The Original Pink Box PB408SV User manual

VACVACVAC
120 VOLT120 VOLT120 VOLT
WET / DRYWET / DRYWET / DRY
OPERATOR’S
MANUAL
FOR YOUR SAFETY
– Read and understand this manual before use. –
– Keep this manual for future reference. –
4 Gallon / 15.14 Liter
Part No. PB408SV

The Cala Industries 1-Year warranty are warranted to be free from defects in materials and
workmanship for 1-Year after the date of purchase by the original owner of the product. If
this product is defective, please call Cala Industries at 888-350-2252. Cala Industries shall
not be liable for any damage for loss of the product or consequential damages of any kind.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND
ALL INSTRUCTIONS
LIMITED 1 YEAR WARRANTY
TABLE OF CONTENTS
2
Thank you for purchasing this The Original PinkBox Professional Wet / Dry vacuum cleaner.
Feel condent that with The Original PinkBox you are obtaining a high quality product
engineered for optimal performance. This vacuum is capable of picking up liquids and dry
materials.
SECTION PAGE
Warranty............................................................................................................................................................................... 2
Safety Instructions and Warnings............................................................................................................................... 3
Double Insulation Instructions .................................................................................................................................... 4
Extension Cord................................................................................................................................................................... 4
Unpacking and Checking Carton Contents ............................................................................................................ 5
General Assembly Instructions .................................................................................................................................... 6
Dry Vacuuming Operation............................................................................................................................................. 7
Liquid Vacuuming Operation....................................................................................................................................... 8
Blowing Operation ........................................................................................................................................................... 9
Maintenance....................................................................................................................................................................... 9
Installing & Cleaning cartridge filter ........................................................................................................................10
Installing & Cleaning Foam Sleeve Filter................................................................................................................10
Troubleshooting..............................................................................................................................................................11
Exploded View and Parts List......................................................................................................................................12
MANUFACTURED FOR:
CALA Industries • 1555 Fayette St • El Cajon, CA 92020
Toll Free: 888-350-2252
www.theoriginalpinkbox.com

SAFETY INSTRUCTIONS & WARNINGS
3
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all instructions before using this vacuum.
Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before
operating.
Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use
this Wet/Dry Vac only as described in this manual.
To reduce the risk of personal injury or damage to your Wet/Dry Vac, use only The Original PinkBox
recommended accessories.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
CAUTION:
If safety information is not followed someone may be injured.
When using an electrical appliance, basic precautions should always be followed including
the following:
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK ORINJURY
• Do not run vac unattended.
• Do not vacuum, or use this Wet/Dry Vac near flammable liquids, gases, or explosive vapors like gasoline or other fuels, lighter
fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal dust, magnesium dust, grain dust, or gun
power. Sparks inside the motor can ignite flammable vapors or dust.
• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Keep cord away from heated surfaces.
• Do not expose to rain. Store indoors.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not use with damaged cord, plug or other parts.
• If your Wet/Dry Vac is not working as it should, has missing parts, has been dropped or damaged, left outdoors or dropped
into water, return it to an independent service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners.
• Do not run Wet/Dry Vac over cord.
• Do not handle plug or the Wet/Dry Vac with wet hands.
• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.
• Do not use or store near hazardous materials.
• Do not use this Wet/Dry Vac with a torn filter or without the filter installed except when vacuuming liquids as described in the
operation section of this manual.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.
• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and before servicing.
• Turn off Wet/Dry Vac before unplugging.
• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked; keep free of dust,
lint, hair or anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. • To reduce the risk of falls, use
extra care when cleaning on stairs.
WHEN USING AS BLOWER:
• Direct air discharge only at work area.
• Do not use Wet/Dry Vac as a sprayer.
• Do not direct air at bystanders.
• Keep children away when blowing

