TLS Electronics 875150 User manual

User manual
875150
HDBaseT Set 100
HDMI USB RS232 IR

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 2
Table of contents
Table of contents................................................................................................2
Safety and Notice ..............................................................................................3
Introduction........................................................................................................4
Applications .......................................................................................................4
System Requirements .......................................................................................4
Features.............................................................................................................5
Panel Description...............................................................................................6
Transmitter Front ............................................................................................6
Transmitter Rear.............................................................................................7
Receiver Front................................................................................................8
Receiver Rear.................................................................................................9
Connection Diagram........................................................................................10
Specifications................................................................................................... 11
Firmware Update:............................................................................................12
Package Contents ...........................................................................................13
Maintenance....................................................................................................13
Warranty Policy................................................................................................13
Limitations of Warranty....................................................................................14
Exclusive Remedies ........................................................................................14
RMA Policy ......................................................................................................15
Standard Replacement....................................................................................15
Once you have obtained an RMA number.......................................................15
Please note:.....................................................................................................16
Warranty..........................................................................................................16
Return and RMA Policies.................................................................................16

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 3
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the life
of your equipment.
Safety and Notice
1) The transmission distances of HDMI over UTP cables are measured using
TE CONNECTIVITY 1427071-6
2)EIA/TIA-568-B termination for CAT cables is recommended for better
performance.
3) DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)
because there are 2 pairs swapped, this will make POE OVER-CURRENT
and damage POE components. Please use straight-through CAT cable (both
RJ45 headers are 568A or 568B standard).
4) It is recommended that power up the device after connections of source, sink
and CAT cable.
5) To reduce the interference among the unshielded twisted pairs of wires in
CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close
parallel proximity to mains power cables. Shielded CAT cables can be used
to improve EMI problems, which is worsen in long transmission.
6) Because the quality of the CAT cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality,
the actual transmission range is subject to one’s choice of CAT cables.
7) Do not substitute or use any other Power Supply other than the enclosed unit,
or a TLS approved Replacement Part. Doing so will void the warranty and
potentially expose the user to dangerous voltages resulting in an electrical
shock.
8) Do not disassemble the device for any reason. Doing so will void the
manufacturer’s warranty. Also, our unique case is an integral part of the
design of this unit and is responsible for cooling and circuitry shielding. Any
modifications to this case will potentially cause malfunction and product
failure.
9) Do not expose the device to water, moisture, or liquids. Possible electric
shock may result as well as failure of the unit to operate.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 4
Introduction
This Model allows HDMI signals to be transmitted over a Single CAT5e/6 cable.
This solution has the added features of RS232 and 2-way IR control
functionality over the same CAT5e/6 cable. It can extend 4K@60Hz YUV4:4:4
over a HDBaseT link and upto 100M.The slimmest HDBaseT design, making it
perfect to mount behind ultra thin TVs.
Note:
1) About POC
The POC function is designed for powering compatible TX or RX unit of TLS
ONLY. DO NOT connect it with any third party Power Over Ethernet
devices. Damage may result.
Applications
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
System Requirements
Input HDMI source equipment such as DVD/Blu-ray player,host PC/Laptop and
HDMI
Equipped output display (TV or monitor) with amplifier or active speakers.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 5
Features
Bandwidth up to 18Gbps, resolution up to 4K2K@60hz YUV 4:4:4
Transmit up to 150m under 1080p,100m under 4K
Support HDR10
Support KVM and USB2.0
Support Bi-directional wide band IR and RS232 Pass through
Support Dual POC (Receiver powered by transmitter or transmitter
powered by Receiver)
Support HDCP2.2/ HDCP1.4 Compliant
Support Copy local and remote EDID functionality
Supports audio extractor rate up to 192kHz
Support PCM7.1, Dolby, DTS
With micro USB port for firmware upgrade

