Swann Chesapeake Series User manual

Cabinet Mount Vanity Tops & Bowls
mProduct Warnings
mSafety Guidelines
mKit Contents
mRequired Tools
mPreparation Tips
mInstallation Procedure
mCleaning & Maintenance
mSurface Repair
mWarranty Information
Read and Understand
Before Installing
Form #255-05-16
Models:
Chesapeake Vanity (Single Bowl)
Chesapeake Vanity (Double Bowl)
Contour Vanity (Single Bowl)
Ellipse Vanity (Single Bowl)
Ellipse Vanity (Double Bowl)
Europa Vanity (Single Bowl)
swanstone.com

IMPORTANT NOTICE: Indicates that equipment or property
damage can result if instructions are not followed.
Read and Understand the Manual
It is the responsibility of any individual who installs or
maintains this product to fully understand and follow
proper installation and maintenance procedures. Be aware
of the inherent dangers in the use of power tools when
installing this product. Read and understand all Warnings,
Cautions, and Important Notices in this manual.
Work Safely
DO NOT proceed if any doubt arises about the correct
or safe method of performing anything found in this
or other Swanstone manuals. The installation of this product
can require using power tools. Do not use power tools without
adequate training. If necessary, hire or consult a trained
professional for expert assistance before continuing.
Use Proper Tools
Always use proper tools which are in good, working
condition during the installation of the Swanstone
products. Using tools other than those listed could adversely
affect the integrity of floors, pipes, walls, or this product and
could result in water damage or other damage to floors, pipes,
walls, or other portions of your building or home.
Inspect Before Cutting
Make sure no electrical wiring or plumbing is present
before cutting into any surface.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in injury. It may also be
used to alert against unsafe practices.
Use Proper Installation Methods
Follow all instructions related to vanity tops and bowls
preparation. Failure to follow these instructions could
result in water damage.
Slipping Hazard
Do not install this product in the presence of water.
Installing this product without drying all surfaces, or in
the presence of water, could cause you to slip and fall due to
wet floors or spilled fluids. Personal injury can result from slips
or falls. Before installation, dry all surfaces, including the floor,
with a cloth or paper towel. Clean up all water or spilled fluids
immediately.
Tripping Hazard
Personal injury can result from tripping over power
cords, tools, or other items. DO NOT leave items laying
around the work area.
CAUTION
IMPORTANT NOTICE
The Swan Assurance — if our product is
properly installed and maintained, as stated in
these instructions, it will not leak.
Remember –
Safety First
The Swan Corporation, the makers of the
Swan products, cannot anticipate every
possible circumstance that might involve
a potential hazard during the installation
of our product(s). The warnings and
instructions in this installation guide
are, therefore, not all-inclusive. If a tool,
installation procedure, or work method
that is not specifically recommended by
The Swan Corporation is used, you must
satisfy yourself that it is safe. You should
also make sure that the Swan product(s)
will not be damaged by the methods you
choose. The Swan Corporation will not be
held responsible for water damage of any
kind in connection with the installation of
one of our Swan drop-in vanity tops.
To avoid product damage, personal injury,
or even possible death, carefully read,
understand, and follow all the instructions
in this installation guide before installing
this product(s). Do not use cleaning
fluids or operate power tools unless you
read and understand the instructions
and warnings in this and all other
applicable labels or manuals. Proper use
of tools and the products described in
this guide is your responsibility.
WARRANTY
This product is covered by a Limited
Lifetime Warranty. Refer to the Warranty
section in this manual for complete details.
Save this manual for future
reference.
Important information on cleaning,
maintenance, and repair is contained
within.
IMPORTANT NOTICE
WARNING
Safety Guidelines

