Sunmi M2 User manual
This device complies with Part 15 of the FCC Rules. Operation
is
subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: 2AH25M2
NOTE: Changes
or
modifications
not
expressly approved by the
party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if
not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which
can be
determined by turning the equipment
off and
on, the user is encouraged to try to correct the interference by one
or
more of the following measures:
---Reorient
or relocate the receiving antenna.
---Increase
the separation between the equipment and receiver.
---Connect
the equipment into
an
outlet
on a circuit
different
from
that to which the receiver is connected.
---Consult
the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
With RF exposure requirements, a minimum separation distance
of
1.0cm must be maintained between the user’s body and the handset,
including the antenna.
Third-party belt-clips,
holsters, and similar including the antenna.
Third-party belt-clips,
holsters, and similar accessories used by
this
device should not contain any metallic components.
Body-worn
accessories that do not meet these requirements may not comply
with
RF exposure requirements and should be
avoided
.
Specific Absorption Rate
(SAR)
information:
This wireless phone meets the government's requirements for exposure
to radio waves. The guidelines are based on standards that were
developed by independent
scientific
organizations through periodic
and
thorough evaluation
of scientific
studies. The standards include
a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
FCC RF Exposure Information and Statement. The SARlimit of USA
(FCC) is 1.6W/kg averaged over one gram of tissue.
Device types:
T8900&T8901
has also been tested against this SAR
limit. The highest SARvalue reported under this standard during
product
certification when properly worn
on
the body
is
1.363W/kg
(1gSAR，
test
distance：5mm，limit 1.6W/kg).
This
device was tested
for
body-
worn operations with the back of the handset kept 5mm from the body.
To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 5mm separation distance between the
user's body and the back of the handset. The use of belt clips, holsters
and similar accessories should not contain metallic components in its
assembly. The use
of
accessories that do not satisfy these requirements may not comply
with
FCC RF exposure requirements, and should be avoided.
Name and content of toxic and harmful substances
contained in this product are shown in the following
table
Toxic and harmful substances and elements
Name of parts （Pb）(Hg) (Cd) (Cr(VII) (PBB) (PBDE)
Circuit board
Shell
:It indicates that the content of toxic and harmful substances in all
homogeneous materials
of this part is
below
the
limit
specified in
SJ/T11363-2006.
:It indicates that the content of toxic and harmful substances is higher than
the
limit
specified in SJ/T11363-2006 in at least one
homogeneous
material
of this
part; however,
the the
reason why
the toxic
substance
of
that
part
exceeds the limit is that there is no applicable material to replace it currently.
For products that have reached or passed the service years for environmental
protection, they should be recycled
according to Measures for Control and Management of Electronic Information
Products and should not be thrown
away at will.
Manufacture
Shanghai Sunmi Technology Co.,
Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
S00030820770
USER
GUIDE
T7821
External
Product
Introduction
Camera
Battery
Instructions/Points
for
Attention
This device chooses 3.8V/3000mAh non-removable
built-in
lithium battery. Please don’t disassemble it by yourself.
To ensure the lifetime of this battery, please don’t charge
it
Minimalist
Setting
It will take only a few steps to enable an intelligent commercial device
①
2G/3G/4G
device. Insert the corresponding
2G/3G/4G
card in
shutdown mode, and then turn the device on.
Technical Indexes of the
Product
Items
Technical
Specification
Operating
after it has been completely
consumed.
(Please read
the
technical specification table
as for the
details
of card
support) system
CPU basic
Android
7.1
Volume
key
Power
key
micro
SIM
SIM card
slot
② Long press the power key for 2 to 3 seconds, light the screen, enter
the first boot
interface
and
then operate according
to the prompt.
As
for
this device, there
are two
types
of
Internet surfing
modes
available.