DOUBLE INSULATION INSTRUCTIONS
EXTENSION CORDS
4
This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use
only identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry
Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following
warnings that appear on the motor housing of your Wet/Dry Vac.
DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE
ONLY IDENTICAL REPLACEMENT PARTS.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN. STORE INDOORS.
WARNING: FOR YOUR OWN SAFETY, READ AND UNDERSTAND OPERATOR’S MANUAL. DO NOT RUN
UNATTENDED. DO NOT PICK UP HOT ASHES, COALS, TOXIC, FLAMMABLE OR OTHER HAZARDOUS
MATERIALS, DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS.
CAUTION: Do not vacuum drywall dust or fireplace soot or ash with standard
Wet/Dry filter. This type of dust is very fine which may not be captured by the filter and cause
damage to motor. When vacuuming fine dust use a fine dust filter.
WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUM WITH A
DOUBLE-INSULATED WET/DRY VACUUM, TWO SYSTEMS OF INSULATION ARE PROVIDED INSTEAD OF
GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A DOUBLE-INSULATED APPLIANCE, NOR SHOULD A
MEANS FOR GROUNDING BE ADDED. SERVICING A DOUBLE NSULATED WET/DRY VACUUM REQUIRES
EXTREME CARE AND KNOWLEDGE OF THE SYSTEM, AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE
PERSONNEL. REPLACEMENT PARTS FOR A DOUBLE-INSULATED WET/DRY VACUUM MUST BE IDENTICAL TO
THE PARTS THEY REPLACE. YOUR DOUBLE-INSULATED WET/DRY VAC IS MARKED WITH THE WORDS
‘DOUBLE INSULATED’ AND THE SYMBOL (SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE
APPLIANCE.
• To reduce the risk of electric shock-unplug before cleaning or servicing.
• DO NOT use without filters in place.
CAUTION:TO REDUCE THE RISK OF INJURY FROM MOVING PARTS- UNPLUG BEFORE SERVICING
When using an extension cord with your Wet/Dry Vac refer to the following table to determine the required A.W.G. wire size.
Before using the cleaner make sure the power cord and extension cord are in good working conditions. Make repairs or
replacements before using the vacuum cleaner. Only use extension cords that are rated for outdoor use.

UNPACKING & CHECKING CARTON CONTENTS
5
Remove entire contents of carton. Check
each item against the carton contents.
Carton Contents List
Key Description
A 1PC Vac Assembly
B 1PC Hose
C 1PC Utility nozzle
D 1PC Crevice Tool
E 1PC Cartridge Filter
F 1PC Filter Retainer
G 1PC Dust Bag
H 1PC Foam Sleeve Filter
I 1PC Air/Noise Diffuser
NOTE: The hose and accessories for this
vacuum are 1- 7/8 inch (38 mm) diameter.

GENERAL ASSEMBLY INSTRUCTIONS
6
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG
IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC.
UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY
1. Verify that the power cord is disconnected from the outlet. (fig. 1)
2. Undo the latches. (g. 2)
3. Lift the power head off the container. (g. 3)
4. Remove the contents from inside the container, make sure you have all contents as listed on
page 5. (g. 4)
5. Your vacuum comes ready for dry vacuum cleaning. If cartridge filter is not installed refer to
page 10 for filter installation. (g. 5 & 6)
6. For wet vacuum cleaning, install the supplied foam filter. (g. 7) See page 10 for filter
installation.
7. Place the power head back on the container, aligning the top section with the latches, and snap
into place. (g. 8)
8. Secure the large end of the hose onto the vacuum port on the container and screw into place.
(g. 9)
9. Choose the desired accessories and insert onto the end of the hose. (g. 10)
AIR / NOISE DIFFUSER:
To diffuse exhaust air or for quieter operation, install
the noise diffuser into the blower port by turning
clockwise to lock into place.
POLARIZED PLUG:
To reduce the risk of electrical shock, this appliance has a polarized plug (one with the blade wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper
outlet. Do not change the plug in any way. Double insulation eliminates the need for the three
wire grounded power cord and grounded power supply system.