Personal Protection
Be sure to use all personal protective
equipment, such as sturdy work boots,
preferably with steel toes, gloves, and hard hat, if necessary,
to ensure your own safety. To prevent possible damage to
your hearing, always wear ear protection, such as earmuffs or
earplugs, when working around power tools.
Cutting Hazard
The installation of the Swanstone product may require
using power tools. Keep hands away from the cutting
edge of any tool used in the installation of our product. Placing
fingers in or around the cutting blades could result in serious
personal injury.
Sharp Edge Hazard
After cutting the edge of a Swanstone drop-in vanity
top, it can be sharp. Wear protective gloves to prevent
personal injury.
Room Temperature
Allow the Swanstone sink and silicone sealants
to adjust to room temperature for at least six
hours before installation. The product should not be installed at
temperatures below 65°F.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in serious injury or
death.
Eye Protection
Be sure to use all personal protective equipment to
ensure your own safety. To avoid eye injury, always
wear protective glasses with side shields when using power
tools. Also, make sure no one else can be injured by flying
particles when using power tools.
Fire Hazard
Personal injury or death can result from a
fire caused by flammable liquids or silicone sealants. Cleaners
or solvents can be highly explosive, resulting in personal
injury or even death, when not used properly. Clean up any
flammable substance immediately. Sparks or open flames can
cause flammable substances to ignite. DO NOT smoke while
working on or near any flammable substance.
Solvents Hazard
Follow all manufacturer’s safety instructions for silicone
sealants and denatured alcohol. Alcohol vapors are
both flammable and hazardous to breathe. Silicone vapors
may irritate eyes and nose. Personal injury can result from
improperly handling or use of products, such as denatured
alcohol. Always follow the manufacturer’s recommendations
for the safe use of these products. Ventilate any work area
before beginning to apply silicone sealants, cleaning agents, or
solvents.
Fumes Hazard
The fumes from the silicone and solvents used
by the installer can be harmful if used in an
unventilated room. Always work in a well-ventilated area. To
keep the area well-ventilated, open windows and use exhaust
fans. If adequate ventilation is not achievable or practical, use
respiratory protective equipment.
Dust Hazard
When cutting or drilling the Swanstone product,
use a dust collection method which prevents
dust particles from going into the air. Always work in a well-
ventilated area. Always use an OSHA approved dust mask
when cutting, drilling, or sanding Swanstone products.
Power Tool Hazard
To prevent personal injury or possible
death, always follow the electrical safety
recommendations of the power tool’s manufacturer. Do not
use power tools in an unsafe manner. Power tools should only
be connected to a circuit protected by a ground-fault circuit
interrupter (GFI).
Shock Hazard
Never use electric power tools around water,
condensation, or other liquids. Electric shock
can cause severe burns, significant injuries, and even death. If
an extension cord is required, always use an OSHA approved
extension cord. Power cords should only be connected to a
circuit protected by a ground-fault circuit interrupter (GFI).
Electrical Shock Hazard
Contacting live electrical wiring with power tools
or hand tools can cause serious injury or death.
Make sure all related circuit breakers are turned OFF. Test for
live circuits or wiring inside any wall where installation of the
Swanstone product requires cutting into a wall.
Electrocution Hazard
Water and other liquids conduct electric current
and can create a short circuit, resulting in
injury or death. Keep all liquids away from electrical cords
and power tools. DO NOT create a short circuit between a
source of electricity and a liquid by being in contact with both
simultaneously.
General Information
Required Tools
mDrill
mScrewdriver
mRuler/Tape Measure
mSafety Glasses
m1/4” Twist Drill and 1-3/8” Hole Saw (Carbide Tipped)
mSilicone
mCaulking Gun
mDust Mask
mDenatured Alcohol
mColor-Matched Silicone Sealant
mConstruction Adhesive (For Undermount Installation)
m3/4” Plywood Cut to 3” Strips (For Undermount Installation)
ADA Applications
These products meet the dimensional requirement to allow
for installation in ADA applications. For up-to-date ADA
regulations, visit www.ADA.gov.
WARNING
800-325-7008
Safety Guidelines

