SureShot 513 ST. LOUIS User manual

SURE SHOT
PORTABLE COURT SYSTEM
MODEL 513 ST. LOUIS
ASSEMBLY INSTRUCTIONS
FAILURE TO READ INSTRUCTIONS COMPLETELY BEFORE
ASSEMBLY COULD RESULT IN SERIOUS INJURY !!!
BEFORE BEGINNING ASSEMBLY READ INSTRUCTIONS
COMPLETELYAND CHECK TO SEE IF ALL PARTS WERE
INCLUDED USING THE PARTS LIST PROVIDED.
WARNING !!!
TO PREVENT THE PORTABLE COURT
SYSTEM FROM TIPPING. DO NOTATTEMPT
TO STAND THE UNIT UP WITHOUT FIRST
FILLING THE BASE WITH SAND.
THE UNIT COULD FALL OVER WITHOUT SAND
IN THE BASE THIS COULD CAUSE DAMAGE
OR INJURY
DO NOT ALLOW CHILDREN TO ADJUST.
CLIMB ON OR HANG FROM ANY PART
OF UNIT.
DO NOT PERFORM SLAM - DUNK PLAY
ON THIS UNIT
THE PORTABLE UNITS ARE NOT DESIGNED
FOR THIS TYPE OF EXTREME USE.
DO NOT USE THE UNIT DURING WINDY
CONDITIONS
YOUR BEST SHOT !

P1 P2 P3
PART LIST
Tension Bar
Steel Strip with
two holes
45×35mm
Qty. - 2 Nos.
45×8mm
110×8mm
50×8mm
38×8mm
50×8mm
110×8mm
153×10mm
44×12mm
Round 30×12mm Round Plastic Caps for Nut Pipe Top Cap
Ground Anchor
125×8mm
Ground Anchor Sleeve
A B C D E F G
IJKM
N
O
153×10mm
H
L
P
P4
P5 P6 P7 P8
Steel Strip with
one hole 45×35mm
Qty.- 4 Nos.
Page-2

POLE INSTRUCTIONS
BE SURE TO CORRECTLY IDENTIFY THE POLE SECTIONS
BEFORE BEGINNING ASSEMBLY
TOP POLE SECTION
FOUR ROUND HOLES MID POLE SECTION NO HOLES BOTTOM POLE TWO ROUND HOLES
AT THE BOTTOM
AND TWO ROUND
HOLE AT THE MID
POINT
NOTE : ALL POLES HAVE A SMALL HOLE AT THE TOPTHIS IS FOR
MANUFACTURING PURPOSES ONLY.
Page-3

Required Material and tools
1. 8×25kg sand bags
2. Adjustable wrench
3. Hammer
NOTE : Bolt kit check list is included in the bolt kit. Be sure to check contents
prior to assembly. (Two men required for assembly )
Insert the rod through wheels and bottom pole holes with base (P1).
Attach support tubes P7
at the both side the base
(P1) using nut &
bolt A-45×8mm & use
two holes strip (M) as a
washer under the base
STEP-2
Attach other side of tube (P7)
with lower pole using nut & bolt
(E-110×8mm) & tighten it with
the help of two spanners
STEP-3
4. 13mm Wrench/socket
5. Large screwdriver
6. 2 block wood approx. 10×10×3cm
Fill the base (P1) with water or sand
STEP-4
Warning
This unit can hold 120 Liters of water instead
of sand. In case of using water make sure that
base P1 is close properly with ring gasket inside
the cap. In case of using water strongly advice to
control the tightness of the base every time you
are going to play.
STEP-1
OR
STEP-1
Page-4

STEP-6 Attach top pole with middle pole to attach with lower pole
which is attach to base (P1) using block wood & hammer
STEP-7 Attach small extension tubes (P5) with top pole using nut & bolt
(H-153×10mm) in tighten it with the help of two spanners.
Attach ring (P2) with backboard (P3) at the same time attach back
support (P4) using nut & bolt (B-50×8mm) and at the top of
backboard support use nut & bolt (C-38×8mm).
STEP-5
STEP-8
Attach big tubes P5 with top pole second hole using
nut & bolt (H-153×10mm) in tighten it with the help of two spanners.
extension ( )
Page-5
BEFORE CONTINUING ASSEMBLY
Backboard and goal should be assembled at ground level.
Assembly at top of pole could result in injury.

Attach small & big extension
tubes (P5) with backboard (P3)
back support (P4) using nut &
bolt (G-153×10mm) and tighten
it with the help of two spanners.
STEP-9
Round tube (I-44×12mm)
between
back support (P4)
Insert internal tube pipe to the tension bar (P8). Make sure that
the spring rod hole match to hole of extension bar pipe (P8).
STEP-10
Attach top side of tension bar (P8) with big extension tube (P5)
using nut & bolt (F-110×8mm).
STEP-11
Round tube (J)
between
extension
tube
(P5- 30×12mm)
& tension
bar (P8)
STEP-12
Attach bottom side
of tension bar (P8)
with middle pole
clip using nut &
bolt (D- 50×8 mm)
and tighten it
with the help of two spanners.
Page-6

Cover the top
pole with plastic
cap (L ) & also
cover the nut
with plastic
cap (K) before
pole is in playing
potion
Use the large loops of the
net install onto the ring
"no-ties"
Locate the unit at desired playing location.
Start the installation of the ground anchor
(O-125×8mm) by hand approximately 8cm
behind unit. Finish installing the anchor by
inserting large screw driver into the eye
of the anchor and twisting until only the eye is
remaining above ground.
Ground anchor
sleeve (P)
Steel Strip (N)
45×34mm
Part (O)
Part (O)
FOR ADDITIONAL STABILITY
Page-7
STEP-13
STEP-14

POLE MAINTENANCE
Periodically wipe down pole with a damp cloth to remove dirt, pesticides,
herbicides, etc. This routing will prolong the life of your pole.
If your pole becomes scratched and rust begins to appear, repair by using rust
proof gloss black paint ( follow instructions on paint can).
THANK YOU FOR BUYING SURE SHOT !!!
Page-8
STEP-15
To adjust the height of the goal You will slide tension bar in an out
the tension bar locks in three positions, setting the goal height
at 245cm, 275cm and at the official height for a adults of 305cm.
To change the height of the goal, firmly grip the tension bar handle
with one hand while you pull the plastic ball- lock out. Slide the tension
bar up and down and release the plastic ball-lock to find the locking
position.