③
WIFI
setting
frequency 1.4GHz quad core
RAM 1GB LPDDR3
FLASH 8GB Nand Flash
Display screen 5
inch IPS, resolution
1280ⅹ720
Touch screen Capacitive touch control screen
·Click
“Setting”
button,
and
then
enable
WLAN
to
enter
WLAN
search
interface. Wait for its search and listing of availableWLAN hot spots;
·Click WLAN to be connected. If one encrypted network is selected, it is
necessary to enter access password for connection.
Camera 30W FF
2G：B2/B3/B5/B8
Menu
key
Main screen
key
How to download/use App
Wireless data 3G：WCDMA(B1/B2/B4/B5);EVDO(BC0/BC1)
4G：B2/B4/B7/B17/B28
Return key
Power key
Short press: light the screen, lock the screen.
Type-C USB
Speaker
Battery
cover
Charger
adapter
Charging
socket
As for the relevant Apps, you may complete the installation by opening
App market, browsing & downloading App in networking mode.
Common
troubleshooting
Unable to turn on the device (for example: too low electric
Wi
-
Fi
Built-in
IEEE802.11
a/b/g/n (2.4G/5G)
Bluetooth Supports Bluetooth
3.0/4.2
BLE supports iBeacon
Button Power key, volume key
Port USB Type
Cport
Battery
3.8V/3000mAh
dimension L 144.4mm ×W
73.2mm
×H 13.7mm
Long press: in shutdown mode, long press for 2 to 3 seconds
to turn on the device;
in service mode, long press for 2 to 3 seconds, and you can
choose to shut down or to reboot;
in crashed mode, long press for 11 seconds to automatically
reboot.
Volume key
Adjust the volume
Return key
Click to return to the previous screen
Main screen key
Click to quickly return to the main screen
Menu key
Click to quickly check the program running at the backstage;
choose application and sideslip to close this application.
Camera
Used for payment code scanning, supporting 1 D & QR code.
SIM card
slot
Note: this slot uses micro-SIM card;
when inserting or taking out SIM card, the device must
be always in shutdown mode. If it is inserted or taken
out in the state of power-on, it may cause device fault.
Open the battery cover, insert or take out SIM card in the
direction
as
shown
in
this
figure;
Charging base
(This base is optional)
Charging & battery
instructions
This device supports the charging with USB line, and also
charging with charging base;
Insert the base adapter into the charging socket;
Place the device into the charging base in the direction as
shown
in
this figure;
It is being charged, there will be a corresponding icon to display
it on the screen;
If there is no charging icon displayed, please check whether
the direction in which the device is placed into the charging
base is correct or not.
quantity of the device)
·Power on the device or place it onto the charging base
to
charge it. Turn the device on
after charging for 3 minutes;
·Check whether charging state is normally displayed or not on
the screen.
What to do if the device is crashed
Long press the power key for 11 seconds, and enter the
reboot state.
More using help
After turning on the device, please check the “User Guide”
of
the application
Adapter OUTPUT：DC5V/1A
INPUT：AC100~240V/0.15A
Package
Content
One host
One piece of User Guide
One charging adapter
One
USB
connection line
External
Product
Introduction
Camera
Battery
Instructions/Points
for
Attention
This device chooses 3.8V/3000mAh non-removable
built-in
lithium battery. Please don’t disassemble it by yourself.
To ensure the lifetime of this battery, please don’t charge
it
Minimalist
Setting
It will take only a few steps to enable an intelligent commercial device
①
2G/3G/4G
device. Insert the corresponding
2G/3G/4G
card in
shutdown mode, and then turn the device on.
Technical Indexes of the
Product
Items
Technical
Specification
Operating
after it has been completely
consumed.
(Please read
the
technical specification table
as for the
details
of card
support) system
CPU basic
Android
7.1
Volume
key
Power
key
micro
SIM
SIM card
slot
② Long press the power key for 2 to 3 seconds, light the screen, enter
the first boot
interface
and
then operate according
to the prompt.
As
for
this device, there
are two
types
of
Internet surfing
modes
available.
