Telesystem Palco19 LED07 T2S2HEVC User manual

TELE System
1

1
Dear Customer,
in thanking you for purchasing our product, please read the following
instructions before attempting to operate the unit. This is the only way to
achieve the best results over time while maintaining the original reliability. We
also suggest that you keep this manual for any future reference. We also
suggest that you keep the original packaging of the TV and, in the event of any
problem, remember to take note of the serial number of the TV which is shown
on the back of the device.
The TELE System staff
ATTENTION!
The reception and therefore the viewing of channels in digital terrestrial and/or
satellite depends on the level and quality of the available antenna signal. The
signal varies depending on the area of residence, the correct
orientation/functioning of the antenna system, and the quality of the signal
transmitted by digital terrestrial repeaters and/or satellites.
TELE System Digital Srl announces that due to software and/or hardware
changes that aim to improve the product, you may find inconsistencies between
the contents of this manual and the product in your possession.

2
Index
1!Safety......................................................................................................................... 3!
2!Description of the TV ........................................................................................... 5!
2.1!Front .........................................................................................................5!
2.2!Keyboard...................................................................................................5!
2.3!Rear panel connections............................................................................6!
3!Connections .............................................................................................................. 7!
3.1!Antenna connections/cable TV channel...................................................7!
3.2!Connection to an external device.............................................................7!
4!Remote Control ....................................................................................................... 8!
4.1!Standard remote control..........................................................................8!
4.2!Simplified remote control ........................................................................9!
4.3!Inserting batteries..................................................................................10!
5!PC Mode .................................................................................................................. 10!
5.1!MENU FOR PC MODE .............................................................................10!
6!Basic Function....................................................................................................... 11!
6.1!Power / Standby .....................................................................................11!
6.2!Program selection..................................................................................11!
6.3!Volume regulation ..................................................................................11!
6.4!Mute (temporary)....................................................................................11!
6.5!Program recall .......................................................................................11!
6.6!Source selection.....................................................................................11!
6.7!Main Menu description...........................................................................12!
6.8!First installation .....................................................................................12!
6.9!Automatic channel search. ....................................................................12!
7!DVB Mode ............................................................................................................... 13!
7.1!Manual search........................................................................................13!
7.2!Electronic TV guide (EPG).......................................................................13!
7.3!Organization of channel list. ..................................................................14!
7.4!Favorites list...........................................................................................14!
8!Satellite mode ...................................................................................................... 14!
8.1!Simple installation .................................................................................15!
8.1.1!Antenna and satellite configuration...............................................15!
8.1.2!Channel search for satellite...........................................................15!
8.2!SCR/Unicable System.............................................................................16!
8.3!System DiSEqC 1.0/1.1 ...........................................................................16!
8.3.1!Antenna e satellite configuration...................................................16!
8.3.2!Channel search for satellite...........................................................17!
8.4!Motorized System...................................................................................17!
8.4.1!DiSEqC 1.2 ......................................................................................17!
8.4.2!DiSEqC 1.3 ......................................................................................18!

3
8.5!Automatic scanning................................................................................19!
9!Security – System Block....................................................................................20!
10!Image Menu.........................................................................................................20!
11!Audio Menu ..........................................................................................................21!
12!Time settings ......................................................................................................21!
13!Settings Menu ....................................................................................................21!
14!USB Media player...............................................................................................22!
15!Troubleshooting ................................................................................................. 23!
16!Technical Specifications..................................................................................25!
1Safety
ATTENTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE
BACK COVER AND DO NOT USE METAL TOOLS.
Before connecting the power cord to the DC adapter outlet, make sure that the
voltage corresponds to the one used in your area.
Make sure your TV is switched off before inserting the mains plug into the wall
socket. Be careful to ensure that the electrical cable and other connecting
cables are firmly connected and secure.
Voltage overload and power extension cables can be dangerous, just as frayed
wires or broken sockets/plugs; These conditions may cause electric shock or
fire. Contact a trusted technician to replace the damaged parts.
Do not insert metal objects into the TV; there is a danger of electric shock.
To avoid electric shocks, do not touch the internal parts of the LED TV; only
qualified personnel can open the television.
The TV is equipped with slots for air circulation. To prevent overheating, these
openings must not be covered or obstructed. If you place the TV in confined
spaces (within libraries or other furniture), make sure that there is adequate
ventilation.
Do not use the television with extreme temperatures, humidity, or in dusty
environments.
The recommended use temperature: 5-35 ° C
Relative humidity: 30 – 80RH
Do not expose your TV to rain or splashing water; do not install it near kitchens,
swimming pools etc ... If liquid accidentally gets inside the TV, unplug the power
cord immediately and contact a technician.
You can clean the LED/LCD screen if necessary with a damp soft cloth,
remember to unplug the TV before cleaning.
Do not use solvents such as benzene to clean the device, because you will
damage the screen surface.
Place the TV on a firm surface and handle with care.

