Temco Vfl34rn User manual

Installation and Operating

Instructions for Gas Log

Heaters

Models: VFL34RN, VFL34RP

Models with “N” after the model number use natural gas; models with “P” after the model number use propane (LP) gas.

READ AND SAVE THESE INSTRUCTIONS

This appliance operates as an unvented room

heater certified under ANSI Z21.11.2-2000 when

fitted to a solid fuel burning masonry or factory

built fireplace with the flue damper closed. It also

operates as a decorative appliance under ANSI

Z21.60a-2000.CSA 2.26a-2000, when fitted to a solid

fuel burning masonry or factory built fireplace with

the flue damper open. When used as a decorative

appliance, the use of a thermostat is not allowed.

State or local codes may only allow operation of

this appliance in a vented configuration. Check

your state or local codes.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions

for adequate combustion and ventilation air must be provided. Refer to Section Provisions For Adequate

Combustion and Ventilation Air - Page 4.

FOR YOUR SAFETY

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier’s instruc-

tions.

•If you cannot reach your gas supplier, call the fire department.

—Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

78570 11/03 Rev. 6

5L24

410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777

Temco Fireplace Products

Gas Fired

Unvented

Room Heaters

78570

Minimum Dimensions for Existing Solid Fuel Burning Fireplaces ............................................2

Important Information ...............................................................................................................3

Provisions For Adequate Combustion Air .................................................................................4

Installation

Unpacking.................................................................................................................................6

Fireplace Preparation ...............................................................................................................6

Location ....................................................................................................................................6

Clearances ...............................................................................................................................6

Gas Connection........................................................................................................................7

Typical Gas Line Connection....................................................................................................8

Gas Line Pipe Sizing ................................................................................................................9

Gas Pressure Check.................................................................................................................9

Log Assembly .........................................................................................................................10

Fireplace Screen ....................................................................................................................10

Millivolt System Control Options .............................................................................................11

Remote Control Information ...................................................................................................11

Lighting Instructions................................................................................................................12

Turning Off Gas to Appliance..................................................................................................12

Important Safeguards .............................................................................................................13

Match Lighting ........................................................................................................................13

Flame Check...........................................................................................................................13

Managing Heat Output ...........................................................................................................14

Maintenance

Cleaning..................................................................................................................................14

Troubleshooting ..........................................................................................................................15

Servicing ......................................................................................................................................15

Repair Parts .................................................................................................................................16

Warranty Information ..................................................................................................................17

Installation and Startup Checklist .............................................................................................18

Warranty Registration.................................................................................................................20

Table of Contents

Minimum Dimensions for Existing Solid Fuel Burning Fireplaces

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where not

prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for

use with other gases.

Opening Height = H

Opening Height Front Width Rear Width Depth

Hearth Size Table (H) (A) (B) (C)

VFL34RN 17” 26” 21” 11”

VFL34RP 17” 26” 21” 11”

78570

INSTALLER: Please leave these instructions with the

owner.

OWNER: Please retain these instructions for future

reference.

Important Information

WARNING: Any change to this heater or its con-

trols can be dangerous.

IMPORTANT: READ THESE INSTRUCTIONS CARE-

FULLY BEFORE INSTALLING.

WARNING: Do not allow fans to blow directly into

the fireplace. Avoid any drafts that alter burner

flame patterns.

WARNING: Do not use a blower insert, heat exchanger

insert or other accessory not approved for use with this

heater.

WARNING: This appliance is for installation only

in a solid-fuel burning masonry or UL 127 factory-

built fireplace or in a listed ventless firebox enclo-

sure. It has been designed certified for these

installations. Exception: DO NOT install this

appliance in a factory-built fireplace that includes

instructions stating it has not been tested or

should not be used with unvented gas logs.

NOTES

•Due to high temperatures, the appliance should be

located out of traffic and away from furniture and draper-

ies.

•Installation and repair should be done by an experienced

and qualified service person or gas appliance installer.

•The appliance must be inspected before use and at least

annually by a professional service person. More frequent

cleaning may be required due to excessive lint from

carpeting, bedding material, dust and pet hair, etc. It is

important that the control compartment, burners and

circulating air passageways of the appliance be kept clean.

Refer to instructions on Page 14.

•DO NOT place clothing or other flammable material on or

near the appliance.

•This appliance must only be used with pressures at the inlet

as shown in Table 1, page 9. Failure to check and document

these pressures may void the warranty.

•The installation must conform with local codes or, in the

absence of local codes, with the NATIONAL FUEL GAS CODE,

ANSI Z223, latest edition. If you cannot reference these codes,

DO NOT attempt to install this unit.

•Any safety screen or guard removed for servicing an

appliance must be replaced prior to operating the heater.

•The appliance and its appliance main gas valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2 psig (3.5 kpa).

•The appliance must be isolated from the gas supply piping

system by closing its equipment shut-off valve during any

testing of the gas supply piping system at test pressures equal

to or less than 1/2 psig (3.5kpa).

•DO NOT use this heater in recreational vehicles, bedrooms or

bathrooms.

•If this is the ONLY gas appliance, we recommend a

minimum 200 pound cylinder with a fill gauge. Use of a 100

pound cylinder is not recommended. Other household gas

appliances may require the tank size to be larger. Do not

operate the vent-free heater if the fuel level in the propane

tank is below 1/4 full.

•DO NOT use this heater if any part of it has been submerged

under water. Immediately call a qualified technician to inspect

the appliance and replace any part of the control system and

any gas control which has been under water.

•Any outside air ducts in the fireplace shall be permanently

closed at the time of appliance installation.

•Check local, state or city codes to determine if unvented

heaters are permitted. If unvented heaters are not permit-

ted, the fireplace chimney damper must be fixed at a

minimum free (vent) opening area of 15 sq. ins. This must

be accomplished by a clamp or screw on the chimney

damper to stop at the minimum vent area. The fireplace

must also have a minimum free (vent) opening of 15 sq.

ins. (Fig. 1)

•This appliance may be installed in an after-market* manufac-

tured "mobile" home where not prohibited by state or local

codes.

*After-market: Completion of sale, not for purpose of re-sale

from the manufacturer.

•OUTSIDE AIR DAMPER OR ASH DUMP (IF PRESENT)

MUST BE CLOSED AND SEALED.

•Young children should be carefully supervised when they

are in the same room as the appliance.

