Swiss Madison Freestanding Vanity User manual

www.swissmadison.com | 1-434-623-4766 | [email protected]
Swiss Madison
®
INSTALLATION INSTRUCTIONS
Freestanding Vanity
@SwissMadison
#WellMadeForever

—1 —
If you have any questions or concerns please contact us:
1-434-623-4766
[email protected]
PRIOR TO INSTALLATION:
· Inspect product to ensure no damages have occurred while in shipping.
· Observe all plumbing and building codes in accordance with your state and local requirements.
·Floor must be level prior to installation of vanity.
· All dimensions are nominal! Be sure to measure your vanity prior to installation.
· The step-by-step guidelines in the installation instructions are a general reference. Should there be
any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss
Madison products by hiring a licensed professional.
· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper
tools and always wear proper personal safety accessories for your protection.
INCLUDED PARTS:SUGGESTED TOOLS & MATERIALS:
Vanity
Sink
Vanity
Base
FREESTANDING VANITY INSTALLATION INSTRUCTIONS
Adhesive
Drop Cloth
Silicone
Gloves
Safety
Glasses
Level
Hardware
Screwdrivers
Allen
Wrench
Drill

FREESTANDING VANITY INSTALLATION INSTRUCTIONS
—2 —
1. Install Hinges
·Screw 9 cam bolts (A) into the left side panel (1) and use 8 screws (G) to install the 2 hinges (E).
·Screw 9 cam bolts (A) into the right side panel (2) then use 12 screws (G) to install the 3
undermount slides (K).
·Screw 1 cam bolt (A) and 4 cam locks (B) into the middle panel (8), then use 12 screws (G) to
install the 3 undermount slides (K). On the other side of the middle panel (8) use 8 screws (G) to
install the 2 hinges (N).
·Screw 4 cam bolts (A) to the front bottom bar (13). Insert 4 wooden dowels (C) and screw 6
cam bolts (A) to the bottom panel (3). Invert the bottom panel (3) and use 4 cam locks (B) to
attach the front bottom bar (13) to the bottom panel (3).
·Screw 1 cam bolt (A) to the rear top bar (4). Repeat for the rear bottom bar (5).
C
C
C
C
A
A
A
A
A
A
A
B
BB
B
B
BB
B
B
B
B
B
A
A
A
AA
3
5
13
4
A
A
A
A
A
B
BB
B
A
AA
A
A
A
G
G
GG
GG
GG
GG
G
G
K
K
K
K
K
K
GG
G
G
GG
G
G
AE
E
AAAAA
A
A
1
2
8
Parts for Reference:
1. Left side panel
2. Right side panel
3. Bottom panel
4. Rear top bar
5. Rear bottom bar
6. Left door
7. Right door
8. Middle panel
9. Top drawer surface
10. Middle drawer surface
11. Bottom drawer surface
12. Front top bar
13. Front bottom bar
14. Drawer left side panel
15. Drawer right side panel
16. Drawer back panel
17. Drawer front panel
18. Drawer bottom panel
A. Cam bolt
B. Cam lock
C. Wooden dowel
D. Metal bracket
E. Hinge
F. Screw (10mm) & plastic anchor
G. Screw (14mm)
H. Screw for handle (22mm)
I. Screw for drawer (20mm)
J: Screw for drawer (25mm)
K: Undermount slide
L: Handle
M: Screw for handle (30mm)
N. Hinge
1
2
3
6
7
4
5
x3
x3
x3
x3
x3
12
9
10
11
13
14
15
16
17
18
8
14mm
20mm
25mm
30mm
10mm
22mm
A
G
H
I
J
K
L
M
B
C
D
E
N
F
GG
G
N
N
G
GG
G
G

—3 —
2. Assemble Base
·Attach the rear bottom bar (5) and the middle panel (8) to the bottom panel (3) by locking the
6 cam locks (B), then insert the 2 wooden dowels (C) to the front top bar (12).
·Use 9 cam locks to connect the left side panel (1) to the bottom panel (3), rear top bar (4),
and front top bar (12). Repeat to connect the right side panel (2).
3. Assemble Drawer Base
·Screw 6 cam bolts (A) into pre-threaded holes on
the drawer left side panel (14). Repeat for the
drawer right side panel (15).
·Screw 2 cam bolts (A) into the drawer back panel
(16). Repeat for the drawer front panel (17).
·Use 16 cam locks (B) to connect and secure all
panels in place as shown.
4. Assemble Drawers
·Attach the 2 undermount slides (K) to the drawer
bottom panel (18) with 2 screws (I). Repeat the
process for the remaining two drawers. Do not
tighten screws all the way.
·Attach the drawer front panel (17) to the door
surfaces (9 & 10 & 11) with 4 screws (J) as shown.
·Insert the hooks of the slides (K) to the back panel
of the drawer (16). Tighten the 2 screws (I) on the
bottom of the drawer (18) to secure the slides (K).
Repeat the process for remaining the two drawers.
A
FREESTANDING VANITY INSTALLATION INSTRUCTIONS
14
15
16
18
A
A
A
A
A
A
A
B
B
B
B
BBB
B
B
B
B
B
A
A
A
14
15
16
17
AA
A
AA
A
AA
A
A
A
A
A
A
A
A
I
K
2
8
4
12
13
2
8412
1
3
5
C
C
A
A
A
AAA
A
A
B
B
BB
B
BB
B
B
BB
BBB
BB
BB
B
18
B
B
B
B
15
14
17
16
x3
B
J
J
J
J
B
B
B
15
14 17
18
16
10 11
9x3