Sink Contents
Confirm that all parts for the vanity top or bowl have been
included before beginning installation.
Chesapeake Vanity (Single Bowl)
CH1B-2225 (22-1/2”D x 25”W)
CH1B-2231 (22-1/2”D x 31”W)
CH1B-2237 (22-1/2”D x 37”W)
CH1B-2243 (22-1/2”D x 43”W)
CH1B-2249 (22-1/2”D x 49”W)
CH1B-2255 (22-1/2”D x 55”W)
CH1B-2261 (22-1/2”D x 61”W)
Chesapeake Vanity (Double Bowl)
CH2B-2261 (22-1/2”D x 61”W)
CH2B-2273 (22-1/2”D x 73”W)
Contour Vanity (Single Bowl)
CV-2225 (22”D x 25”W)
CV-2231 (22”D x 31”W)
CV-2237 (22”D x 37”W)
CV-2243 (22”D x 43”W)
CV-2249 (22”D x 49”W)
Ellipse Vanity (Single Bowl)
VT1B-1719 (17”D x 19”W)
VT1B-1925 (19”D x 25”W)
VT1B-1931 (19”D x 31”W)
VT1B-1937 (19”D x 37”W)
VT1B-2225 (22”D x 25”W)
VT1B-2231 (22”D x 31”W)
VT1B-2237 (22”D x 37”W)
VT1B-2243 (22”D x 43”W)
VT1B-2249 (22”D x 49”W)
VT1B-2255 (22”D x 55”W)
VT1B-2261 (22”D x 61”W)
Ellipse Vanity (Double Bowl)
VT2B-2261 (22”D x 61”W)
EVDB-01
EVSB-01
CTVSB-01
CVDB-01
CVSB-01
Swan 4 800-325-7008
General Information

Europa Vanity (Single Bowl)
EV-2225 (22-1/2”D x 25”W)
EV-2231 (22-1/2”D x 31”W)
EV-2237 (22-1/2”D x 37”W)
EV-2243 (22-1/2”D x 43”W)
EV-2249 (22-1/2”D x 49”W)
EV-2255 (22-1/2”D x 55”W)
EV-2261 (22-1/2”D x 61”W)
Vanity Top Accessories
Side Splash and Front Apron Panels
Side Splash Panel for Vanity Tops (one per carton)
Model Part Dimensions
VT18-3SS VT01803SS 18” W x 3” H x 3/8”D
VT19-SS VT00019SS 19” W x 3” H x 3/4” D
VT21-3SS VT02103SS 21” W x 3” H x 3/8”D
VT22-SS VT00022SS 22” W x 3” H x 3/4” D
Side Splash Panel for Chesapeake (one per carton)
Model Part Dimensions
CHVTSS CHVTSS 21-5/8” W x 3-1/2” H x 3/4” D
Side Splash Panel for Europa (one per carton)
Model Part Dimensions
EVTSS EV00022SS 21-1/4” W x 3-1/2” H x 3/4” D
Front Apron Panel (one per carton)
Model Part Dimensions
VT37FA VT02237FA 37” W x 8” H x 1/2” D
VT55FA VT02255FA 55” W x 8” H x 1/2” D
VT1B2261FA VT02261FA 61” W x 8” H x 1/2” D
Side Apron Panel (one per carton)
Model Part Dimensions
VT22SA VT00022SA 21” x 8” x 1/2” D
Unpack Carton
mUse care when opening the box not to damage the sink.
mThis product is shipped to you or your retail center after
careful inspection. After purchasing the sink, carefully
unpack and inspect the product for any shipping damage
that may have occurred. If damage is found, report it
immediately to the store of purchase. After inspection and
during installation, protect the products from construction
damage, by moving them to another room or area until ready
to install.
mPlease use the model number located on the side of the
box, or the front of this manual, when contacting us with
questions concerning the installation of this unit.
mMake sure the sink is the correct size and in good condition.
Installation of damaged product will void the warranty.
Helpful Hints
mRead these instructions carefully and familiarize yourself
with the various parts of the sink.
mThe variety of installations possible for this sink may require
procedures other than those shown. Ensure construction is
correctly sized, plumb, and square.
mAllow sufficient time for the parts in this sink to adjust to
room temperature. We do not recommend installation of this
product at temperatures below 65 degrees.
mStore unused materials away from the work area to prevent
accidental damage.
mTurn off the hot and cold water supply before starting
installation.
Caulking Tips
mFollow the instructions on the caulking tube.
mWhen job is complete, inspect all caulked areas for gaps
and fill as needed.
mClean up excess silicone using denatured alcohol and a
clean cloth.
mBe very careful not to disturb caulk joints before they dry.
EUVSB-01
800-325-7008 5 Swan
General Information Installation Procedure