③
WIFI
setting
frequency 1.4GHz quad core
RAM 1GB LPDDR3
FLASH 8GB Nand Flash
Display screen 5
inch IPS, resolution
1280ⅹ720
Touch screen Capacitive touch control screen
·Click
“Setting”
button,
and
then
enable
WLAN
to
enter
WLAN
search
interface. Wait for its search and listing of availableWLAN hot spots;
·Click WLAN to be connected. If one encrypted network is selected, it is
necessary to enter access password for connection.
Camera 30W FF
2G：B2/B3/B5/B8
Menu
key
Main screen
key
How to download/use App
Wireless data 3G：WCDMA(B1/B2/B4/B5);EVDO(BC0/BC1)
4G：B2/B4/B7/B17/B28
Return key
Power key
Short press: light the screen, lock the screen.
Type-C USB
Speaker
Battery
cover
Charger
adapter
Charging
socket
As for the relevant Apps, you may complete the installation by opening
App market, browsing & downloading App in networking mode.
Common
troubleshooting
Unable to turn on the device (for example: too low electric
Wi
-
Fi
Built-in
IEEE802.11
a/b/g/n (2.4G/5G)
Bluetooth Supports Bluetooth
3.0/4.2
BLE supports iBeacon
Button Power key, volume key
Port USB Type
Cport
Battery
3.8V/3000mAh
dimension L 144.4mm ×W
73.2mm
×H 13.7mm
Long press: in shutdown mode, long press for 2 to 3 seconds
to turn on the device;
in service mode, long press for 2 to 3 seconds, and you can
choose to shut down or to reboot;
in crashed mode, long press for 11 seconds to automatically
reboot.
Volume key
Adjust the volume
Return key
Click to return to the previous screen
Main screen key
Click to quickly return to the main screen
Menu key
Click to quickly check the program running at the backstage;
choose application and sideslip to close this application.
Camera
Used for payment code scanning, supporting 1 D & QR code.
SIM card
slot
Note: this slot uses micro-SIM card;
when inserting or taking out SIM card, the device must
be always in shutdown mode. If it is inserted or taken
out in the state of power-on, it may cause device fault.
Open the battery cover, insert or take out SIM card in the
direction
as
shown
in
this
figure;
Charging base
(This base is optional)
Charging & battery
instructions
This device supports the charging with USB line, and also
charging with charging base;
Insert the base adapter into the charging socket;
Place the device into the charging base in the direction as
shown
in
this figure;
It is being charged, there will be a corresponding icon to display
it on the screen;
If there is no charging icon displayed, please check whether
the direction in which the device is placed into the charging
base is correct or not.
quantity of the device)
·Power on the device or place it onto the charging base
to
charge it. Turn the device on
after charging for 3 minutes;
·Check whether charging state is normally displayed or not on
the screen.
What to do if the device is crashed
Long press the power key for 11 seconds, and enter the
reboot state.
More using help
After turning on the device, please check the “User Guide”
of
the application
Adapter OUTPUT：DC5V/1A
INPUT：AC100~240V/0.15A
Package
Content
One host
One piece of User Guide
One charging adapter
One
USB
connection line
External
Product
Introduction
Camera
Battery
Instructions/Points
for
Attention
This device chooses 3.8V/3000mAh non-removable
built-in
lithium battery. Please don’t disassemble it by yourself.
To ensure the lifetime of this battery, please don’t charge
it
Minimalist
Setting
It will take only a few steps to enable an intelligent commercial device
①
2G/3G/4G
device. Insert the corresponding
2G/3G/4G
card in
shutdown mode, and then turn the device on.
Technical Indexes of the
Product
Items
Technical
Specification
Operating
after it has been completely
consumed.
(Please read
the
technical specification table
as for the
details
of card
support) system
CPU basic
Android
7.1
Volume
key
Power
key
micro
SIM
SIM card
slot
② Long press the power key for 2 to 3 seconds, light the screen, enter
the first boot
interface
and
then operate according
to the prompt.
As
for
this device, there
are two
types
of
Internet surfing
modes
available.
