
BR IN
IN PUT
MaxMin
GAIN
60Hz
10Hz
SUBSONIC BASS BOOST
18dB
0dB
300Hz
35Hz 180
0
LPF
POWER
PROTECTION
CLASS-D LINKABLE MONO BLOCK amplifier
REMOTE
PHASE
IN PUT BR OUT
BR IN
IN PUT
MaxMin
GAIN
60Hz
10Hz
SUBSONIC BASS BOOST
18dB
0dB
300Hz
35Hz 180
0
LPF
POWER
PROTECTION
CLASS-D LINKABLE MONO BLOCK amplifier
REMOTE
PHASE
IN PUT BR OUT
BR IN
IN PUT
-5-
HEAD UNIT
Single Amp Input Connection
to SLAVE UNIT "BR IN"
* BR OUT (BRIDGEABLE OUTPUT)
* BR IN (BRIDGEABLE INPUT)
Dual Amp Input Connection (MASTER & SLAVE RCA Connection)
"MASTER UNIT"
"SLAVE UNIT"
RCA Connection
HEAD UNIT
Wired Remote Controller
Wired Remote Controller
SAZ-1000D / SAZ-1500D / SAZ-3000D

POWER
SPEAKER
GND REM B+
Caution
This amplifier is not supplied
with internal fuse in itself.
Make sure you install in-line
fuse holder from
the terminal of battery.
-6-
Power Connection
+12V Power
Connect the +12V terminal of the amplifier to the + terminal of the battery
using a large gauge power wire (preferably 1/0 gauge). It iscritical to utilize
an in-line fuse within 8 inches of the battery to ensure safe operation of the
amplifier. Make sure that the fuse isnot installed while you are connecting
the + wire to the battery terminal to avoid sparking and possible injury or
damage.
GROUND
Disconnect the battery and connect the GND (ground) terminal to the cars
chassis. Keep this cable as short as possible (not longer than 10 inches).
Be certain that the chassis ground point is free of rust, paint, and grime
to ensure a solid electrical connection.
REMOTE
Connect the REM terminal to either the remote output lead from the radio
or another switched 12V supply such as the power antenna wire.
First make the ground connection, then +12V wire connection and finally
the remote connection. Furthermore, the +12V wire must always be fused
at the battery for protection against possible damage. If you need to replace
the power fuse, replace it with a fuse of the same value. It may result in
a serious hazard to use a fuse of a different type or rating.
Caution
Caution
This amplifier is not supplied with internal fusein itself.
Make sure you install in-line fuse holderfrom
the + terminal of battery. Recommend 300 Ampere fuse.
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
POWER
GND REM B+
FUSE
B+REMGND
POWER FUSE
SAZ-1000D SAZ-1500D
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
SAZ-3000D
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
To +12V DC
BATTERY

POWER
SPEAKER OUTPUT
GND REM B+
FUSE
BA
B+REMGND
POWER FUSE POWER
-7-
1~4
ohms
++
--
++
--
2~8
ohms
2~8
ohms
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
SAZ-1000D
POWER
SPEAKER OUTPUT
GND REM B+
FUSE
BA
B+REMGND
POWER FUSE POWER
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
1~4
ohms
++
--
++
--
++
--
2~8
ohms
2~8
ohms
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
SAZ-1500D
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
Single Amp Power and Speaker Connection
++
--

POWER
SPEAKER
GND REM B+
Caution
This amplifier is not supplied
with internal fuse in itself.
Make sure you install in-line
fuse holder from
the terminal of battery.
POWER
SPEAKER
GND REM B+
Caution
This amplifier is not supplied
with internal fuse in itself.
Make sure you install in-line
fuse holder from
the terminal of battery.
-8-
1~4
ohms
++
--
++
--
++
--
Single Amp Power and Speaker Connection
2~8
ohms
2~8
ohms
300A (External Type Fuse)
Recommended Ampere
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
300A (External Type Fuse)
Recommended Ampere
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
SAZ-3000D