Installation Procedure
Disclaimer
mThe information contained in this Installation Manual is given
free of charge. It is based upon technical data which we
believe to be reliable and is intended for use, by persons
having knowledge of this technical area, at their own
discretion and risk. Swanstone assumes no responsibility
for results obtained or damage incurred from the use of this
material either in whole or in part by the buyer.
mThis manual will give you basic instructions for the
installation of the product in a step-by-step sequence that
will work in most types of installations. If you have an
installation application that is not covered in this manual,
please call your local Swanstone distributor or contact the
Swan Corporation directly for additional information about
your application.
mFollow all installation instructions. Failure to follow these
instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.
Note: Read All Instructions Before Beginning
Trial Fit
It may be necessary to trim the edge of the vanity top to fit
snugly against the side wall. Install the trimmed edge against
the wall.
Faucet Holes
Note: All Swanstone sinks are manufactured with one
predrilled hole. Optional locations for additional
holes are located on the underside of the sink using
marks (4” and 8”) which are cast into the sink. Follow
Steps 6 and 7 for drilling additional holes to meet the
requirements of the sink faucet or other accessories.
1. If necessary, identify the location of additional holes for the
faucet or other accessories and drill a 1/4” pilot hole from
the back side of the sink.
To prevent damage to the unit, do not use an auger style drill
bit.
Breathing Hazard
When cutting or drilling the Swanstone
product, use a dust collection method
which prevents dust particles from going into the air. Always
work in a well-ventilated area. To keep the area well ventilated,
open windows and use exhaust fans. Always use an OSHA
approved dust mask when cutting, drilling, or sanding
Swanstone products.
VI-001
0” 4” 8”
Swan 6 800-325-7008
Installation Procedure
VI-002
IMPORTANT NOTICE
VI-003
WARNING

2. Drill xture hole(s), using the 1/4” pilot hole for a guide, with
a 1-3/8” hole saw.
3. Faucet may be installed at this time per manufacturer’s
instructions.
Vanity Top Installation — Cabinet Mount
1. Install cabinet per manufacturer’s instructions.
Note: Make sure cabinet is level before installing vanity top.
2. Clean underside of vanity sink with denatured alcohol.
Remove all dust and allow the surface dry completely.
Solvents Hazard
Follow all manufacturers’ safety
instructions for silicone sealants
and denatured alcohol. Alcohol vapors are both flammable
and hazardous to breathe. Silicone vapors may irritate eyes
and nose. Personal injury can result from improperly handling
or use of products, such as denatured alcohol. Always follow
the manufacturer’s recommendations for the safe use of these
products. Ventilate any work area before beginning to apply
silicone sealants, cleaning agents, or solvents.
3. Apply a bead of adhesive or silicone onto each corner of
cabinet top.
800-325-7008 7 Swan
Installation Procedure
VI-008
VI-009
VI-005
VI-007
Denatured
Alcohol
WARNING
VI-004

4. Place Swanstone vanity top onto the cabinet, making sure
vanity is seated properly.
5. Wipe off any excess adhesive, and allow vanity top to set
for 24 hours to ensure maximum adhesion.
6. If desired, use a color-match silicone sealant (not included).
Place a bead of sealant along the seam of the back splash
panel and wall to create a moisture barrier.
7. Apply sealant to the bottom side of the sink ring
Note: When installing the sink ring and tail pipe, use
plumber’s putty sparingly and do not allow it to contact
the plastic overflow assembly under the sink.
To prevent breakage or distortion of the overflow assembly, do
not use oil-based caulking or plumber’s putty near the overflow
assembly. Oil-based plumber’s putty will have a harmful effect
on the plastic overflow assembly, resulting in a leak. If a
sealant is required between the overflow assembly and the tail
pipe, use a silicone sealant.
8. Install tail pipe onto the sink ring.
9. Tighten the tail pipe assembly onto the sink.
Do not overtighten the nut when installing the tail pipe. Hand-
tighten the nut and then tighten NO MORE than one-half turn.
Overtightening will break the overflow assembly and void the
warranty.
Apply Plumber’s
Putty
Here
VI-050
VI-013
VI-006
Swan 8 800-325-7008
Installation Procedure
IMPORTANT NOTICE
VI-051
No Plumber’s
Putty in this
location
VI-052
IMPORTANT NOTICE