WARNING: During manufacturing, fabricating and

shipping, various components of this appliance are

treated with certain oils, films or bonding agents. These

chemicals are not harmful but may produce annoying

smoke and smells as they are burned off during the

initial operation of the appliance, possibly causing

headaches and eye/lung irritation. This is a normal and

temporary occurrence.

Input (BTU/hr) BTU/hr

Model Fuel Hi Lo

VFL34RN Natural 34,000 22,000

VFL34RP LP/Propane 34,000 25,500

•An unvented room heater having an input rating of more

than 10,000 btu per hour shall not be installed in a bedroom

or a bathroom.

For Installation of High Altitude

When installing this fireplace at an elevation above 2,000 feet

(in the United States), it may be necessary to decrease the

input rating by changing the existing burner orifice to a smaller

size. Input should be reduced four percent (4%) for each 1,000

feet above sea level, unless the heating value of the gas has

been reduced, in which case this general rule will not apply. To

identify the proper orifice size, check with the local gas utility.

Consult your local gas utility for assistance in determining the

proper orifice for your location.

78570

Provisions for Adequate Combustion and Ventilation Air

The National Fuel Gas Code, ANSI Z223.1

defines a

confined space as a space whose volume is less

than 50 cubic feet per 1,000 Btu per hour (4.8m3per

kw) of the aggregate input rating of all appliances

installed in that space and an unconfined space as a

space whose volume is not less than 50 cubic feet

per 1,000 Btu per hour (4.8 m3per kw) of the aggre-

gate input rating of all appliances installed in that

space. Rooms communicating directly with the

space in which the appliances are installed, through

openings not furnished with doors, are considered a

part of the unconfined space.

WARNING: This heater shall not be installed in a

confined space or unusually tight construction unless

provisions are provided for adequate combustion

ventilation air.

Today's homes are built more energy efficient than ever. New

materials, increased insulation and new construction methods

help reduce heat loss in homes. Home owners weather strip

and caulk around windows and doors to keep the cold air out

and the warm air in. During heating months, home owners

want their homes as airtight as possible.

While it is good to make your home energy efficient, you need

fresh air. All fuel-burning appliances need fresh air for proper

combustion.

Supplying Adequate Ventilation

This appliance must be installed in an unconfined space.

The following information will help you classify your space

and provide adequate ventilation for complete combustion.

An Unconfined Space has a minimum volume of 50 cubic

feet for each 1000 BTU/Hr input rating of all appliances in the

space. (4.8 M3per kw), (cubic feet equals length x width x

height of space).

A Confined Space has a volume of less than 50 cubic feet

for each 1000 BTU/Hr input rating of all appliances in the

space, (4.8M3per kw), (cubic feet equals length x width x

height of space).

Determining if You Have a Confined or

Unconfined Space

Use this worksheet to determine if you have a confined or

unconfined space.

Space: Includes the room in which you will install heater plus

any adjoining rooms with doorless passageways or ventilation

grills between the rooms.

1. Determine the volume of the space (length x width x

height).

Length x Width x Height = _____cu. ft. (volume of space)

Example: Space size 25’ (length) x 25’ (width) x 8’ (ceiling

height) = 5,000 cu. ft. (volume of space)

If additional ventilation from adjoining room(s) is supplied

with grills or doorless openings, add the volume of these

rooms to compute the total volume of the applicable

space.

2. Divide the space volume by 50 cubic feet to determine the

maximum BTU/Hr the space can support.

________(volume of space) ÷50 cu. ft. = (Maximum BTU/

Hr the space can support.

Example:

5,000 cu. ft. (volume of space) ÷50 cu. ft. = 100

or 100,000 (maximum BTU/Hr the space can support)

3. Add the BTU/Hr of all gas burning appliances in the space.

Gas range BTU/Hr

Vented gas heater BTU/Hr

Gas fireplace logs BTU/Hr

Other gas appliances* + BTU/Hr

Total = BTU/Hr

Example:

Gas range 60,000 BTU/Hr

Vent-free logs + 29,000 BTU/Hr

Total = 89,000 BTU/Hr

*Do not include direct-vent gas appliances. Direct-vent draws

combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum BTU/Hr the space can support

with the actual amount of BTU/Hr used.

__________ BTU/Hr (maximum the space can support)

__________ BTU/Hr (actual amount of BTU/Hr used)

Example:

100,000 BTU/Hr (max. the space can support)

89,000 BTU/Hr (actual amount of BTU/Hr

used)

The space in the above example is an unconfined space

because the actual BTU/Hr used is less than the maximum

BTU/Hr the space can support. If the space had been

confined, your options would be as follows:

A. Rework worksheet, adding the space of an adjoining

room. If the extra space provides an unconfined

space, remove door to adjoining room or add ventila-

tion grills between rooms. See Ventilation Air From

Inside Building.

B. Install a lower BTU/Hr heater, if lower BTU/Hr size

makes room unconfined.

Converting Confined Space to Unconfined

Space

Additional volume to convert a confined to an unconfined

space could come from an adjoining space. When using an

adjoining space, you can provide two permanent openings:

one within 12" of the ceiling and one within 12" of the floor on

the wall connecting the two spaces (see options 1 and 3,

Figure 2), or remove the door into the adjoining room.

Ventilation Air From Outdoors for Unusu-

ally Tight Construction

WARNING: If the area in which the heater may be

operated is smaller than that defined as an unconfined

space or if the building is of unusually tight construction,

provide adequate combustion and ventilation air by one

of the methods described in the National Fuel Gas Code,

ANSI Z223.1/NFPA 54, Section 5.3 or applicable local

codes.

78570

Unusually tight construction is defined as construction

where:

a. walls and ceilings exposed to the outside atmosphere have

a continuous water vapor retarder with a rating of one perm

(6 X 10.11 kg per pa-sec-m2) or less with openings gasketed

or sealed and

b. weather stripping has been added on openable windows

and doors and

c. caulking or sealants are applied to areas such as joints

around window and door frames, between sole plates and

floors, between wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical and gas lines and at

other openings.

If your home meets all of the three criteria above, you must

provide additional fresh air.

You may provide two permanent openings: one within 12" of

the ceiling and one within 12" of the floor. Connect these items

directly to the outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National

Fuel Gas Code NFPA 54/ANSI Z223.1, Section 5.3, Air for

Combustion and Ventilation

for required size of ventilation grills

or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into

attic if attic has a thermostat-controlled power vent. Heated air

entering the attic will activate the power vent.

