TEXONIC RX 800 User manual

RX 800
OWNERS MANUAL
SOURCE INPUTS
4 5LINKLINK
RX800
6 SOURCE/4 Z0NE
Audio Distribution Amplifier
(2 x Streamer Inside)

2

3
The RX 800 home audio system brings you the advanced Generation D
technology, it is a functional, easy-to-install, highly compatible, expandable
and used-friendly audio distribution system. With few simple steps to install, it
provides up to 50Wx2 power by class D amplifier and distribute at most to 12
zones which all can be controlled by packaged keypads, IR remote controller
or APP.
Simply connecting the RX 800 to the local Ethernet network, it let you access
a wide variety of music from the Built-in streaming services or stored on the
Smartphones. Two USB ports on the front panel for playing music files from
USB storage devices. An Optical digital input to manage the sound of a flat
screen or a CD player to have high resolution of sound quality in each zone.
The overall distribution system including package device is easy-to-install, so
every audiophile in every zone can use IR controller or keypads to enjoy the
powerful audio. High functionality and performance bring you musical
enjoyment just the way you want it.
INTRODUCTION
FEATURE
* Each zone provides 50Wx2 (@ 4 Ohm) output power.
* High efficiency more than 85% Class D amplification.
* 6 Line input sources, including 2 Audio Streamers (Input 4, 5).
* USB ports for playing music files from USB Flash Drive (Input 4, 5).
* Each zone Stereo/Mono output selectable.
* Enable control over Ethernet.
* Support Control APP.
* PRE-AMP output on Zone1~4.
* Built-in IR receiver & IR remote controller for Source
select/Volume/Treble/Bass.
* 12V DC trigger output to external device when the system is power on.
* 12V DC mute trigger input from the external devices.
* RJ45 Ethernet port for the wired connection to the local network.
* Another RJ45 Ethernet expansion port for connecting with smart TV or other
device.
* RS-232 port allows 2-way communication with the Home Automation system.
* Expandable up to 12 Zones by additional 2 units.
* 4 LEDs for 4 zones Power On, Standby and Mute.
* Built in IR emitter.
* AC 115V / 230V input power switchable.

4
SPECIFICATION
Output Power:
Output Power:
Output Power:
S/N:
THD:
Frequency Response:
Input Impedance:
Input Sensitivity:
Protection Function:
System on Voltage:
External Mute Voltage:
Power Supply:
Output Connection:
Input Connection:
Sampling Rate(Streamer):
Audio Format(USB):
Streamer Support:
USB type:
Network:
Dimension:
Weight:
25W x 2 per zone (at 8Ω)
50W x 2 per zone (at 4Ω)
100W per zone (Bridged at 8Ω)
>85dB A WTD
<0.1%
20Hz-20KHz
>47 K Ohm
250 mV
Overload, Short Circuit
DC +12V
DC +12V
AC115V/60Hz, 230V/50Hz
4P Terminal Block
Input 1, 2 - RCA Jacks
Input 3 - 3.5mm Jack, S/PDIF
Input 4,5 - Streamers or USB ports
Input 6 - RJ-45. For connecting with MAP-KBT1,
MAP-KSP1, MAP-KWS1.
24Bit / 48KHz
MP3/WMA/AAC/AAC+/ALAC/FLAC/APE/WAV
DLNA, AirPlay
USB2.0, Support up to 64G.
RJ45, Standard 10/100Mb
430mm x 89mm x 416 mm (WxHxD)
8.7KG

5
1. Power ON/OFF/ STANDBY
Depress the power button to turn
on the system. Press it again to
release the latch and power the
unit off. Note that even the Master
Controller is powered on, each
zone will remain in Standby mode
until the zone keypad is activated.
SOURCE INPUTS
4 5LINKLINK
RX800
13 14 17 26 7 8 9 15
1 3 5 4 10
12
11 16
REAR PANEL
1. PRE-AMP OUTPUT
Stereo Line level output on each zone.
Connect to additional amplifier with higher
output, or powered Sub-woofers.
2.SPEAKER OUTPUTS
Removable terminal block connectors on
each zone.
Each zone provides 2x50W @ 4 Ohm or
100W @ 8 Ohm in bridge mode.
3.STEREO/BRIDGE SWITCH
4.SOURCE INPUTS
6 Stereo Analog/Digital inputs.
Two Streamers are input 4 and 5.
5.Input 1/PA
Paging capability for Input 1 to broadcast to all
zones when 12VDC is applied to the PA - IN jack.
6.STATUS
When the zone is activated, the corresponding
jack will output 12VDC to trigger other device.
7.IR EMI TTER S
IR Outputs 4 routed & 1 common
8.PA-IN
12VDC paging trigger input
9.EXT. MUTE/CONTROL OUT
Mute the entire system with the 12VDC MUTE IN.
Use the12VDC CONTROL OUT to trigger other
equipment
2. Standby/Zone ON LED
These four LEDs illuminate to indicate the
status of each zone.
Blue: In Standby mode.
White: In Activate mode.
Blue/White: In Mute mode.
3. USB Port 4/5
Two USB ports correspond to the built-in
Streamers, as source input 4 and 5. Playing
audio source from USB Flash Drives.
1 2 3
FRONT PANEL