BA
B+REMGND
POWER FUSE POWER
Dual Amp Power and Speaker Connection
-9-
Use 8 Gauge(AWG) wire cable
POWER
SPEAKER OUTPUT
GND REM B+
FUSE
BA
B+REMGND
POWER FUSE POWER
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
SAZ-1000D
POWER
SPEAKER OUTPUT
GND REM B+
FUSE
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
SAZ-1500D
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
2~8
ohms
Use 8 Gauge(AWG) wire cable
2~8
ohms
"MASTER UNIT"
"SLAVE UNIT"
"MASTER UNIT"
"SLAVE UNIT"
++
--
++
--

POWER
SPEAKER
GND REM B+
Caution
This amplifier is not supplied
with internal fuse in itself.
Make sure you install in-line
fuse holder from
the terminal of battery.
POWER
SPEAKER
GND REM B+
Caution
This amplifier is not supplied
with internal fuse in itself.
Make sure you install in-line
fuse holder from
the terminal of battery.
Use 8 Gauge(AWG) wire cable
"MASTER UNIT"
"SLAVE UNIT"
2~8
ohms
-10-
Using a dual amplifier configuration, the MASTER amplifier has total control
over the SLAVE amplifier. When using dual amplifier to operate subwoofer,
the positive terminal of the subwoofer's voice coil must be connected to
the positive terminal of the MASTER Amplifier and the negative terminal of
the subwoofer's voice coil must be connected to positive terminal of
the SLAVE Amplifier. Be advised that the dual amplifier configuration has
tremendous output potential, so ensure that your subwoofers can handle
such a large amount of power.
When utilizing the dual amplifier configuration it is important
to note that the connected speaker load can be no lower
than 2 ohms. Connecting a lower impedance load can damage
the amplifier and void your warranty
Caution
300A (External Type Fuse)
Recommended Ampere
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
300A (External Type Fuse)
Recommended Ampere
To +12V DC
to REMOTE Turn-on
from HEAD UNIT
CAR STEREO HEAD UNIT
GROUND
BATTERY
Dual Amp Power and Speaker Connection
SAZ-3000D
++
--

This power amplifier has protection features to prevent any damages from misuse or faulty
conditions. If the unit senses excessive heat, short circuited speakers or overload, the
protection indicators will light, and the system will be turned off. In order to check the
occurred problem, you should turn all levels down and all power off and carefully check the
installation for wiring mistakes or short. If the amplifier shuts down due to excessive heat,
the protection indicators will not light : simply allow time for the unit to cool.
Before removing your amplifier, refer to the list below and follow the suggested procedures.
Always test the speakers and their wires first.
PROTECTION LED ILLUMINATES WHEN AMPLIFIER IS POWERED UP
FUSE BLOWING
OVERHEATING
Check that the minimum speaker impedance is correct.
Check speaker shorts.
Check that there is a good airflow around the amplifier.
Check a good ground and for speaker shorts.
Disconnect all RCA inputs from the amplifier. If hiss/noise disappears, check
it with a good RCA interconnect. Then check the component driving the
amplifier.
SOUND TOO LOW-DISTORTED SOUND
Check that the input level control is set to match the output level of the unit.
Check the head unit volume.
Check speaker shorts.
Check that crossover frequencies have been properly set.
HIGH HISS-ENGINE NOISE IN SPEAKERS
Check that the minimum speaker impedance is correct.
Check short on power cable and vehicle chassis.
AMPLIFIER IS NOT POWERED UP
Check that there is battery power on the +12V terminal.
Check that remote terminal has at least 13.8V DC remote connection.
Check a good ground connection. Check all fuses.
Check the protection LED is not lit.
Check shorts on speaker wires.
Remove speaker wires and reset the amplifier. If the protection LED still
comes on, then the amplifier is faulty.
Trouble Shooting
-11-

MADE IN KOREA