③
WIFI
setting
frequency 1.4GHz quad core
RAM 1GB LPDDR3
FLASH 8GB Nand Flash
Display screen 5
inch IPS, resolution
1280ⅹ720
Touch screen Capacitive touch control screen
·Click
“Setting”
button,
and
then
enable
WLAN
to
enter
WLAN
search
interface. Wait for its search and listing of availableWLAN hot spots;
·Click WLAN to be connected. If one encrypted network is selected, it is
necessary to enter access password for connection.
Camera 30W FF
2G：B2/B3/B5/B8
Menu
key
Main screen
key
How to download/use App
Wireless data 3G：WCDMA(B1/B2/B4/B5);EVDO(BC0/BC1)
4G：B2/B4/B7/B17/B28
Return key
Power key
Short press: light the screen, lock the screen.
Type-C USB
Speaker
Battery
cover
Charger
adapter
Charging
socket
As for the relevant Apps, you may complete the installation by opening
App market, browsing & downloading App in networking mode.
Common
troubleshooting
Unable to turn on the device (for example: too low electric
Wi
-
Fi
Built-in
IEEE802.11
a/b/g/n (2.4G/5G)
Bluetooth Supports Bluetooth
3.0/4.2
BLE supports iBeacon
Button Power key, volume key
Port USB Type
Cport
Battery
3.8V/3000mAh
dimension L 144.4mm ×W
73.2mm
×H 13.7mm
Long press: in shutdown mode, long press for 2 to 3 seconds
to turn on the device;
in service mode, long press for 2 to 3 seconds, and you can
choose to shut down or to reboot;
in crashed mode, long press for 11 seconds to automatically
reboot.
Volume key
Adjust the volume
Return key
Click to return to the previous screen
Main screen key
Click to quickly return to the main screen
Menu key
Click to quickly check the program running at the backstage;
choose application and sideslip to close this application.
Camera
Used for payment code scanning, supporting 1 D & QR code.
SIM card
slot
Note: this slot uses micro-SIM card;
when inserting or taking out SIM card, the device must
be always in shutdown mode. If it is inserted or taken
out in the state of power-on, it may cause device fault.
Open the battery cover, insert or take out SIM card in the
direction
as
shown
in
this
figure;
Charging base
(This base is optional)
Charging & battery
instructions
This device supports the charging with USB line, and also
charging with charging base;
Insert the base adapter into the charging socket;
Place the device into the charging base in the direction as
shown
in
this figure;
It is being charged, there will be a corresponding icon to display
it on the screen;
If there is no charging icon displayed, please check whether
the direction in which the device is placed into the charging
base is correct or not.
quantity of the device)
·Power on the device or place it onto the charging base
to
charge it. Turn the device on
after charging for 3 minutes;
·Check whether charging state is normally displayed or not on
the screen.
What to do if the device is crashed
Long press the power key for 11 seconds, and enter the
reboot state.
More using help
After turning on the device, please check the “User Guide”
of
the application
Adapter OUTPUT：DC5V/1A
INPUT：AC100~240V/0.15A
Package
Content
One host
One piece of User Guide
One charging adapter
One
USB
connection line
External
Product
Introduction
Camera
Battery
Instructions/Points
for
Attention
This device chooses 3.8V/3000mAh non-removable
built-in
lithium battery. Please don’t disassemble it by yourself.
To ensure the lifetime of this battery, please don’t charge
it
Minimalist
Setting
It will take only a few steps to enable an intelligent commercial device
①
2G/3G/4G
device. Insert the corresponding
2G/3G/4G
card in
shutdown mode, and then turn the device on.
Technical Indexes of the
Product
Items
Technical
Specification
Operating
after it has been completely
consumed.
(Please read
the
technical specification table
as for the
details
of card
support) system
CPU basic
Android
7.1
Volume
key
Power
key
micro
SIM
SIM card
slot
② Long press the power key for 2 to 3 seconds, light the screen, enter
the first boot
interface
and
then operate according
to the prompt.