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 6
Panel Description
Transmitter Front
①IR In: Connect to the supplied IR blaster cable for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be controlled.
②IR Out: Connect to the supplied IR blaster cable for IR signal transmission.
Place the IR blaster in direct line of sight of the equipment to be controlled.
③USB Type A for extension
④USB Type B for connection
⑤DIP Switch: Switch to“ 0 ”transmit upto 100m under 4K@60Hz.
Switch to“1”transmit upto 150m under 1080P@60Hz.(Before power on, TX and
RX must be selected to 0 or 1 at the same time. Please do not switch it in the
working process)
⑥EDID Switch: Switch to“0”copy EDID from display of receiver(remote EDID
mode).Switch to“1”copy EDID from loopout display of transmitter(local EDID
mode).
⑦Indicator of HDMI
⑧Indicator of power input
⑥Note: EDID copy function on transmitter do not support 150M long
distance, when it is long distance mode, the EDID only support 1080P@60Hz.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 7
Transmitter Rear
①DC 24V input
②Update: USB port to update the firmware
③RS232 in: Connect to a PC or laptop with phoenix terminal for
the transmission of RS232 commands
④HDBT out: Connect to the receiver unit with a single CAT5e/6 cable for
transmission of all data signals
⑤HDMI loop out: Connect to a HDMI equipped TV/Monitor for display of the
HDMI input source signal
⑥HDMI In: Connect to HDMI source equipment such as DVD or Blu-ray player
④Note: do not connect projector directly which will break HDBT port,
please contact us and require technical support for such application.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 8
Receiver Front
①IR Out: Connect to the supplied IR blaster cable for IR signal transmission.
Place the IR blaster in direct line of sight of the equipment to be controlled.
②IR In: Connect to the supplied IR blaster cable for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be controlled.
③USB Type A for extension
④DIP Switch: Switch to“0”transmit upto 100m under 4K@60Hz.
Switch to“1”transmit upto 150m under 1080P@60Hz.(Before power on, TX
and RX must be selected to 0 or 1 at the same time. Please do not switch it in
the working process)
⑤Audio Switch: Switch to“0”extract Audio and output.Switch to“1”close
extraction Audio output(analog audio and SPDIF).
⑥Indicator of HDMI
⑦Indicator of power input

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 9
Receiver Rear
①DC 24V input
②Update: USB port to update the firmware
③RS232 Out: Connect to the device that is to be controlled via phoenix terminal by
RS-232 commands
④HDBT in: Connect to the transmitter unit with a single CAT5e/6 cable for
transmission of all data signals
⑤HDMI output: Connect to a HDMI equipped TV/Monitor for display of the HDMI
input source signal
⑥SPDIF out
⑦Analog audio out

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de 11
Specifications
Operating Temperature Range
-5 to +40°C (23 to +104 °F)
Operating Humidity Range
5 to 90 % RH (no condensation)
Input Video Signal
0.5-1.0 volts p-p
Input DDC Signal
5 volts p-p (TTL)
Video Format Supported
DTV/HDTV;
4K/1080P/1080i/720P(50HZ)/576P/48
0P/576i/480i
Output Video
HDMI 2.0+HDCP1.4/2.2
Output Audio
Support PCM,DTS-HD, Dolby-HD
Maximum Transmission
Distance
150 meters for 1080P, 100 meters for
4K
Power Supply
24V1A
Poc
Power from TX to RX over Cat5/6 cable
Power Consumption
14Watts
Dimensions
172.4mmH×113.2mmW×24mmD
Mass (Main unit)
1.1Kg (Pairs)
NOTE:Specifications are subject to change without notice. Weight and dimensions are approximate.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de
12
Firmware Update:
①The user should use the CD in colorbox,read and install software in PC;
②Connect unit to PC with usb cable from micro usb port, click software to
select correct usb port:
(Note: if PC is unable to identify the correct usb port,please install the driver
from CD first)
③Type in “A2” in PORT and select PATH with update file then click UPDATA
wait for update till display “Succeed” in red frame:
(Note:please differentiate the firmware for TX and RX before upgrade)