Flue Damper Closed for Unvented

Operation and Maximum Heat

Output

Flue Damper Locked Open

to a Minimum Free (Vent)

Opening of 15 sq. in., (for

areas where unvented

products are not permitted)

NOTE: For round flue opening,

minimum flue diameter (d) = 5”. For

square or rectangular opening,

length x width (L x W) must equal 15

sq. in.

T104

Fig. 1 Minimum flue diameter and flue damper positions.

Option 1 -

Vents to

Adjoining

Room

Option 2 -

Remove

Door to

Adjoining

Room

Option 3 -

Vents to

Adjoining

Room

12”

VO370-2

Fig. 2 Ventilation options for confined space.

WARNING: Air openings that

provide fresh air from an adjoin-

ing unconfined space shall not be

blocked or obstructed in any way.

Installation of unit should allow a

minimum of 2" clearance from any

part of the heater to any of the

ventilation openings.

78570

Installation

Unpacking

Open the carton and remove the logs and the chassis. Re-

move each of the logs by gripping at either end of the log while

avoiding any undue pressure. Please note that the logs have

been marked for positive identification.

The carton for all models contains the following: grate/burner

assembly, front and rear logs, 2 top twigs, 2 screws, a bag of

volcanic ash and a bag of embers.

Fireplace Preparation

The fireplace needs to be prepared before installing the unit:

A. Turn off the gas supply if the gas line has been run to the

fireplace.

B. WARNING: Before installing logs in fireplace, the

chimney flue and firebox must be cleaned of soot,

creosote, ashes and loose paint by a qualified chimney

cleaner or sooting will occur.

Note: If your fireplace has been cleaned using chemicals or

solvents, these products may have been absorbed into the

fireplace hearth and walls and will be burned off during the

initial break-in period.

C. Any outside air ducts and/or ash dumps in the fireplace shall

be permanently closed and sealed at the time of appliance

installation. This will prevent drafts from disturbing the

flames and interfering with complete combustion of the gas

fuel.

Location

When gas logs are to be installed in a fireplace, inspect the

area surrounding it for possible air drafts that may affect the

flames and possibly cause sooting. Such drafts may be caused

by a ceiling fan near the fireplace, a hot air furnace register or

an open door. When burning the logs, carefully observe the

effect of possible drafts on the flames and take appropriate

measures to eliminate them. For example, the ceiling fan may

be cut off, the hot air register closed, etc.

Centrally locate the gas logs in the fireplace deep enough into

the firepit to accomplish an adequate draft (if use as a vented

appliance is planned). Ensure that the front feet of the grate sit

inside the front edge of the fireplace. Be sure fireplace meets

minimum fireplace dimensions.

To avoid any movement of the unit during operation, screw

the chassis to the floor of the fireplace using the screws

provided. Failure to do so could cause gas leaks.

Holes are provided in the sheet metal chassis (Fig. 3) and

should be used for securing the log set. After locating the

chassis correctly in the fireplace, mark the hole positions on the

fireplace floor. Drill two 1/8” diameter holes approximately 1/2”

deep.

Use the two screws to secure the chassis to the fireplace floor.

(Fig. 3)

Clearances

NOTE: The following instructions regarding installation clear-

ances and the use and installation of a canopy apply to use of

the appliances as an unvented space heater in permitting

jurisdictions. When installed as a vented decorative gas

appliance, the clearances noted below and the use of a heat-

deflecting canopy are not required.

However, it is recommended that these instructions be followed

even when the appliance will be used as a vented decorative

appliance in case local codes change to allow unvented space

heaters or in the event that the flue damper is inadvertently

closed.

Clearances for unvented installation in existing fireplaces,

(jurisdiction permitting)

1. Sidewall Clearances: Clearances from the side of the

fireplace opening to any combustible wall should not be less

than 2”. (Fig. 4A and 4B)

2. Ceiling Clearances: The ceiling height should not be less

than 62" from the top of the fireplace opening. (Fig. 4A)

3. Mantel Clearances: The use of a canopy* is optional

depending on mantel clearances to the fireplace opening

and projection profile.

NOTE: Mantel clearances may differ for each vent-free

firebox. Refer to the firebox installation instructions for

clearances.

A. Mantel profile: The minimum distance above the

fireplace opening to combustible material projecting 1¹⁄₂"

(tile moldings, breast boards, etc.) is 12¹⁄₂".

Combustible material projecting 6" (a mantel shelf, for

example) requires a minimum clearance of 19" above the

fireplace opening. Required clearance varies with the

amount of projection. (Fig. 4C)

The mantel profile must fall within the cross-section

shown in Figures 4C or 4D.

B. Heat resistant material: Any heat resistant material

suitable for a continuous operating temperature of 120°C

(248°F) must cover the wall surface directly above the

fireplace opening and extend the full width of the

fireplace opening for a distance of 10" above the

opening. (Fig. 4C)

Fig. 3 Use two (2) screws to secure the chassis to the fireplace

floor.

T131a

78570

Gas Connection

Check Gas Type. Use only the gas type indicated on the

heater's rating plate. If the gas type indicated on the plate is not

your type of gas supply, DO NOT INSTALL. Contact your

dealer for the proper model.

WARNING

DANGER OF PROPERTY DAMAGE,

BODILY INJURY OR DEATH.

Make sure the heater is equipped to operate on

the type of gas available. Models designated as

natural gas are to be used with natural gas only.

Heaters designated for use with liquefied petro-

leum (l.p.) gas have orifices sized for commer-

cially pure propane gas. They cannot be used

with butane or a mixture of butane and propane.

Gas Piping. The gas supply line must be of an adequate size

to handle the BTU/HR requirements and length of the run for

the unit being installed.

Determine the minimum pipe size from the piping size chart on

Page 9. The normal gas connection at this appliance is 1/2"

NPT made at the left of the unit.

Always use an external regulator for all LP installations to reduce

the supply tank pressure to a maximum of 14" w.c. This is in

addition to the regulator fitted to the heater.

WARNING: Connecting directly to an unregulated

LP tank can cause an explosion.

All piping must comply with local codes and ordinances or with

the National Fuel Gas Code (ANSI Z223.1), whichever applies.

Gas Line Connection

NOTE: These models are factory equipped with a stainless

steel flex tube connected to the control valve gas line inlet.

The inlet to these units is 1/2” NPT.