10. Connect the faucet supply lines per the manufacturer’s
instructions.
11. Connect the drain lines and p-trap per the manufacturer’s
instructions.
Note: Swanstone recommends using a licensed plumber
for the installation of all necessary plumbing.
12. Turn on the water and check for leaks. Fix any leaks
immediately.
Optional Side Splash Panel Installation
1. Sand back corner of side splash panel to allow ush tting
to vanity top.
Dust Hazard
When sanding Swanstone product,
use a dust collection method which
prevents dust particles from going into
the air. Always work in a well-ventilated area. To keep the area
well ventilated, open windows and use exhaust fans. Always
use an OSHA approved dust mask when cutting, drilling, or
sanding Swanstone products.
2. Trial t side splash to vanity top checking for proper t.
Sand and trim, as needed.
3. Clean the surfaces to be bonded with denatured alcohol,
removing all dust and contaminants. Allow the surfaces to
dry completely.
Solvents Hazard
Follow all manufacturers’ safety
instructions for silicone sealants
and denatured alcohol. Alcohol vapors are both flammable
and hazardous to breathe. Silicone vapors may irritate eyes
and nose. Personal injury can result from improperly handling
or use of products, such as denatured alcohol. Always follow
the manufacturer’s recommendations for the safe use of these
products. Ventilate any work area before beginning to apply
silicone sealants, cleaning agents, or solvents.
4. Apply a thin bead of adhesive or silicone onto back of side
splash panel and attach it to the wall. Wipe off excess
adhesive with denatured alcohol and allow adhesive to set
for 24 hours for maximum adhesion.
VI-010
800-325-7008 9 Swan
Installation Procedure
VI-011
VI-027
WARNING
WARNING
VI-015

5. Caulk all seams between wall and side/back splash to
create a moisture barrier. If desired, use a proper color-
matched silicone sealant (not included).
The installation is now complete. DO NOT discard these
installation instructions. PLEASE LEAVE THEM WITH THE
HOMEOWNER.
Vanity Bowl Installation
Note: If vanity bowl installation is required to be ADA
compliant, refer to the wall mount installation and ADA
sections.
1. Determine desired installation and select appropriate
template.
2. Cut out the vanity top inside of template
.
3. Locate the template, making sure the bowl will not interfere
with cabinet, wall mount, or plumbing.
4. Attach template to counter with masking tape and trace
inside template with a pencil.
5. Drill starter hole inside of cutout line.
6. Use a saber saw to cut inside of cutout line.
Dust Hazard
When sanding Swanstone product,
use a dust collection method which
prevents dust particles from going into the air. Always work
in a well-ventilated area. To keep the area well ventilated,
open windows and use exhaust fans. Always use an OSHA
approved dust mask when cutting, drilling, or sanding
Swanstone products.
7. Trial t bowl and trim or sand as needed for proper t.
8. Clean bowl with denatured alcohol. Remove all dust and let
the surface dry completely.
Solvents Hazard
Follow all manufacturers’ safety
instructions for silicone sealants
and denatured alcohol. Alcohol vapors are both flammable
and hazardous to breathe. Silicone vapors may irritate eyes
and nose. Personal injury can result from improperly handling
or use of products, such as denatured alcohol. Always follow
the manufacturer’s recommendations for the safe use of these
products. Ventilate any work area before beginning to apply
silicone sealants, cleaning agents, or solvents.
VI-029
Drop-In Mount
Swan 10 800-325-7008
Installation Procedure
WARNING
VI-014
VI-030
VI-031
WARNING

Undermount Installation
Note: If undermount installation is required to be ADA
compliant, refer to the wall mount installation and ADA
sections.
Note: Steps 1 through 3 are working from top of the
countertop.
1. Position template on countertop in desired location.
2. Cut opening and nish the edge of the hole.
Dust Hazard
When sanding Swanstone product,
use a dust collection method which
prevents dust particles from going into the air. Always work
in a well-ventilated area. To keep the area well ventilated,
open windows and use exhaust fans. Always use an OSHA
approved dust mask when cutting, drilling, or sanding
Swanstone products.
Note: Remaining steps are working from underside of the
countertop.
3. Place bowl into desired position, making sure that overhang
is uniform and aligned with the cutout.
4. Using 3” wide strips of ¾” thick plywood, trial t the pieces
around bowl perimeter making sure not to cover faucet
openings. Make sure there is 1/4” space between plywood
strips and bowl ange.
5. Using construction adhesive, fasten plywood strips to
countertop surface. For maximum adhesion of plywood strip
to countertop, use the manufacturer’s recommended curing
time.
6. Clean bowl and bottom of the countertop surface with
denatured alcohol. Remove all dust. Let the surface dry
completely.
Solvents Hazard
Follow all manufacturers’ safety
instructions for silicone sealants
and denatured alcohol. Alcohol vapors are both flammable
and hazardous to breathe. Silicone vapors may irritate eyes
and nose. Personal injury can result from improperly handling
or use of products, such as denatured alcohol. Always follow
the manufacturer’s recommendations for the safe use of these
products. Ventilate any work area before beginning to apply
silicone sealants, cleaning agents, or solvents.
7. Apply a bead of silicone around top of bowl ange. Align
and place the bowl onto the countertop.
800-325-7008 11 Swan
Installation Procedure
WARNING
VI-034
VI-036
WARNING
VI-035