As
for
this device, there
are two
types
of
Internet surfing
modes
available.
③
WIFI
setting
frequency 1.4GHz quad core
RAM 1GB LPDDR3
FLASH 8GB Nand Flash
Display screen 5
inch IPS, resolution
1280ⅹ720
Touch screen Capacitive touch control screen
·Click
“Setting”
button,
and
then
enable
WLAN
to
enter
WLAN
search
interface. Wait for its search and listing of available WLAN hot spots;
·Click WLAN to be connected. If one encrypted network is selected, it is
necessary to enter access password for connection.
Camera 30W FF
2G：B2/B3/B5/B8
Menu
key
Main screen
key
How to download/use App
Wireless data 3G：WCDMA(B1/B2/B4/B5);EVDO(BC0/BC1)
4G：B2/B4/B7/B17/B28
Return key
Power key
Short press: light the screen, lock the screen.
Type-C USB
Speaker
Battery
cover
Charger
adapter
Charging
socket
As for the relevant Apps, you may complete the installation by opening
App market, browsing & downloading App in networking mode.
Common
troubleshooting
Unable to turn on the device (for example: too low electric
Wi
-
Fi
Built-in
IEEE802.11
a/b/g/n (2.4G/5G)
Bluetooth Supports Bluetooth
3.0/4.2
BLE supports iBeacon
Button Power key, volume key
Port USB Type
Cport
Battery
3.8V/3000mAh
dimension L 144.4mm ×W
73.2mm
×H 13.7mm
Long press: in shutdown mode, long press for 2 to 3 seconds
to turn on the device;
in service mode, long press for 2 to 3 seconds, and you can
choose to shut down or to reboot;
in crashed mode, long press for 11 seconds to automatically
reboot.
Volume key
Adjust the volume
Return key
Click to return to the previous screen
Main screen key
Click to quickly return to the main screen
Menu key
Click to quickly check the program running at the backstage;
choose application and sideslip to close this application.
Camera
Used for payment code scanning, supporting 1 D & QR code.
SIM card
slot
Note: this slot uses micro-SIM card;
when inserting or taking out SIM card, the device must
be always in shutdown mode. If it is inserted or taken
out in the state of power-on, it may cause device fault.
Open the battery cover, insert or take out SIM card in the
direction
as
shown
in
this
figure;
Charging base
(This base is optional)
Charging & battery
instructions
This device supports the charging with USB line, and also
charging with charging base;
Insert the base adapter into the charging socket;
Place the device into the charging base in the direction as
shown
in
this figure;
It is being charged, there will be a corresponding icon to display
it on the screen;
If there is no charging icon displayed, please check whether
the direction in which the device is placed into the charging
base is correct or not.
quantity of the device)
·Power on the device or place it onto the charging base
to
charge it. Turn the device on
after charging for 3 minutes;
·Check whether charging state is normally displayed or not on
the screen.
What to do if the device is crashed
Long press the power key for 11 seconds, and enter the
reboot state.
More using help
After turning on the device, please check the “User Guide”
of
the application
Adapter OUTPUT：DC5V/1A
INPUT：AC100~240V/0.15A
Package
Content
One host
One piece of User Guide
One charging adapter
One
USB
connection line
External
Product
Introduction
Camera
Battery
Instructions/Points
for
Attention
This device chooses 3.8V/3000mAh non-removable
built-in
lithium battery. Please don’t disassemble it by yourself.
To ensure the lifetime of this battery, please don’t charge
it
Minimalist
Setting
It will take only a few steps to enable an intelligent commercial device
①
2G/3G/4G
device. Insert the corresponding
2G/3G/4G
card in
shutdown mode, and then turn the device on.
Technical Indexes of the
Product
Items
Technical
Specification
Operating
after it has been completely
consumed.