4
The screen is formed by a thin glass and protected by a plastic foil, liquid
abrasives or streaks will permanently ruin the LED/LCD panel.
Do not clean the screen with substances such as acetone, ethyl alcohol, toluene,
ethyl acid, methyl or hydrogen; these substances ruin the LED/LCD panel.
Position the TV so that it is easier to access the power outlet.
Do not put heat or flame such as candles near/on the TV.
No object filled with liquids such as vases or bottles should be placed on or near
the TV.
The checked bin symbol indicates that you should not dispose of this
product in the environment or throw it in the mixed municipal waste.
Whoever does not respect this rule is punishable according to current
legislation.
A proper disposal of the appliance enables you to avoid potential damage to the
environment and human health as well as to facilitate recycling of components
and materials contained in it and save enery and resources.
The manufacturer provides a system for recovery of electric and electronic
appliances (RAEE or WEEE) such as this product which is collected separately
and subject to treatment systems with equipment in accordance with current
provisions.
Take the unusable product (and any accessories, including the battery) to a
recycling center authorized to handle electrical and electronic equipment waste,
as it cannot be combined with other waste. You can always return the used or
dead device to the same distributor who sold it to you while buying a new
equivalent product or free of charge if the equipment is for home use and is
smaller than 25cm.

5
2Description of the TV
2.1 Front
LED: Status Indicator, Red = Standby, Green = Power
IR sensor: remote control receiving sensor
Warning! The position of the LED and IR sensor may not correspond exactly to
the one shown in the picture.
2.2 Keyboard
The TV keyboard is on the right side of TV itself. The available keys are (from left
to right):
Vol-: increase volume
Vol+: decreases the volume
CH-: change to the next channel
CH+: change to the previous channel
Menu: access the main menu
Source: select source
Power: Standby mode (OFF/ON)

6
2.3 Rear panel connections
On the back side of the TV, there are connections and A/V inputs; horizontal side
(from left to right):
12V power supply (DC IN 12V)
Headphone output (3.5 mm jack)
VGA port (PC)
SCART input
PC Audio input (PC Audio IN)
SATELLITE RF Antenna Input (Type F)
TERRESTRIAL Antenna RF input (IEC)
Coaxial digital audio output (COAXIAL)
On the verticle side (from top to bottom):
Component input (YPbPr, adapter required)
RCA Video + Audio input (AV, adapter required)
Common Interface slot (compatibile with CI+ module)
USB port (Media Player Fuction)
HDMI input

7
3Connections
3.1 Antenna connections/cable TV channel
To view the television channels, you can connect the TV to one of the following
devices:
A terrestrial antenna and/or a satellite antenna system.
In either case, connect the antenna cable (75 Ω) to the coaxial jacks located in
the rear of the TV.
3.2 Connection to an external device
Via SCART: make sure that both the TV and the device are turned off. Connect
the SCART cable from the source to the TV. Turn on the two devices.
Press the Source button on the remote control and select SCART.
Via RCA: make sure that both the TV and the device are turned off. It is
necessary to use an RCA/Jack3.5mm adapter to connect the device to the
AV/RCA input. Turn the two devices on. Press the Source button on the remote
control and select AV as the source.
Via YPbPr (Component): make sure that both the TV and the device are
turned off. It is necessary to use an RCA/3.5mm jack adapter to connect the
device to the AV/RCA, respecting the colors as per the following instructions:
Yellow - Green
Red - Red
White - Blue
Turn on the two devices.
Press the Source button on the remote control and select YPbPr.
Via HDMI: make sure that both the TV and the device are turned off. Connect
the cable from the source to the TV. Turn on the two devices.
Press the Source button on the remote control and select HDMI.