VI-038
3” Wide Plywood Strip
Approx.
1/4”
3/4”
8. Attach the sink with clips and screws. Loosely tighten the
screws.
9. If mounting the bowl with an undermount overlap, bowl
should be positioned, as shown.
10. If mounting the bowl with an undermount reveal, bowl
should be positioned, as shown.
11. Verify bowl is in correct position and has not shifted, then
completely tighten screws. Do not overtighten.
12. Use a soft cloth with mineral spirits to remove any excess
silicone.
13. Check for a consistent seal of silicone around inside
perimeter of bowl and countertop. Add silicone if necessary
.
14. Connect the faucet supply lines per the manufacturer’s
instructions.
15. Connect the drain lines and p-trap per the manufacturer’s
instructions.
Note: Swanstone recommends using a licensed plumber
for the installation of all necessary plumbing.
16. Apply sealant to the bottom side of the sink ring.
Note: When installing the sink ring and tail pipe, use
plumber’s putty sparingly and do not allow it to
contact the plastic overflow assembly under the sink.
Swan 12 800-325-7008
Installation Procedure
VI-037
VI-039
3” Wide Plywood Strip
Approx.
1/4”
3/4”
VI-011
VI-010
Apply Plumber’s
Putty
Here
VI-050

To prevent breakage or distortion of the overflow assembly, do
not use oil-based caulking or plumber’s putty near the overflow
assembly. Oil-based plumber’s putty will have a harmful effect
on the plastic overflow assembly, resulting in a leak. If a
sealant is required between the overflow assembly and the tail
pipe, use a silicone sealant.
17. Install tail pipe onto the sink ring.
18. Tighten the tail pipe assembly onto the sink
Do not overtighten the nut when installing the tail pipe. Hand-
tighten the nut and then tighten NO MORE than one-half turn.
Overtightening will break the overflow assembly and void the
warranty.
Note: When installing the sink ring and tail pipe, use
plumber’s putty sparingly and do not allow it to contact
the plastic overflow assembly under the sink.
19. Install tail pipe onto the sink ring.
The installation is now complete. DO NOT discard these
installation instructions. PLEASE LEAVE THEM WITH THE
HOMEOWNER.
ADA Installation Recommendations
In order to comply with ADA requirements, the lavatory must
have adequate floor clearances in front of the sink. It must
also be installed at the proper height with the specified leg and
wheel chair clearance under the sink.
Installing the vanity top using the supplied specifications does
not imply the bathroom in which it is installed will comply with
ADA standards. It is the responsibility of the installer/designer
to ensure that all the components of the bathroom are in
compliance with ADA standards, including the lavatory.
For complete guidelines and compliance, refer to ADA Section
606 Lavatories of the Act.
Clear Floor Space
A clear floor space, in front of the sink, for a forward approach
must be at least 30” (76.2 cm) wide and 48” (121.9 cm) long,
as shown in the illustration. These measurements are in
compliance with ADA standard 606.2.
Note: In residential bathrooms, cabinetry is permitted
under lavatory sink provided that all of the following
conditions are met:
(a) the cabinetry can be removed without removal or
replacement of the fixture;
(b) the finish floor extends under the cabinetry; and
(c) the walls behind and surrounding the cabinetry are
finished.
800-325-7008 13 Swan
IMPORTANT NOTICE
Installation Procedure
IMPORTANT NOTICE
IMPORTANT NOTICE
VI-051
No Plumber’s
Putty in this
location
VI-052
ADA-LB-001a
30”
MIN.
Clear Floor Space
48”
MIN.
19”
MAX.