—4 —
5. Install Doors
·Use 24 screws (G) to attach the left door (6) and
right door (7) to the cabinet. Install the 2 handles (L)
to the 2 doors and 3 handles (L) to the 3 drawers
using the 5 handle screws (M).
·Adjust the hinges to make the doors in the correct
position if necessary.
6. Secure Vanity to Wall
·Attach 2 metal brackets (D) to the rear top bar (4)
using 16 screws (G).
·Mark the desired hole locations on the mounting
wall. Once satisfied with the placement, predrill
holes into the mounting wall.
·Install the vanity to the wall by using 2 screw &
plastic anchor sets (F).
FREESTANDING VANITY INSTALLATION INSTRUCTIONS
GG
GG
7
GG
E
E
N
N
GG
6
F
F
L
ML
L
L
L
7
6
9
10
11
2 pcs
·If adjustment or realignment is needed, follow the instructions provided in the following chart.
Hinge/Door Adjustment and Realignment
1. Loosen screws 2. Adjust hinge 3. Tighten screws
Vertical
adjustment
Horizontal
adjustment
Door gap
adjustment

—5 —
7. Vanity Top Installation
·Install faucet and drain according to manufacturer’s installation instructions. Do not overtighten, this may
cause the sink to crack.
·Set the vanity top on top of the vanity base, checking the location of the p-trap and drain.
·Remove vanity top from vanity base. Apply a thin bead of silicone around the vanity base and set the vanity
top carefully in place.
·Remove excess silicone with a wet cloth.
Wait 24 hours
before use.
24H
!
FREESTANDING VANITY INSTALLATION INSTRUCTIONS

1-434-MADISON
(623-4766)
19 Stults Road
Dayton, NJ 08810
www.swissmadison.com
ONE YEAR LIMITED WARRANTY
Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our
customers with beautiful, durable, long-lasting products. Should there be any defects in materials or
craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison®
will provide replacement parts at no charge, or at its discretion, replace any product or part of the product
that is deemed defective, under normal installation, use, service or maintenance. This warranty applies
only to the original purchaser. Proof of purchase will be required in the instance of a claim.
Swiss Madison® recommends all installations of Swiss Madison® products to be conducted by a
licensed, professional plumber or contractor. Swiss Madison® will not be held responsible for any
damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional
for installation. Swiss Madison® is not responsible for any installation or removal costs.
This One Year Limited Warranty Will Be Voided If:
• The installation recommendations were not followed by the installer
• The product has been moved from its initial place of installation
• The product has in any way been modified from its packaged state
• The product has been subjected to improper maintenance, abuse, misuse, excessive use of
chemicals, accidents, or other damages, etc.
Swiss Madison® makes no implication that its products comply with any local building or plumbing
codes. It is the consumer’s responsibility and obligation to determine local code compliance prior to and
during installation. This warranty extends only to the original purchaser and first consumer.
Swiss Madison® is not responsible for any special, incidental or consequential damages associated with
the installation, replacement, return or use of the original purchaser’s product. This includes, but is not
limited to: freight costs, labor, travel time, lost profit, home damages and other contingent liabilities and
costs (including, without limitation, costs associated with ‘professionals’ or ‘experts’, investigations,
audits, analyses, attorneys and any other professional/hired services).
The Swiss Madison® warranty is a comprehensive and explicit limit of liability. All items not disclosed
within the warranty are not addressable within the responsibility of Swiss Madison®. Certain states have
variances regarding implied warranties; in those situations, we remain fully compliant.
If you have any questions or concerns, please contact us directly at
1-434-MADISON (623-4766)
WARNING: Contents of your order may contain sharp and possibly other harmful pieces and may
cause hazard to children and adults. Swiss Madison® is not responsible in any way for personal dam-
ages.
Swiss Madison
®