(DRY ) VACUUM OPERATION
7
WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION,
ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES,
VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED
TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL
SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO; COAL, MAGNESIUM, GRAIN OR GUN
POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST, DO NOT VACUUM TOXIC
MATERIALS.
OPERATING INSTRUCTIONS — DRY VACUUMING:
1. Verify that the power cord is disconnected from the outlet. (g. 1)
2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely
mounted. Make sure the filter is pushed in until it stops against the power head. (g. 2) (Your
Wet/Dry Vac comes with the cartridge filter pre-installed, if not, see page 10 for installation
instructions.)
3. Place filter retainer on top of cartridge filter and tighten by turning the retainer handle
clockwise. (g. 3)
4. Optional, for improved dust filtering, fit collection dust bag flange onto the inlet stub, taking
care not to damage the bag. (g. 4)
5. Place the power head back on the container, aligning the top section with the latches, and lock
into place. (g. 5)
6. Insert the locking end of the hose into the vacuum port and screw in place. Push the desired
extension wands or attachments onto the free end of the hose. (g. 6)
7. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet.
(fig. 7 & 8
8. Turn the motor on by pressing the switch to the ‘I’ ON position. (g. 9)
9. Once you have completed vacuuming, press the switch to the ‘O’ OFF position and unplug the
power cord from the outlet. (g. 10 & 11)
O= OFF I= ON
DO NOT USE THE CARTRIDGE FILTER AND THE DUST
COLLECTION BAG FOR LIQUID VACUUMING.

(LIQUID ) VACUUM OPERATION
8
WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION,
ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES,
VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED
TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL
SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO; COAL, MAGNESIUM, GRAIN OR GUN
POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST, DO NOT VACUUM TOXIC
MATERIALS.
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG
IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC.
OPERATING INSTRUCTIONS — WET VACUUMING:
1. Verify that the power cord is disconnected from the outlet. Verify that the container is clean
and free of dust and dirt. (g. 1)
2. Remove cartridge filter and the dust collection bag, then carefully install the foam sleeve filter
over the filter cage and place the power head back on the container. (g. 2) See lter installing
instructions on page 10.
3. Fit the desired extension wands or nozzle to the vacuum hose. (g. 3)
4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet.
(g. 4 & 5)
5. Turn the motor on by pressing the switch to the ‘I’ ON position. (g. 6)
6. After use, flip the switch to the ‘O’ OFF position and unplug the power cord from the outlet.
(g. 7 & 8)
7. Empty the container into a suitable receptacle or drain. (g. 9)
IMPORTANT:
When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid;
leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float
valve that stops the suction action when the container reaches its maximum capacity. You will
notice an increase in motor speed. When this happens, turn off the machine, disconnect from
power supply, and drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit
the container with power head. After wet vacuuming, turn the machine off and remove plug from
power supply. Empty the container, clean and dry the inside and outside before storage.
REMEMBER! The foam lter must be removed after wet vacuuming,
and a cartridge lter must be installed before dry vacuuming again.