8
4Remote Control
4.1 Standard remote control
POWER:On / Off Stand-by
Mute: temporary interruption of audio.
Source:source selection
Video:change the video mode.
Sound:change the audio mode
AUDIO: audio choice.
A.Ratio:choice of image format.
TASTI NUMERICI: direct channel selection.
FAV: Displays the favorite channel list.
SLEEP: sets the sleep timer.
BACK: back to the last selected program.
MENU: display the main MENU.
INFO: displays information of current channel.
EXIT: exit the menu.
ARROW KEYS: are used to browse through the menu /
regulate volume / change sequential channels
OK: Confirm or select a sub-menu.
Access the channel list
V -/+: Decrease / increase volume.
P -/+: change previous / next channel.
D.SETUP: not active
REPEAT: not active
ZOOM: not active
GOTO: not active
RED FASTEXT KEY
GREEN FASTEXT KEY
YELLOW FASTEXT KEY
BLUE FASTEXT KEY
DVBT: switches to DVBT mode/ Index in Televideo mode.
SAT: switches to SAT mode / Reveal in Televideo mode
USB: switches to USB (Media) mode/Zoom inTelevideo
mode
DTV/RADIO: changes the viewing modality, between TV programs and Radio
programs or Hold in Televideo.

9
TIMESHIFT: activates the Timeshift function
■: stops the playback/recording
: not active
►▌▌: starts / pauses playback
◄◄/►►: rewind / fast forward
▐◄◄/►►▌: back forward one track / song / picture
TXT: accesses the Televideo.
SUBTITLE: activates subtitles (if present)
GUIDE: electronic program guide (EPG)
4.2 Simplified remote
control
POWER: Stand-by On/Off
TXT: access Televideo.
EXIT: exit the menu.
NUMERIC BUTTONS: direct selection of
channels.
Source: source selection.
Mute: temporary interruption of audio.
ARROW KEYS: are used to browse through the
menu / regulate volume / change sequential
channels
OK: Confirm or select a sub-menu. Access the
channel list

10
4.3 Inserting batteries
You have to replace or install the batteries when:
•You buy the product.
•the remote control does not work properly.
Once you open the battery door located on the back of the remote, insert the 2
batteries (AAA) in the compartment, making sure to respect the correct polarity
as indicated.
Remove the used batteries, which must be disposed of separately from
household waste taking them to any store or collection point and then repeat
the operations for insertion.
To avoid damaging the remote control with the leakage of corrosive liquid, you
should remove the batteries if you plan not to use the device for a long period of
time. Avoid using different types of batteries or dead and new batteries at the
same time.
5PC Mode
Since it is equipped with a VGA video card, the TV can be used as a PC screen
following this procedure:
With the equipment turned off, connect the two devices via a D-SUB cable (15-
pin) for the Video part and an audio cable for the audio portion.
Reset the electrical connection of the TV and PC. Turn on the TV and from your
remote control, press the AV button. Select the PC mode.
Turn your computer on.
5.1 MENU FOR PC MODE
After switching to PC mode, you can adjust various settings by pressing the
MENU button on the front panel or the remote control: the usual menu will
appear, which will have some functions active only in this mode: to navigate
through the menu use the ▲/▼keys. Change the values using the t/ u
buttons.

11
6Basic Function
6.1 Power / Standby
While the TV is in operation, to turn it off, press the Power button on your
remote control. The LED on the front panel of the TV will change from green to
red.
To switch the TV on again, press the Power button (on the remote control or on
the TV).
6.2 Program selection
To select a program, press the P+/P-buttons or the / buttons on the
standard remote control for a sequential selection; use the numeric keys for
direct channel selection.
6.3 Volume regulation
Press the V- / V+ buttons or the buttons t/ uon the standard remote control
to increase / decrease the volume.
6.4 Mute (temporary)
Pressing the MUTE button, the sound is interrupted and the video shows the
symbol of the function. To reactivate the sound, you can press the MUTE button
again or one of the volume buttons V- / V +.
6.5 Program recall
You can recall the previously selected program by pressing the BACK button
and by pressed it again, it returns to the program you were watching.
6.6 Source selection
By pressing the Source button, you can select the TV mode:
DTV: To activate the Digital TV mode and allow the reception of digital TV
programs;
SCART: To enable SCART input
AV: to enable the AV input (RCA)
YPbPr: to activate the YPbPr input.