If installation is for L.P. gas, have L.P. installer use two-stage

regulation and make all connections from storage tank to

heater. Refer to the National Fuel Gas Code for the proper

supply tank size with the Btu's/Hr requirements. If this is the

ONLY gas appliance, we recommend a minimum 200 pound

cylinder with a fill gauge. Use of a 100 pound cylinder is not

recommended. Other household gas appliances may require

the tank size to be larger.

Use two pipe wrenches when making the connection to the

valve to prevent turning or damage to gas valve or regulator.

Connection between the manual shut-off valve and the gas

valve can be made with a CSA design certified flexible connec-

tor if allowed by local codes. A drip leg (sediment trap) must

be installed. (Fig. 5) Tighten all joints securely.

CAUTION: Failure to install a drip leg (sediment trap) may

result in improper combustion that will produce soot.

Reference Sections 3.7 and 5.5.7 and Figure 5.5.7 of the

National Fuel Gas Code for guidance.

62"

Fig. 4A Minimum clearance to wall and ceiling.

10"

1¹⁄₈"

10"

Min.

15"

Min.

19"

Min.

23"

Min.

27"

Min.

Heat Resistant

Material

No Canopy Used

Fig. 4C Mantel clearances (single or multi-sided opening

fireplaces).

Fireplace Opening

Fireplace

Opening

Maximum Projection:

7”

2” Minimum

Clearance

Mantel Leg

Combustible Mantel

Noncombustible

Facing

Mantel Leg

Fig. 4B Side clearances and projection.

10"

1¹⁄₈"

Min.

12"

Min.

16"

Min.

20"

Min.

Heat Resistant

Material

Fig. 4C Mantel clearance with Optional Universal Canopy.

Fireplace Opening

Universal

Canopy

Fireplace Hearth

Level

78570

Typical Gas Line Connection

Step 1: With the engine assembly free from the fireplace,

check tightness of flexible connector fittings.

CAUTION: Use one wrench to hold regulator and one

wrench to loosen and tighten the brass fittings. Failure to

hold the regulator while loosening and tightening the

fittings can damage the unit and cause gas leaks.

Step 2: Set the engine assembly into the fireplace and connect

the flexible connector to the gas piping that has been installed

per local codes, or in the absence of local codes, ANSI Z223.1

latest edition.

Step 3: After the last connection is made, screw the engine

assembly to the bottom of the fireplace. (Fig. 3)

Step 4: Test all connections for gas leaks.

Fig. 5 Typical drip leg (sediment trap) configurations.

Less Than 6’

If using flexible

connector, check local

codes for specific

requirements

Piped Gas Supply

Drop

Manual Shut-Off Valve Horizontal

Ground Joint

Union

Tee

Fitting

Nipple

3”

Min.

Cap

1/8” N.P.T. Plugged

Hole for Test Gauge

Gas

Valve

Drop

Manual Shut-Off

Valve

Ground Joint

Union

Tee

Fitting

Nipple

3”

Min.

Cap

1/8” N.P.T.

Plugged Hole

for Test Gauge

Gas

Valve

Tubing Gas Supply

Riser

Manual Shut-Off

Valve

Ground Joint

Union

Tee

Fitting

Nipple 3”

Min.

Cap

1/8” N.P.T.

Plugged Hole

for Test Gauge

Gas

Valve

Riser

Horizontal

Piped Gas Supply

All bends in metallic tubing should be

smooth, elbows are recommended.

CAUTION: Shut off the main gas supply before removing

end cap to prevent gas from filling the work area. Test for

gas leakage when installation is complete.

T130

Under no circumstances should internally zinc alloy coated piping be used. According to the LP-Gas Code and National Fuel Gas

Code - If galvanized piping is used, it must be EXTERNALLY coated only! Galvanized water pipe used for gas installations will

result in reduced gas pressure and gas leaks.

78570

NOTE: To determine the size of the branch gas line from the main gas line to the fireplace, enter the tables below (for iron

pipe or copper tubing) using the distance from the gas meter or second stage regulator to the furthest appliance on the

gas system. Select a pipe or tube diameter which has enough capacity to meet the maximum input requirement of the

fireplace. Regardless, do not use less than 1/2" diameter for the branch line. For any distances required longer than

shown in these tables, refer to the National Fuel Gas Code.

NOTE: There may be a local gas utility requirement specifying a minimum diameter for gas piping. All units require a 1/2 inch pipe

connection at the gas valve.

Gas Line Pipe Sizing

CAPACITY OF PIPING

Cubic Feet per Hour based on 0.3" w.c. Pressure Drop

Specific Gravity for Natural Gas - 0.6 (1000 BTU/Cubic Foot)

Specific Gravity for Propane Gas - 1.6 (2550 BTU/Cubic Foot)

Length Nominal Inches for Iron Pipe Sizes (1,000s BTU/hr)

of 1/2” D 3/4” D 1” D 1¹⁄₄” D 1¹⁄₂” D

Pipe Natural Propane Natural Propane Natural Propane Natural Propane Natural Propane

20’ 92 143 190 296 350 546 730 1135 1100 1711

30’ 73 115 152 237 285 444 590 918 890 1385

40’ 63 97 130 202 245 380 500 778 760 1183

50’ 56 87 115 179 215 334 440 683 670 1043

60’ 50 79 105 163 196 304 400 622 610 949

70’ 46 71 96 151 180 280 370 576 560 872

90’ 40 61 84 130 160 250 320 497 490 763

100’ 38 59 79 122 150 235 305 474 460 717

Outside Diameter Copper Tubing, Type L (1,000s BTU/hr)

Tubing Length 1/2” 5/8” 3/4” 7/8”

Feet 0.43 0.545 0.666 0.785

10 110 206 348 536

20 76 141 239 368

30 61 114 192 296

40 52 97 164 256

50 46 86 146 224

60 42 78 132 203

80 36 67 113 174

100 32 59 100 154

WARNING: Use only internally tinned copper tubing. If correct copper tubing is not used, tubing can deteriorate and develop

gas leaks.

Table 1

Gas Inlet Pressure Natural Propane

Max. 14.0” w.c. 14.0” w.c.

Normal 7.0” w.c. 11.0” w.c.

Min.* 5.0” w.c. 10.8” w.c.

Regulator Pressure 3.5” w.c. 10.0” w.c.

*Minimum inlet supply pressure for the purpose of input adjustment.

Gas Pressure Check

The gas inlet pressure specified in Table 1 is the pressure

where the field-installed gas line connects to the gas control.

This is measured at the inlet test port on the gas valve in the

appliance. Ensure that pressure is as shown in Table 1.