OPERATING INSTRUCTIONS — BLOWING OPERATION:
1. Verify that the power cord is disconnected from the outlet. (g. 1)
2. Make sure the container is empty and the dust collection bag is removed before using as a
blower.
3. Remove hose from the vacuum port.
4. Remove noise diffuser from blower port. (g. 2)
5. Insert the larger end of the hose into the blowing port on the back side of the power head. (g. 3)
6. Fit the desired attachment to the hose. (g. 4)
7. Ensure the power switch is turned off and plug into the power supply. (g. 5)
8. Before turning on the vac, firmly hold loose end of the hose. Turn the motor on by pressing the
switch to the ‘I’ ON position. (g. 6)
1. Verify that the power cord is disconnected from the outlet. (fig. 1)
2. Disconnect the hose from the vacuum. (fig. 2)
3. Undo the latches and remove the power head from the container. (fig. 3)
4. Clear all dirt or debris from the container and hose. (fig. 4)
5. Clean the foam filter by washing it with water and mild soap. (fig. 5)
6. Check the hose, attachments, and power cord to verify that they have not been damaged.
IMPORTANT! Clean or change the dust filter regularly for best performance. ALWAYS USE DUST
FILTER FOR DRY VACUUMING. If the machine is used without the cartridge filter, the motor will
burn out and the warranty will be voided. Always keep spare filters on-hand. (cont. on next page)
BLOWING OPERATION
MAINTENANCE
9
This Wet/Dry Vac has blowing capabilities only when the hose is inserted into the blowing port. To
use the blower feature follow the instructions listed.
ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH ANSI Z87.1 (OR IN CANADA,
CSAZ94.3) BEFORE USING BLOWER.
WARNING:
KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.
WARNING:
WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED.
WARNING:

INSTALLING CARTRIDGE FILTER:
1. Verify that the power cord is disconnected from the outlet. (g. 1)
2. Remove power head and place in upside down position.
3. Install the cartridge filter over the filter cage and carefully push filter in until it stops against the
power head. (g. 2 & 3)
4. Place filter retainer on top of cartridge filter and tighten down by turning retainer clockwise.
(g. 4 & 5)
REMOVING AND CLEANING CARTRIDGE FILTER:
1. Unlock and remove the filter retainer by turning retainer handle counter clockwise.
2. Carefully hold and pull the cartridge filter up for removal. (g. 6)
3. Clean the cartridge filter by gently tapping or brushing dirt off. Cleaning should not be done
indoors in living areas. For optimal performance a new filter is recommended.
INSTALLING FOAM SLEEVE FILTER:
1. Verify that the power cord is disconnected from the outlet. (g.1)
2. Remove power head and place in upside down position. Follow instructions to remove
cartridge filter.
3. Carefully slide foam sleeve filter down over the filter cage making sure the whole cage is
covered. (g. 2 & 3)
4. Replace the power head on to the container.
CLEANING FOAM SLEEVE FILTER
1. With the removed power head in the upside down position, carefully remove foam sleeve filter. (g. 4)
2. Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water. (g. 5)
3. Allow filter to air dry before installing and using again.
NOTICE! The filters included are made of high quality material designed to stop small dust
particles. The cartridge filter should be used for dry pick-up only. A dry cartridge filter is necessary
to pick up dust. If the cartridge filter is wet, it will clog quickly and be very difficult to clean. Handle
the filter carefully when removing it for cleaning and replacing it. Check the filters for tears or small
holes, a small hole can let dust pass through and out of the cleaner. Do not use a filter with holes
or tears in it, replace it immediately.
MAINTENANCE cont.
INSTALLING & CLEANING THE CARTRIDGE FILTER
INSTALLING & CLEANING FOAM SLEEVE FILTER
10
ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE REMOVING
THE POWER HEAD FROM CONTAINER.
WARNING:

TROUBLESHOOTING
11
WARNING:
Symptom Possible Causes Corrective Actions
TO REDUCE THE RISK OF ELECTRIC SHOCK - UNPLUG BEFORE
TROUBLESHOOTING.
Vacuum will not
operate.
1. No power supply. 1. Check power supply – cord,
breakers, fuses.
Dust coming from
motor cover.
1. Attach or replace the
Cartridge filter
1. Cartridge filter is missing or
damaged.
Reduced eciency
and motor/speed
vibration.
1. Check nozzle, hose and inlets
or blockage. Take off the
filter and clean it, or install
new filter.
1. There is a blockage in the
nozzle, hose, or the vacuum
inlets. Or the dust filter is
blocked by fine dust.
3. Container full. 3. Empty container.
2. Faulty power cord. 2. Unplug and check the power
cord. If damaged, have it
repaired by a professional.

EXPLODED VIEW AND PARTS LIST
12