12
HDMI: to activate the HDMI input.
PC: to activate the PC mode
USB: to access content loaded on a USB memory. (See Chapter 16)
6.7 Main Menu description
Press the MENU key to bring up the main menu and use the arrow keys ▲/▼
and t/ uto navigate through the titles of menu. Press the MENU button to
return to the previous menu or EXIT to exit. The menus are: Channels,
Images, Sound, Time, Security, Settings .
6.8 First installation
When the TV is turned on for the first time or after a factory reset, a wizard will
allow the simple and optimal installation of the TV:
Select the installation language (OSD Language) with the t/ uarrow keys
(default Italian). Go on to the next step by pressing the ▼button.
Then select the installation country (Italy default) using the arrow keys t/ u
Press OK to move on to the next step.
Select the tuner signal type (DVB-T2 or Satellite) to start searching for channels
and press OK to start an auto scan.
At the end of the DVB-T2 scan, a list of LCN conflicts to be resolved manually
will appear. The user can choose the channel to be assigned to each disputed
LCN position manually or automatically all at once (recommended).
If you choose satellite, you can choose to load a default satellite channels list by
pressing OK and confirming Yes (left arrow) to the confirmation request; or
proceed with normal installations, once the satellite parameters are set, scan
type, channel type and type of service, by pressing OK and choosing No (right
arrow) on the next screen.
6.9 Automatic channel search.
Press the MENU button; in CHANNEL menu using ▼, select the entry Auto
tuning and confirm with the OK button.
Select the country of installation (default Italy) and press OK to start an
automatic channel search.
At any time you can:
Press EXIT or Menu to terminate the search

13
ATTENTION!
The automatic channel search cancels all the previously memorized channels.
7DVB Mode
To activate the reception mode for digital channels, press the Source button,
choose DTV.
You can scan the frequencies available in your area, searching all digital
channels automatically (see section 6.9) or manually.
ATTENTION!
The reception and therefore the viewing of digital terrestrial channels depends
on the level and the quality of the antenna signal available The signal varies
according to the area in which you live, to the correct orientation/functioning of
the antenna system and to the quality of the signal transmitted by the digital
terrestrial repeaters.
7.1 Manual search
Press the MENU button; in the CHANNEL menu using ▼select the item DTV
Manual tuning and confirm with the OK button
Enter the channel (frequency) to be searched for through the ◄/ ►buttons on
the remote and confirm with the OK button.
Press the EXIT button to cancel manual search at any time.
7.2 Electronic TV guide (EPG)
The Electronic TV Guide, if supported by the broadcaster, offers information on
the TV programs shown for the subsequent 7 days. To activate this feature (only
in DTV mode) press Guide on the remote control.
Use the arrow keys to select the channel and/or program to view a brief
description of the event.
Use the P + and P- if the event description provides more pages.
Position yourself on "Time" and use the arrows keys ◄/ ►to switch the
display mode.
Press the blue "Reminder" button to create an event reminder, a warning
message will appear on the screen informing you of the imminent start of the
highlighted program.

14
7.3 Organization of channel list.
Press the MENU button; in CHANNEL menu, select the item using ▼, Program
Edit and confirm with the OK button.
You will see the channel list with the following options available:
Red button (Delete): to delete one or more channels select the channel with
the ▲/▼, buttons and press the red button to confirm the cancellation.
Blue button (Skip): select the channel and press the Blue button; if activated,
the channel can only be displayed when recalled by using the number buttons
on the remote.
Yellow button (Move): to move a channel, select the channel you want to move,
press the Yellow button, use the arrow keys to move the channel to the desired
position or enter the desired position number, then press OK to confirm.
7.4 Favorites list
You can create a favorite channels list for DTV channels (terrestrial signal):
Once the option Program Edit and the channel you want to add to the Favourites
list has been selected, press the FAV button; Repeat for each channel you want
to add. After you create the list, to access it, simply press the FAV button and
select the channel with the arrow keys ▲/▼and OK to confirm.
You can later remove one or more channels by performing the same procedure,
selecting the channel you want to delete, and pressing the FAV button.
8Satellite mode
To activate the digital channel reception mode, press the Source button, select
Satellite.
You can scan the frequencies available with your satellite antenna system,
automatically searching for all the satellite channels from the first installation
(see paragraph 6.8) or through an automatic scanning available in the Channels
menu.
Dish Setup: the basic settings to allow the use of the TV with a single Universal
LNB (Low Noise Block converter) system (commonly used for satellite systems
in Italy); in the event your system is done with a different configuration, you
must appropriately change the antenna settings.
ATTENTION!!!
The wrong antenna configuration can result in the failure to load some or all
channels. If you do not know the characteristics of your antenna system and/or
are unable to properly configure the receiver yourself, you may want to consult