The manifold pressure is controlled by the gas valve and should

be checked at the pressure test points as shown in Figure 9 on

Page 11. The pressure connections accept 1/4” I.D. hose or

tubing.

The pressure should be checked with the appliance burning on

high (highest setting) and all other appliances turned on. One

must then read the manometer and if pressures are not 10.0”

w.c. for LP or 3.5” w.c. for Natural gas the inlet pressure must

be adjusted or increased until the proper pressures are at-

tained. If these pressures are greater than 10.2” w.c. for LP or

3.7” w.c. for Natural gas, contact your gas supplier before

operating the appliance.

Pressure is tested by loosening (do not remove) the screw in

the test port and sliding tubing onto the test port.

CAUTION: If the appliance's operating pressures are not

checked and adjusted, improper combustion may result in

soot being produced. Record the results of the gas

pressure check on the appropriate documents.

Testing The Gas Piping. Test all piping for leaks. When

checking gas piping to the heater with gas pressure less than

1/2 PSI, shut off manual gas valve for the heater. If gas piping

is to be checked with the pressure at or above 1/2 PSI, the

heater and manual shut off valve must be disconnected during

testing to prevent damage to the regulator on the unit. (SEE

WARNING).

To ensure that the gas lines and connections do not have any

leaks, a pressure test should be performed. Only a qualified

installer should perform the pressure test to ensure that

the unit is not damaged by high pressures!

WARNING: Be sure that the gas type indicated on the

gas log rating plate concurs with the gas system in your

building.

78570

If you connect natural gas to an LP gas unit, you may be

unable to ignite the pilot. If the pilot does ignite, the burner

flame on the low setting will be bright blue but only 1/4” to 1/2”

long and most likely lifting off the burner ports. If this is the

case, turn the unit off immediately.

If you connect LP gas to a natural gas unit, the burner flame

on the low setting will be about 6” - 8” long. On the high setting,

the burner flames will be bright yellow and about 10” in length.

Turn the unit off immediately! If the unit is allowed to run in

this condition, substantial amounts of soot will be generated

and emitted into the house.

Log Assembly

Refer to Figures 6, 7 and 8

1. Remove logs from carton and inspect.

2. Rear log should be installed onto rear log supports. Match

up slots on rear of log with the vertical log bracket tabs. (Fig.

3. Place the bottom edge of the large front log between the two

tabs located in the log support channel which centers the log

left to right. (Fig. 6)

4. The two top twigs can then be placed in their designated

positions located with pins on back logs and grooves on the

front log. (Fig. 7)

5. Lava rock from the bag provided should be placed on the

hearth pan area to suit individual appearance preferences.

DO NOT place volcanic ash on burner, pilot or logs.

6. Platinum embers are to be placed only on top of the front

burner port area. Equally space emblers one layer thick.

Do not pile ember material over one layer thick as this

does not enhance the “ember” appearance or improve

the log set performance. (Fig. 8)

7. Flames must not impinge (touch) on logs.

WARNING: Do not use more embers than those supplied with

your unit. Do not use embers other than genuine “Platinum

Embers” supplied by Temco Fireplace Products - Part No.

78037.

When you have completed these steps, compare log positions

with Figure 7. The logs must be positioned as illustrated.

CAUTION: Proper location is critical. When positioning the log

set, make sure that the logs do not interfere with the sides of

the fireplace before securing the chassis.

Fireplace Screen

A fireplace screen must be in place when the appliance

is operating and unless other provisions for combustion air

are made, the screen must have openings for the introduction

of combustion air.

Rear Log Supports

Support

Channel & Tabs T131

Fig. 6 Match up slots on rear of log with vertical log bracket

tabs.

Fig. 7 Correct log placement.

Rear Log Right Twig

Left Twig Front Log

TL106

Platinum Ember TL107

Fig. 8 Platinum ember placement.

WARNING: Failure to position the parts in accordance

with this diagram or failure to use only parts specifically

approved with this heater may result in property damage

or personal injury. See instruction manual for further

information.

78570

Millivolt System Control Options

Burner ON/OFF Control

Several options are available to turn the burner ON/OFF. These

options include: WRD-1 standard ON/OFF remote, WRST-K

thermostatically controlled remote, WSW Millivolt wall switch or

GFPMT Millivolt wall thermostat.

For installation of these options, detailed instructions are

provided with each kit.

CAUTION: If a remote receiver is located in the gas control

area (under the firebox), clearance should be below the firebox

at least two (2) inches to avoid high temperatures (receiver

should not be exposed to temperatures exceeding 130°F). The

log set should not be modified to accept any other type of

remote control as no guarantee may be made regarding proper

function. Refer to remote manufacturer’s instructions for battery

replacement.

IMPORTANT: If connecting a wall switch, thermostat or remote

control, use only the top and bottom control valve terminals for

attachment of the wire leads (do not use center terminal of

terminal block). (Figs. 9 and 10)

Remote Control Information

The remote receiver does not need to be secured to the

VFL34R(N,P) base, but can be placed along side of the log/

base assembly, (larger fireboxes only) in a wall mounted switch

box, or placed near the logset on the fireplace hearth exten-

sion.

Recommended Maximum Lead Length (Double Wire)

When Using Wall Switch or Thermostat

Wire Size Maximum Length

14 ga. 50’

16 ga. 32’

18 ga. 20’

20 ga. 15’

22 ga. 10’

NOTE: Must be stranded wire.

Fig. 9 Optional wiring to wall switch.

T114

A Thermopile (Do not

remove)

B Switch (OFF/ON)

C Wires from receiver (red &

white) or wires from millivolt

wall

Fig. 10 Control valve terminal block.

Front Grate Bar

HI/LO Flame Control

ON/OFF Switch

ON/PILOT/OFF Control

Piezo

Front Grate Leg T132

Fig. 11 Logset controls.

Logset Control Location and

Component Identification

78570

For Your Safety, Read Before Lighting

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,

personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE OPERATION smell all around the appliance

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any tele-

phone in your building.

•Immediately call your gas supplier from a neighbor's

telephone.

•Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire depart-

ment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand,

don't try to repair it. Call a qualified service technician.

Force or attempted repair may cause a fire or an explosion.

D. Do not use this appliance if any part of it has been under

water. Immediately call a qualified service technician to

inspect the appliance and to replace any part of the control

system or gas control which has been under water.

E. Be sure both the receiver and the remote have had a 9 volt

battery installed in each.

To Turn OFF Gas to Appliance

Depress the control knob slightly and turn it clockwise to the OFF position. Refer to Figure 12.