6
1
3
5
6
7
2
7
4
10.EXPANSION IN/OUT PORT
Expandable to 12 zones with 3 x Multi-zone
Controller systems.
11.ETHERNET PORTS
Dual LAN ports, one connects to the LAN
port of local router. Another connects to
network TV or other device which requires
Ethernet.
12.ETHERNET/RS232 SWITCH
ETHERNET: When the amplifier connects to
Ethernet.
RS232: When the amplifier control by PC or
Control Device via RS-232.
13.AGC
Automatic Gain Control, brings low level
up to a present-level.
14.MASTER/SLAVE SWITCH
Set the unit ID when connecting multi
Controller systems
15.KEYPAD
RJ-45 jack Connects to the keypad hub
for 4 keypads.
16.VOLTAGE SELECT
Please set to correctly input voltage
before turn on the amplifier.
17.AC INPUT

7
1
7
2
5
6
3
4
3

8
RX 800
RX 800
RCA 3.5mm Stereo

KEYPADS 1 KEYPADS 2 KEYPADS 3 KEYPADS 4
The RX 800 can work with speakers that are 4-8 Ohm. There are two
modes that can be set for different setups: Stereo or Bridge. An 8 Ohm
speaker can only be used when in Bridge mode. To choose between modes,
use the mode switch to determine modes for each zone (Number 2 Panel
Descriptions, page 5)
9
and network.
STEREO MODE BRIDGE MODE

The RX 800 comes with 4 POE enabled keypads. This allows for source control
from each specific zone as well as IR routing to the appropriate source devices
once selected. The MAP-800US also comes with a hub that allows for all
6-keypads to be connected to the amp via Cat5e/6.
10
ZONE-1
ON ON OFF
1 2 3
ZONE-2
ON ONOFF
1 2 3
ZONE-3
ON OFFOFF
1 2 3
ZONE-4
ONONOFF
1 2 3

11
RX 800
FRONT BACK
reserved for cascading units
12VDC out to trigger
external amplifier
four four

12
four
4

When being used with keypads, the RX 800 can receive IR signals from each
zone, and routed back through the Cat5e/6 and Keypad up to the Amplifier to
control the selected source. For example, if Source 2-DVD is selected in Zone 1,
the user will be able to control the DVD player to power the device on/off,
change settings ect. Since the amplifer has discreet routing, ONLY the Source
that is selected on each zone can be controlled. This prevents other sources
from accidently be controlled when selected on other zones.
The RX 800 can allow 6 sources to be distributed to up to 12 zones on 3
different units using the provided ribbon cable to connect between units. To do
this first each unit needs to be addressed according using the MASTER/SLAVE
switch. There are 3 positions for this, Master, Slave 1, and Slave 2 which help
identify each unit.
13
Source 2-DVD
IR Emitter from
Source 2 port
Power
IR Signal
Grounding
IR +
IR -

14
In this mode, only connect all sources to the MASTER unit, and share these
sources to Slav 1 and Slave 2 units. And the original source inputs on Slav 1 and
Slave 2 will be disabled.
Master
SLAVE 1
SLAVE 2

ETHERNET CONNECTION
15
Network TV
Router
APP
There are two RJ-45 jacks on the rear panel of this amplifier for the connection to
Ethernet.
Please use a good quality Cat5e/5 cable, and follow the connecting diagram
below.
1.Connect the LAN1 port on the rear panel of controller to the local Wi-Fi Router.
The Ethernet connection mainly for Wi-Fi control via APP or other control devices.
2.Connect the LAN2 port on the rear panel of control to the smart TV or other
Network devices.
The port simply works as SWITCH function as long as the LAN1 port enabled to
Ethernet.
Note: When controlling via ETHERNET, please make sure the ETHERNET/RS232
switch is set at ETHERNET position.

SOURCE INPUTS
4 5LINKLINK
CONNECTION DIAGRAM
12V Trigger
output
MAP-800HD
Network TV
Router
APP
DVD
Stereo Amplifier
or
Powered
Subwoofer
16

17
The RX 800 and APP are easy to install and connect to the local network, simply
connect the RJ-45 IN port to the router via Cat5 cable, and also make sure your
smart devices connect to the same local network. After connecting the RX 800
to the router by Cat5 cable, the controller will connect with the local network
automatically.
In case, having the problem for connecting to the network, please check the
position of switches on the rear panel.
INTEGRATED NETWORK
1.Open the IE web browser of PC, log in to the WEB configuration page of local
Router to find the IP address of RX 800 (shown as below)
Please switch to MASTER and ETHERNET.
Note. Please do not press “Reset” button.
Note. Please do not connect the Ethernet port of RX 800 to the computer
directly.
RX 800

18
2. Using “Advanced_IP_Scanner” software to find the IP address.
Please visit www.advanced-ip-scanner.com for free download.
Then enter the IP address of RX 800 to the IE browser (shown as below), ensure
the Serial Configure is 9600,n,8,1. After finishing this step, RX 800 could be
controlled through the local Network.

Download free software “PuTTY” Tool from the internet to control the device.
Operation diagram as below:
FOR CONTROLLING VIA OTHER SOFTWARE
19

Click Telnet, enter the IP address of RX 800 and port: 8080.
Click Open.
When the IP address connected, the operation diagram shows as below:
Key in the command code to control RX 800.
For the detail of command codes, please find the RS-232 command codes in this
instruction manual.
20