15
a professional installer for advice. The power and signal quality indicators refer
to the first transponder of the chosen satellite list.
Changing the DiSEqC 1.0 / 1.1 parameters, DiSEqC 1.2 / DiSEqC 1.3 , you will get
three different configuration modes.
8.1 Simple installation
For the single inverter antenna (LNB)/satellite with direct connection between
the TV and antenna, they DiSEqC commands or other special communication
protocols are not used.
8.1.1 Antenna and satellite configuration
From the Antenna setup menu make the following choices:
1. Satellite : Satellite choice of interest. Highlight the Satellite confirm by
pressing OK and press ►.
1. LNB type : Type of converter (Low Noise Block converter - LNB) associated
to the chosen satellite. For common satellite systems used in Italy, The
Universal (9750/10600) is used.
2. LNB power : LNB power supply for switching between horizontal and
vertical polarization. Generally it must be maintained active (13 / 18V). Its
inactivation is rather useful when you realize IF-IF distribution plants (for
Expert users).
3. 22KHz : 22KHz signal switching between high and low band
2. Tone burst : none
3. DiSEqC 1.0 : none
4. DiSEqC 1.1 : none
5. Motore: none
8.1.2 Channel search for satellite
After setting the configuration, to search channels on the chosen satellite press
the BLUE button Scan and define the following parameters in the Channel
Search dialogue window:
1. Scan type : scanning mode following the transponder database (default
option) or blind-scan frequency steps (Blind-Accurate option) or via
network (network option) that scans the active transponders.
2. Channel type : choose free to air channels to only search for Free
channels (recommended), Scramble only for encrypted channels or
Free+Scramble to scan both types.

16
3. Service type : choose DTV to only search for TV channels, Radio to only
search for radio All
4. Press OK to start scanning.
8.2 SCR/Unicable System
For single-antenna converter (LNB) / satellite installations with SCR / Unicable
technology for the distribution of satellite signals to multiple points of use
(receivers) with a single cable, you must set the LNB type with the Unicable
value and enter the appropriate configuration:
Canale IF : User number corresponding to the channel assigned to the
TV/Receiver regarding the SCR system. Each receiver connected to the same
system must use a different IF channel.
Central Freq. : main frequency of the band/SCR channel assigned to the user.
Typical values for interfacing with other receivers/tuners are
IF Channel
1
2
3
4
Freq.
1210
1420
1680
2040
Press Exit to save settings and return to the previous screen and continue with
the channel search as shown in paragraph 8.1.2.
CAUTION
If two receivers are connected in cascade to the antenna signal via the LNB OUT
pass-through connector, they can not operate simultaneously. When a receiver
is switched on, the other must be placed in stand-by (not supplied with the
tuner) and vice versa
To connect multiple receivers to a SCR system, do not use the connection
through antenna receiver, but use a suitable divider external signal.
8.3 System DiSEqC 1.0/1.1
The DiSEqC 1.0 / 1.1 protocol has been developed for receiving multiple
satellites via antenna systems with multiple converters, also known as multi-
feed, and up to four different orbital positions for the DiSEqC 1.0 and up to
sixteen for DiSEqC 1.1.
8.3.1 Antenna e satellite configuration
From the Antenna Set Up perform the following options:
1. Satellite : chose the desired satellite. Highlight the satellite and press OK
to confirm and press ►.

17
2. LNB type : inferior/superior frequency of the local oscillator of the
converter
3. LNB power : LNB supply for switching between horizontal and vertical
polarization
4. 22KHz : signal at 22KHz switching between high and low band
5. Tone burst : none.
6. DiSEqC 1.0 o DiSEqC 1.1 : select the LNB number based on its aerial
system (i.e. Dual-feed: Hot Bird 13°E on LNB1 and Astra 19.2°E on LNB2)
7. Motor: none.
NOTE
Repeat the above procedure for each satellite for which you want to perform a
channel search
8.3.2 Channel search for satellite
Se the procedure illustrated in paragraph 8.1.2
8.4 Motorized Antenna
The configuration differs depending on the type of engine used to implement the
system, the TV is able to control the movement/rotation of the antenna manually
(DiSEqC 1.2) or semi-automaticlly (also known as DiSEqC 1.3 USALS).
8.4.1 DiSEqC 1.2
From the Antenna Setting menu, make the following choices:
1. Satellite : chose the desired satellite. Highlight the satellite and press OK
to confirm and press ►.
2. LNB type : inferior/superior frequency of the local oscillator of the
converter
3. LNB power : LNB supply for switching between horizontal and vertical
polarization
4. 22KHz : signal at 22KHz switching between high and low band
5. Tone burst : none
6. DiSEqC 1.0 : none
7. DiSEqC 1.1 : none
8. Motor : DiSEqC 1.2