Accessibility Requirements
Note: Only lavatory installations in a public space must
comply with the knee and toe clearance
dimensions,however we recommend these standards
be used for both private and commercial installations.
Also makesure that all state and local building codes
are followed when installing this unit.
m The top of the vanity should not exceed 34” (86.4 cm) from
the oor.
m The “knee space” below the apron of the vanity top should
be a minimum of 27” (68.6 cm) from the oor.
m The front edge of the sink should be between 17” (43.2 cm)
and 25” (63.5 cm) from the wall.
m The faucet should be a maximum of 19” (48.5 cm) from the
front of the sink.
m No part of the sink or the plumbing should be within the gray
area shown in the drawing.
Care and Cleaning
The Swanstone products are stain and abrasion resistant;
however, the finish requires reasonable care.
Because cleaning products change over time, always check
the manufacturer’s instructions to make sure it is compatible
with plastic. DO NOT use a cleaner if the label indicates
it should not be used on plastics. DO NOT use spray-on
cleaners that require daily use without immediately rinsing with
water to stop the chemical cleaning reaction because damage
will result and void the warranty.
Day-To-Day Cleanup
Clean your Swanstone vanity top with powdered abrasive
cleaners. Use of a Scotch Brite pad is recommended to
remove stubborn stains. Occasional use of a mild bleach and
water solution ensures that the original luster is maintained.
Simply wipe the surfaces with a clean towel to remove
watermarks and residues. All Swanstone products can be
cleaned with warm water, a soft cloth, and normal household
detergents or cleansers, such as Fantastic, Formula 409,
Clorox Clean-up, Handy Andy, Mr. Clean, or Lestoil. Always
rinse off cleaners within five minutes of application.
Occasional scrubbing with household abrasive cleaners
ensures that the original luster is maintained.
For the most stubborn stains, fill the Swanstone vanity bowl
about one-quarter full with a 50/50 solution of bleach and
water. After ten or fifteen minutes of soaking, drain solution
from the bowl as you wash and rinse both sides and bottom.
Note: Do not use steel wool or metal scourging pads
Cleaners designed to remove iron or rust should not harm
Swanstone.
White automotive rubbing compound may be used to remove
stubborn marks or discoloration.
Surface Repair
Light Scratches
Use 400 grit sandpaper to remove light scratches in the
surface.
Deep Scratches or Gouges
For deeper scratches or gouges, use 220 or 320 grit
sandpaper. A “Scotchbright pad” can be used to blend the
repair into the surrounding area.
Swan 14 800-325-7008
Installation Procedure Maintenance and Cleaning
ADA-LB-002a
17” Minimum
25” Maximum
19” (48.5 cm)
MAX.
27”
(68.6 cm) Minimum
34”
(86.4 cm) maximum
ADA-LB-003a
6” (15.2 cm)
9” (22.9 cm)
8” (20.3 cm)
IMPORTANT NOTICE

800-325-7008 15 Swan
Warranty
If a Swan product covered by this warranty is found to be
defective in materials or workmanship, after inspection by an
authorized Swan Corporation representative, we will repair, or
at our option, exchange the product for a similar model. This
warranty extends for a designated period of time, so long as it
remains in use in its original place of installation.
This warranty covers products installed in accordance with
the Swan Corporation’s installation instructions, used as
recommended, and not damaged due to misuse, abuse,
or improper installation. It does not apply to any seams or
changes made to the product by professional tradesmen or
fabricators.
The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or other
costs of removal or installation, nor shall the Swan Corporation
be responsible for any other incidental or consequential
damages attributable to a product defect or to the repair or
exchange of a defective product.
Residential Limited Lifetime Warranty
The warranty applies only to the original purchaser and
installation of these products in residential applications. It does
not apply to commercial applications.
Commercial 25-Year Limited Warranty
The warranty applies only to the original purchaser and
installation of these products in commercial applications.
Warranty

Swan 16 800-325-7008

800-325-7008 17 Swan

www.swanstone.com Form #255-05-16
Save these Installation Instructions for future reference. They provide
important information on cleaning, maintenance, and surface repair of the
Swanstone Products.