(Please read
the
technical specification table
as for the
details
of card
support) system
CPU basic
Android
7.1
Volume
key
Power
key
micro
SIM
SIM card
slot
② Long press the power key for 2 to 3 seconds, light the screen, enter
the first boot
interface
and
then operate according
to the prompt.
As
for
this device, there
are two
types
of
Internet surfing
modes
available.
③
WIFI
setting
frequency 1.4GHz quad core
RAM 1GB LPDDR3
FLASH 8GB Nand Flash
Display screen 5
inch IPS, resolution
1280ⅹ720
Touch screen Capacitive touch control screen
·Click
“Setting”
button,
and
then
enable
WLAN
to
enter
WLAN
search
interface. Wait for its search and listing of available WLAN hot spots;
·Click WLAN to be connected. If one encrypted network is selected, it is
necessary to enter access password for connection.
Camera 30W FF
2G：B2/B3/B5/B8
Menu
key
Main screen
key
How to download/use App
Wireless data 3G：WCDMA(B1/B2/B4/B5);EVDO(BC0/BC1)
4G：B2/B4/B7/B17/B28
Return key
Power key
Short press: light the screen, lock the screen.
Type-C USB
Speaker
Battery
cover
Charger
adapter
Charging
socket
As for the relevant Apps, you may complete the installation by opening
App market, browsing & downloading App in networking mode.
Common
troubleshooting
Unable to turn on the device (for example: too low electric
Wi
-
Fi
Built-in
IEEE802.11
a/b/g/n (2.4G/5G)
Bluetooth Supports Bluetooth
3.0/4.2
BLE supports iBeacon
Button Power key, volume key
Port USB Type
Cport
Battery
3.8V/3000mAh
dimension L 144.4mm ×W
73.2mm
×H 13.7mm
Long press: in shutdown mode, long press for 2 to 3 seconds
to turn on the device;
in service mode, long press for 2 to 3 seconds, and you can
choose to shut down or to reboot;
in crashed mode, long press for 11 seconds to automatically
reboot.
Volume key
Adjust the volume
Return key
Click to return to the previous screen
Main screen key
Click to quickly return to the main screen
Menu key
Click to quickly check the program running at the backstage;
choose application and sideslip to close this application.
Camera
Used for payment code scanning, supporting 1 D & QR code.
SIM card
slot
Note: this slot uses micro-SIM card;
when inserting or taking out SIM card, the device must
be always in shutdown mode. If it is inserted or taken
out in the state of power-on, it may cause device fault.
Open the battery cover, insert or take out SIM card in the
direction
as
shown
in
this
figure;
Charging base
(This base is optional)
Charging & battery
instructions
This device supports the charging with USB line, and also
charging with charging base;
Insert the base adapter into the charging socket;
Place the device into the charging base in the direction as
shown
in
this figure;
It is being charged, there will be a corresponding icon to display
it on the screen;
If there is no charging icon displayed, please check whether
the direction in which the device is placed into the charging
base is correct or not.
quantity of the device)
·Power on the device or place it onto the charging base
to
charge it. Turn the device on
after charging for 3 minutes;
·Check whether charging state is normally displayed or not on
the screen.
What to do if the device is crashed
Long press the power key for 11 seconds, and enter the
reboot state.
More using help
After turning on the device, please check the “User Guide”
of
the application
Adapter OUTPUT：DC5V/1A
INPUT：AC100~240V/0.15A
Package
Content
One host
One piece of User Guide
One charging adapter
One
USB
connection line
This device complies with Part 15 of the FCC Rules. Operation
is
subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: 2AH25M2
NOTE: Changes
or
modifications
not
expressly approved by the
party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if
not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which
can be
determined by turning the equipment
off and
on, the user is encouraged to try to correct the interference by one
or
more of the following measures:
---Reorient
or relocate the receiving antenna.
---Increase
the separation between the equipment and receiver.
---Connect
the equipment into
an
outlet
on a circuit
different
from
that to which the receiver is connected.
---Consult
the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
With RF exposure requirements, a minimum separation distance
of
1.0cm must be maintained between the user’s body and the handset,
including the antenna.