Lighting Instructions

1. STOP! Read the safety information above before proceed-

ing.

2. Refer to Figure 12. To turn

off the gas supply, depress

the knob slightly and turn

clockwise to the

OFF position.

3. Wait five (5) minutes to

clear out any gas. Then

smell for gas, including

near the floor. If you smell

gas, STOP! Follow “B” in

the safety information

above. If you don’t smell gas, go to the next step.

4. Refer to Figure 13. Locate the pilot. It is positioned on the

burner behind the front log and below the right twig.

times. This will cause a spark at the pilot which will ignite

the pilot gas.

7. Hold the control knob for 20 seconds to prevent the flame

failure detector from shutting off the gas while its probe is

warming up.

8. Release the control knob.

•If the knob does not pop up when released, stop and

immediately call your service technician.

•If the pilot will not stay lit after several tries, turn the gas

control knob to OFF and call your service technician or gas

supplier.

9. Refer to Figure 16. When the pilot remains lit, turn the

control knob counterclockwise to the ON position.

10. Flame adjustment is

controlled by using the HI/LO

flame control knob (located to

the right of the ON/OFF pilot

control knob).

11. This appliance is fitted with

a pilot burner for the purpose of

safe ignition of the main burner

in conjunction with the piezo

ignitor. The pilot, in operation

with the main burner contributes

to the base heat release and is

turned off by turning the control knob to the OFF position.

12.Lighting Instructions for Millivolt Wall Switch. After the

pilot is lit and the control knob is released, the wall switch

can be switched to turn the unit “ON” or switched to turn it

“OFF”. Refer to Page 11 for wiring.

Natural

Gas Propane

T122a

Fig. 13

5. Refer to Figure 14. Push in the control knob and turn

counterclockwise to the PILOT position. Hold the

control knob in for a few

seconds.

6. While still holding in the

control knob, press the

ignitor push-button several

ON PILOT

OFF

Fig. 14

Push in

to Light

Pilot

Turn Knob Counterclockwise

ON PILOT

OFF

Turn Knob

Clockwise

Fig. 12

T133

Fig. 15

Piezo

ON PILOT

OFF

Turn Knob

Counterclockwise

Fig. 16

78570

Important Safeguards

Although your gas logs are very realistic in appearance it

is not a real wood-burning fireplace and must be used for

burning rejected material.

To avoid irreparable damage to the appliance or personal

injury; matches, paper, garbage or any other material must not

be placed or thrown on top of the logs or into the flames.

To avoid personal injury, do not touch hot surfaces when

the appliance is operating.

Touch only the piezo button and control knob.Avoid contact

with the front screen, canopy or any other part which will be

very hot.

Always ensure that the fireplace screen is in place

when the appliance is operating.

Close supervision is necessary when the appliance is

being operated near children.

Do not use to cook food.

If this is the ONLY gas appliance, we recommend a minimum

200 pound cylinder with a fill gauge. Use of a 100 pound

cylinder is not recommended. Other household gas appliances

may require the tank size to be larger. Do not operate the vent

free fireplace if the fuel level in the propane tank is below 1/4

full.

This appliance is intended to be used only for supplemental

heat. Do not use it routinely as a primary heat source. Continu-

ous operation could produce excessive humidity depending on

construction characteristics and outdoor temperatures (below

200°F) Over time, this could cause condensation to form and

damage wall structures and exterior paint. Do not use this

product during building construction. Dust, debris, paint fumes

etc. can cause burner damage and/or produce strong odors.

If the fireplace is equipped with glass doors, the doors must be

fully open when the gas appliance is operating.

WARNING: The glowing ember base and all the logs are

manufactured from bonded ceramic fiber. This is a

commonly used material in industry worldwide. In the

event of the logs and base being removed, care should

be taken not to damage the bonded material.

Intentional misuse of, or deliberately fragmenting, the

material could lead to inhaling fibers and be injurious to

health. Insure the logs are properly positioned at all

times.

Match Lighting

If the pilot cannot be ignited with the piezo, it can be manually

lit with the use of a match and lighter rod.

1. Place the match in the holder and light. With the right

hand, depress and turn the control knob counterclockwise

to the PILOT position. Hold in for 20 seconds.

2. Take the lighter rod and lighted match and ignite the pilot.

3. Continue to hold the control knob for an additional 20

seconds to ensure pilot is maintained.

Flame Check

A periodic visual check of the flames should be made. The pilot

flame should always be present when the appliance is in

operation. (Fig. 17)

In normal operation (at full rate for approximately 15 minutes)

the following flame appearance should be observed:

The flame should burn blue with some yellow flames visible.

Height of the blue flame should be approximately 1” on high.

The yellow flames should extend 6 to 8 inches above the large

front log.

Typical flame shape seen in Figure 18.

NOTE: For your safety, the appliance is equipped with an

oxygen depletion system. The system senses the oxygen in the

atmosphere and switches off the gas supply in case the level of

oxygen falls below a safe level. It must not be altered in any

way.

1¹⁄₂"

Natural Gas Propane

T122

Fig. 17 Pilot flame position and location.

TL108

Fig. 18 Correct burner flame appearance.

Air Shutter Settings

Model A

VFL34RN Closed

VFL34RP 0.375”

T134

Fig. 19 Air shutter settings.

78570

Managing Heat Output

The heat output from the appliance can be controlled by the

position of the flue damper on vented fireplaces.

The damper setting should be fully closed for maximum heat

output, partially closed for less heat output and fully open for

minimum heat output.

The appliance may be used in a working solid fuel burning

fireplace with the fuel damper closed only if unvented appli-

ances are permitted by local state and city codes. It may also

be operated as a decorative appliance whose prime function

lies in the aesthetic effect of the flames when installed in a solid

fuel burning fireplace with the flue damper open. If unvented

heaters are not permitted, the fireplace vent damper must be

locked at a minimum free (vent) area of 15 sq. ins.

Whenever the appliance is operated with the fireplace's

flue damper closed, glass doors - if present - must be open

and the outside air damper and the ash dump (if the

fireplace is equipped with either one) must be closed.

The heat output from the appliance when operated as a vent-

free heater may be controlled by adjusting the main gas valve.

Reference lighting instructions on Page 11 and chart on Page 3

which shows inputs at all settings.

The main gas valve may be adjusted anywhere between high

and low to give the desired combination of flame aesthetics and

heat output.

Maintenance

Cleaning

CAUTION: Before cleaning or moving logs or other parts of the

unit, be sure to read the section on important safeguards.

Cleaning should be done before the logs are used each year

and after long periods of non-use. Professional servicing is

recommended.

All cleaning should be carried out when the appliance is cold.

Only limited cleaning will be required under normal use.

Dusting the front grate or the control knob panel may be

required occasionally. Do not use any cleaning fluids to clean

the logs or any other part of the appliance.

If the flames show any unusual shapes or behavior, or if the

burner(s) fail to ignite properly, then the burner holes may

require cleaning. If this occurs contact your nearest dealer to

get the appliance serviced.

Alternatively, the appliance can be cleaned by removing the

logs. Handle the logs gently so as not to damage them.

Always lift each log by holding it carefully at each end.

After the logs are removed allowing access to the burner area,

use the brush attachment from your vacuum cleaner to carefully

remove dust and loose particles from the base, logs and from

around the burner. Gloves are recommended when handling

the logs. Use extreme caution when cleaning around the pilot

(ODS). The pilot should not be moved or altered from the

original factory setting (Pilot to burner preset location). To clean

the pilot, take an Air Duster can (computer cleaner compressed

air) and insert the nozzle into the primary air inlet. Shoot a

short blast of air into the inlet to clear dust. (Fig. 20) The burner

should not be removed or taken out of it’s locked and secure

position (proper location of burners are critical).

Logs must be carefully replaced in their orignial, preset posi-

tions, as shown in Figure 21, to prevent the rear flames from

touching any log. No other arrangement is permitted. Incorrect

placement can diminish combustion efficiency and cause

sooting.

A qualified gas professional should periodically check and clean

the orifices and burners per National Fuel Gas Code, Appendix

Lack of proper maintenance may void warranty.

Gas

Outlet

Primary Air

Inlet

T135

Fig. 20 Use a short burst of air into the primary air inlet to clean

pilot.

Fig. 21 Correct log placement.

Rear Log Right Twig

Left Twig Front Log

TL106

78570

Troubleshooting

With proper installation and maintenance, your new gas

fireplace should provide years of trouble-free service. If you do

experience a problem, refer to the trouble shooting guide below.

This guide will assist you or a qualified service person in the

diagnosis of problems and the corrective action to be taken.

Any safety screen or guard removed for servicing an appliance

must be replaced prior to operating the appliance. Use only a

qualified service person when making repairs.

Symptom Possible Cause Corrective Action

1. Pilot will not light Air in gas line Purge gas lines and repeat ignition operation

Low gas pressure Check gas pressure

Gas supply turned off Turn on gas supply

Blockage in gas line Check gas passage way

ODS pilot orifice is clogged Call a qualified service person

Control knob not in pilot position Turn control knob to pilot position

Control knob not pressed in while Press in control knob while in pilot position

in pilot position

Ignitor did not spark Ignitor electrode positioned wrong Correct electrode position

Ignitor electrode broken Replace assembly

Ignitor cable pinched or broken Free ignitor cable, if damaged replace it

Ignitor cable not connected to ignitor Connect cable to ignitor

2. Pilot will not stay lit Partially clogged ODS pilot orifice Contact qualified service person or your gas company

Corrosion of thermocouple contact Clean thermocouple contact

Bad gas valve Replace gas valve

Control knob not pressed in long After pilot lights, keep control knob pressed in for

enough 60 seconds

Thermocouple connection loose at Tighten connection finger tight + 1/4 turn or replace

gas control or damaged thermocouple or replace ODS pilot assembly

Pilot flame not touching thermocouple Contact a qualified service person

3. Main burner will not light Low gas supply pressure Contact your gas supplier

Burner orifice clogged Clean burner orifice

Control knob not in ON position Turn control knob to ON position

4. Heater shuts off on ODS Not enough fresh air is available Open window

Low gas pressure Contact your gas supplier

ODS pilot partially lit Contact a qualified service person

Servicing

Repair and replacement work should only be done by a

qualified service technician. Always shut off the gas supply and make sure the appliance is

cool before beginning any service operation.

Always check for gas leaks after servicing.

78570

Repair Parts

Always include the correct name, part number, model number,

control type and serial number of the appliance when ordering

service parts. Refer to the parts list below.

Use manufacturer's authorized parts only. If you desire to

communicate with the factory, write to Customer Service at:

Temco Fireplace Products

410 Admiral Blvd.

Mississauga, Ontario

Canada L5T 2N6

Description VFL34RN VFLRP Qty.

Grate Assembly 78442 78442 1

Engine Base Assy 78574 78574 1

Side Deflector 78443 78443 1

Support Channel 78439 78439 1

Air Scoop 78445 78445 1

Valve - Natural 55463 - 1

Valve - LP/Propane - 55462 1

Burner - Natural 78474 - 1

Burner - LP/Propane - 78473 1

Pilot - Natural (OP) 78167 - 1

Pilot - LP/Propane (OP) - 78169 1

Manifold Tube/Split Nut 78456 78456 1

Orifice #31 - Natural 78458 - 1

Orifice #50 - LP/Propane - 78451 1

Tube, Flexible Gas Inlet 71598 71598 1

Tube, Pilot 3/16” 78583 78583 1

Ignitor w/Nut (Piezo) 65180 65180 1

Wire Assembly Rocker Switch 78596 78596 1

Mini Rocker Switch PCOA049 PCOA049 1

Shaft Extender 78568 78568 2

Knob, Black (1/4” Dia.D-Shaft) 78578 78578 2

Rod Adapter 78562 78562 2

Embers, Platinum (Bag) 78037 78037 1

Lava Gravel Assy 68688 68688 1

Front Log 76895 76895 1

Back Log 75317 75317 1

Log, Right Twig 75318 75318 1

Log, Left Twig 75319 75319 1

78570

Limited Warranty

TEMCO Fireplace Products Vent-Free Gas Fireplaces

This warranty is limited to TEMCO Fireplace Products

Vent-Free Gas Logs & Fireplaces (henceforth, Product)

manufactured by TEMCO Fireplace Products. (hence-

forth, TEMCO).

ONE YEAR WARRANTY

TEMCO warrants all components of the Product to be

free of defects in materials and workmanship for a period

of one year from the date of installation, with the excep-

tion of the warranty on logs and ember base. If, by the

sole determination of TEMCO, any component covered

under this warranty is found to be defective, TEMCO will,

at its option, repair or replace the defective component at

no charge and will pay labor cost incurred as specified in

the current TEMCO Labor Allowance Schedule, 71313. If

TEMCO determines replacement or repair is not eco-

nomically practical, TEMCO will, at its option, refund the

purchase price of the Product. Date of installation and

purchase price must be verified by acceptable proof of

purchase prior to warranty action.