Third-party belt-clips,
holsters, and similar including the antenna.
Third-party belt-clips,
holsters, and similar accessories used by
this
device should not contain any metallic components.
Body-worn
accessories that do not meet these requirements may not comply
with
RF exposure requirements and should be
avoided
.
Specific Absorption Rate
(SAR)
information:
This wireless phone meets the government's requirements for exposure
to radio waves. The guidelines are based on standards that were
developed by independent
scientific
organizations through periodic
and
thorough evaluation
of scientific
studies. The standards include
a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
FCC RF Exposure Information and Statement. The SAR limit of USA
(FCC) is 1.6W/kg averaged over one gram of tissue.
Device types:
T8900&T8901
has also been tested against this SAR
limit. The highest SAR value reported under this standard during
product
certification when properly worn
on
the body
is
1.363W/kg
(1gSAR，
test
distance：5mm，limit 1.6W/kg).
This
device was tested
for
body-
worn operations with the back of the handset kept 5mm from the body.
To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 5mm separation distance between the
user's body and the back of the handset. The use of belt clips, holsters
and similar accessories should not contain metallic components in its
assembly. The use
of
accessories that do not satisfy these requirements may not comply
with
FCC RF exposure requirements, and should be avoided.
Name and content of toxic and harmful substances
contained in this product are shown in the following
table
Toxic and harmful substances and elements
Name of parts （Pb）(Hg) (Cd) (Cr(VII) (PBB) (PBDE)
Circuit board
Shell
:It indicates that the content of toxic and harmful substances in all
homogeneous materials
of this part is
below
the
limit
specified in
SJ/T11363-2006.
:It indicates that the content of toxic and harmful substances is higher than
the
limit
specified in SJ/T11363-2006 in at least one
homogeneous
material
of this
part; however,
the the
reason why
the toxic
substance
of
that
part
exceeds the limit is that there is no applicable material to replace it currently.
For products that have reached or passed the service years for environmental
protection, they should be recycled
according to Measures for Control and Management of Electronic Information
Products and should not be thrown
away at will.
Manufacture
Shanghai Sunmi Technology Co.,
Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
S00030820770
USER
GUIDE
T7821
This device complies with Part 15 of the FCC Rules. Operation
is
subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: 2AH25M2
NOTE: Changes
or
modifications
not
expressly approved by the
party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if
not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which
can be
determined by turning the equipment
off and
on, the user is encouraged to try to correct the interference by one
or
more of the following measures:
---Reorient
or relocate the receiving antenna.
---Increase
the separation between the equipment and receiver.
---Connect
the equipment into
an
outlet
on a circuit
different
from
that to which the receiver is connected.
---Consult
the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
With RF exposure requirements, a minimum separation distance
of
1.0cm must be maintained between the user’s body and the handset,
including the antenna.
Third-party belt-clips,
holsters, and similar including the antenna.
Third-party belt-clips,
holsters, and similar accessories used by
this
device should not contain any metallic components.
Body-worn
accessories that do not meet these requirements may not comply
with
RF exposure requirements and should be
avoided
.
Specific Absorption Rate
(SAR)
information:
This wireless phone meets the government's requirements for exposure
to radio waves. The guidelines are based on standards that were
developed by independent
scientific
organizations through periodic
and
thorough evaluation
of scientific
studies. The standards include
a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
FCC RF Exposure Information and Statement. The SARlimit of USA
(FCC) is 1.6W/kg averaged over one gram of tissue.
Device types:
T8900&T8901
has also been tested against this SAR
limit. The highest SAR value reported under this standard during
product
certification when properly worn
on
the body
is
1.363W/kg
(1gSAR，
test
distance：5mm，limit 1.6W/kg).
This
device was tested
for
body-
worn operations with the back of the handset kept 5mm from the body.
To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 5mm separation distance between the
user's body and the back of the handset. The use of belt clips, holsters
and similar accessories should not contain metallic components in its
assembly. The use
of
accessories that do not satisfy these requirements may not comply
with
FCC RF exposure requirements, and should be avoided.
Name and content of toxic and harmful substances
contained in this product are shown in the following
table
Toxic and harmful substances and elements
Name of parts （Pb）(Hg) (Cd) (Cr(VII) (PBB) (PBDE)
Circuit board
Shell
:It indicates that the content of toxic and harmful substances in all
homogeneous materials
of this part is
below
the
limit
specified in
SJ/T11363-2006.
:It indicates that the content of toxic and harmful substances is higher than
the
limit
specified in SJ/T11363-2006 in at least one
homogeneous
material
of this
part; however,
the the
reason why
the toxic
substance
of
that
part
exceeds the limit is that there is no applicable material to replace it currently.
For products that have reached or passed the service years for environmental
protection, they should be recycled
according to Measures for Control and Management of Electronic Information
Products and should not be thrown
away at will.
Manufacture
Shanghai Sunmi Technology Co.,
Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
S00030820770
USER
GUIDE
T7821
This device complies with Part 15 of the FCC Rules. Operation
is
subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: 2AH25M2
NOTE: Changes
or
modifications
not
expressly approved by the
party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if
not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which
can be
determined by turning the equipment
off and
on, the user is encouraged to try to correct the interference by one
or
more of the following measures:
---Reorient
or relocate the receiving antenna.
---Increase
the separation between the equipment and receiver.
---Connect
the equipment into
an
outlet
on a circuit
different
from
that to which the receiver is connected.
---Consult
the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
With RF exposure requirements, a minimum separation distance
of
1.0cm must be maintained between the user’s body and the handset,
including the antenna.
Third-party belt-clips,
holsters, and similar including the antenna.
Third-party belt-clips,
holsters, and similar accessories used by
this
device should not contain any metallic components.
Body-worn
accessories that do not meet these requirements may not comply
with
RF exposure requirements and should be
avoided
.
Specific Absorption Rate
(SAR)
information:
This wireless phone meets the government's requirements for exposure
to radio waves. The guidelines are based on standards that were
developed by independent
scientific
organizations through periodic
and
thorough evaluation
of scientific
studies. The standards include
a
substantial safety margin designed to assure the safety of all persons
regardless of age or health.
FCC RF Exposure Information and Statement. The SARlimit of USA
(FCC) is 1.6W/kg averaged over one gram of tissue.
Device types:
T8900&T8901
has also been tested against this SAR
limit. The highest SARvalue reported under this standard during
product
certification when properly worn
on
the body
is
1.363W/kg
(1gSAR，
test
distance：5mm，limit 1.6W/kg).
This
device was tested
for
body-
worn operations with the back of the handset kept 5mm from the body.
To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 5mm separation distance between the
user's body and the back of the handset. The use of belt clips, holsters
and similar accessories should not contain metallic components in its
assembly. The use
of
accessories that do not satisfy these requirements may not comply
with
FCC RF exposure requirements, and should be avoided.
Name and content of toxic and harmful substances
contained in this product are shown in the following
table
Toxic and harmful substances and elements
Name of parts （Pb）(Hg) (Cd) (Cr(VII) (PBB) (PBDE)
Circuit board
Shell
:It indicates that the content of toxic and harmful substances in all
homogeneous materials
of this part is
below
the
limit
specified in
SJ/T11363-2006.
:It indicates that the content of toxic and harmful substances is higher than
the
limit
specified in SJ/T11363-2006 in at least one
homogeneous
material
of this
part; however,
the the
reason why
the toxic
substance
of
that
part
exceeds the limit is that there is no applicable material to replace it currently.
For products that have reached or passed the service years for environmental
protection, they should be recycled
according to Measures for Control and Management of Electronic Information
Products and should not be thrown
away at will.
Manufacture
Shanghai Sunmi Technology Co.,
Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
S00030820770
USER
GUIDE
T7821
Table of contents