This warranty covers only parts and labor as provided

above. In no case shall TEMCO be responsible for

materials, components or construction which are not

manufactured or supplied by TEMCO, or the labor

necessary to install, repair or remove such materials,

components or construction.

FIVE YEAR WARRANTY

TEMCO warrants the ceramic fiber and refractory compo-

nents and burners originally packed with the product to

be free of defects in material and workmanship for a

period of five (5) years from the date of installation, with

the exception of breakage. If any ceramic components or

refractory components are broken, such breakage must

be reported as a Warranty Claim at the time of installa-

tion. Breakage claims arising after the initial installation

will not be covered under any part of this warranty.

Periodic maintenance must have been performed.

QUALIFICATIONS

For the above warranties to apply:

The Product must be installed by a qualified installer;

strictly in accordance with TEMCO installation

instructions, and in compliance with local codes and

ordinances. The logs must be placed strictly in accor-

dance with the arrangement described in the installation

instructions.

The Product must be operated and maintained according

to the instructions furnished. Alteration of the Product

in any way is prohibited and voids any and all war-

ranties. Removal of the data plate alters the Products

and voids the warranty.

The installer must have completed the installation

and Startup Checklist, a copy of which must be

submitted along with proof of purchase, to obtain

prior approval for warranty repair or replacement and

to affect a warranty claim. The Checklist is found on

Pages 18 and 19 of this manual.

The limited warranty applies only to the original owner of

the Product or the original owner of the dwelling in which

the Product was installed. Use of any parts other than

genuine factory provided replacement parts shall void

this warranty.

Limitations

TEMCO is not responsible for any incidental or conse-

quential damages caused by possible defects in the

Product. The duration of any implied warranty with

respect to the Product is limited to the duration of the

foregoing warranties.

Some states and provinces do not allow exclusion of

incidental or consequential damages or limits on the

duration of implied warranties, so these limitations may

not apply to you.

Warranty Fulfillment

Claims require specific agreement and consent from

TEMCO Technical Services prior to performing any

warranty repair or replacement. TEMCO reserves the

right to investigate any and all warranty claims. The

appliance must not be removed prior to such investiga-

tion other than on direction from TEMCO.

Please provide the following information when communi-

cating with TEMCO Technical Services, its Dealers or

Distributors regarding service under this warranty.

TEMCO reserves the right to decide on the method of

settlement (if any). This limited warranty is given in lieu of

any other expressed or implied warranty, and supersedes

all other TEMCO Product warranties.

Model Number: ____________________

Serial Number: _____________________

Date of Installation: ____/____/____

Purchased From: ___________________

78570

TEMCO FIREPLACE PRODUCTS GAS LOGS & FIREPLACES

INSTALLATION AND STARTUP CHECKLIST

Customer Copy

NOTE: TEMCO Fireplace Products gas logs and fireplaces require installation by a qualified gas appliance installer.

A copy of this checklist must be submitted, along with proof of purchase, when applying to Technical Services for prior

written approval of warranty repair or replacement.

All Vent-Free Gas Fireplaces and Logs

Read and understand installation instructions before attempting installation.

Assure that the model to be installed is of the CORRECT FUELTYPE. Check markings on the shipping container (Model #’s

ending in “N” are natural gas products; models #’s ending in “P” are LP gas products.), tags on the burner assembly.

NOTES: REGULATORS ARE NOT FIELD-ADJUSTABLE. ANYATTEMPT TO ADJUST VOIDS THIS WARRANTY.

In order to ensure adequate combustion air, make sure that the model being installed has the appropriate heating

capacity for the unconfined space available. Allow a minimum of 50 cubic feet of unconfined space per 1000 BTU’s for all

gas appliances.

Assure that gas line size is adequate for the model’s input rating (BTU’s per hour), the length of run from the meter or

second stage regulator to the farthest gas appliance, and other gas appliances on the system. A drip leg or sediment trap is

required. LP models require a minimum tank size of 120 gallons water capacity and two stage regulation.

Assure that installation meets local codes and ordinances.

Assure that there are no fans or blowers in the fireplace area.

Check for leaks before lighting.

Using a manometer, verify proper gas pressure at the manifold with unit at maximum setting and other appliances

operating.

inlet pressure: _______ (ins. wc) manifold pressure: ________ (ins. wc)

Verify proper ignition of ODS and front and rear burners, as well as proper appearance of flames.

Verify that ceramic fiber and refractory components are properly positioned and secure. (Rear burner must not

contact logs.)

Verify adequate clearance to mantels and other combustibles.

Demonstrate correct operation of the product to the consumer. NOTE: LP models must not be operated if fuel tank is less

than 1/4 full.

Observe the consumer operating the product properly.

Explain and demonstrate proper periodic maintenance.

Explain that operation with logs positioned other than as described in the manual voids the warranty and will cause poor

combustion and sooting.

Verify the consumer’s understanding that warranty service work that is not pre-approved by the manufacturer’s Technical

Service Department (other than routine maintenance) may not qualify for reimbursement.

Answer any questions the consumer may have about TEMCO Fireplace Products vent-free products.

Vent-Free Gas Logs Only

Verify that the fireplace in which the logs are to be installed is either a solid-fuel burning fireplace (either factory-built or

masonry) with a working flue system connected to it or an approved vent-free firebox.

Verify that the fireplace has been thoroughly cleaned by a professional chimney sweep. If solvents have been used to clean

the hearth, they must be allowed to evaporate before proceeding with installation.

Check firebox dimensions for adequate height, width, and depth.

Verify that the grate assembly is attached to the firebox floor.

Verify that any ash dump or outside air inlets are permanently sealed to avoid drafts within the firebox.

Verify that no additional logs, ornaments or non-approved blower devices have been added.

Repair any broken or damaged logs prior to operation.

Check mantel clearances and verify installation of canopy if necessary.

Glass doors must be removed or opened completely during operation of logs.

Please sign below that checklist has been completed and understood. DATE INSTALLED ____/____/____

Installer Phone Consumer Phone

78570

TEMCO FIREPLACE PRODUCTS GAS LOGS & FIREPLACES

INSTALLATION AND STARTUP CHECKLIST

Installer’s Copy