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de
Package Contents
Main unit
24V1A DC power supply
1xIR TX unit
1xIR RX unit
2 Phoenix plugs for RS232 cable termination
1 USB-cable A-B
1 USB micro cable
2 mounting brackets
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or
benzene to clean this unit.
Warranty Policy
TLS electronics products are warranted against defects in material and
workmanship for two years from the date of shipment. During the warranty
period, TLS electronics will, at its option, repair or replace products that prove
to be defective. Repairs are warranted for the remainder of the original
warranty or a 90 day extended warranty, whichever is longer.
For equipment under warranty, the owner is responsible for freight to TLS
electronics and all related customs, taxes, tariffs, insurance, etc. TLS
electronics is responsible for the freight charges only for return of the equip-
ment from the factory to the owner. TLS electronics will return the equipment by
the same method (i.e., Air, Express, Surface) as the equipment was send to
TLS electronics.
All equipment returned for warranty repair must have a valid RMA number
issued prior to return and be marked clearly on the return packaging. TLS
electronics strongly recommends all equipment be returned in its original
packaging. TLS electronics obligations under this warranty are limited to repair
or replacement of failed parts, and the return shipment to the buyer of the
repaired or replaced parts.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de
14
Limitations of Warranty
The warranty does not apply to any part of a product that has been installed,
altered, repaired, or misused in any way that, in the opinion of TLS electronics,
would affect the reliability or detracts from the performance of any part of the
product, or is damaged as the result of use in a way or with equipment that had
not been previously approved by TLS electronics. The warranty does not apply
to any product or parts thereof where the serial number or the serial number of
any of its parts has been altered, defaced, or removed.
The warranty does not cover damage or loss incurred in transportation of the
product. The warranty does not cover replacement or repair necessitated by
loss or damage from any cause beyond the control of TLS electronics, such as
lightning or other natural and weather related events or wartime environments.
The warranty does not cover any labor involved in the removal and or
reinstallation of warranted equipment or parts on site, or any labor required to
diagnose the necessity for repair or replacement.
The warranty excludes any responsibility by TLS electronics for incidental or
consequential damages arising from the use of the equipment or products, or
forany inability to use them either separate from or in combination with any
other equipment or products. A fixed charge established for each product will
be imposed for all equipment returned for warranty repair where TLS
electronics cannot identify the cause of the reported failure.
Exclusive Remedies
TLS electronics’s warranty, as stated is in lieu of all other warranties, expressed,
implied, or statutory, including those of merchantability and fitness for a
particular purpose. The buyer shall pass on to any purchaser, lessee, or other
user of TLS electronics’s products, the aforementioned warranty, and shall
indemnify and hold harmless TLS electronics from any claims or liability of such
purchaser, lessee, or user based upon allegations that the buyer, its agents, or
employees have made additional warranties or representations as to product
preference or use. The remedies provided herein are the buyer’s sole and
exclusive remedies. TLS electronics shall not be liable for any direct, indirect,
special, incidental, or consequential damages, whether based on contract, tort,
or any other legal theory.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de
RMA Policy
When returning product to TLS electronics for any reason, the customer should
fill out the official RMA form to obtain a RMA number. Without the permission or
approval, TLS electronics will be no responsible for any return. This can be
initiated by emailing or calling your related sales.
All requests are processed within 48 hours.
Standard Replacement
For customers that agree to return defective product to TLS electronics first, a
Standard Replacement option is available.
An RMA number must first be issued by sales. This RMA number will need to
be referenced on the outside of the return shipment.
Upon receipt of the defective product, TLS electronics will, at its discretion,
either repair or replace the product and ship it out in the most expeditious
manner possible. Subject to availability, the replacement product will be
shipped on the business day following receipt of the defective product.
In the event the product returned to TLS electronics has been discontinued (i.e.
the product is no longer being manufactured by TLS electronics but is still
under warranty), TLS electronics will, at its discretion, either repair or replace
with recertified product.
Once you have obtained an RMA number
After obtaining an RMA number from TLS electronics, you must send the
product - freight prepaid - to TLS electronics. The TLS electronics RMA number
must be prominently displayed on the outside of your package. If you send your
product to TLS electronics without the RMA number prominently displayed on
the outside of the package, it will be returned to you unopened.
Please use a shipping company that can demonstrate proof of delivery. TLS
electronics does not accept responsibility for any lost shipments unless proof of
delivery to TLS electronics is provided.

875150 HDBaseT Set 100 HDMI USB RS232 IR
Relens GmbH Contact: info@tls-electronics.de
16
Please note:
Product shipped to TLS electronics must be properly packaged to prevent loss
or damage in transit.
Shipping your RMA to TLS electronics using regular mailing envelopes is not
acceptable, as they do not protect the product from damage during shipping.
TLS electronics will not repair or replace a module that is shipped in such a way
that the product is not properly protected. TLS electronics will not accept any
product that has been damaged as a result of accident, abuse, misuse, natural
or personal disaster, or any unauthorized disassemble, repair or modification.
Warranty
Warranty time is two year and from the date of original shipment. This warranty
shall be void if a serial number has been removed from the product.
Upon determination of a legitimate defect covered by this warranty and at TLS
sole discretion, user should bear the transport cost during the warranty.
If product is out of warranty then repair charge is required. Minimum repair
charge: 10% of the retail price plus the cost of failed components. We will
repair the failed product after repair cost has been approved by Customers and
proper financial arrangements are made. Customer must cover round trip ship-
ment expenses.
Return and RMA Policies
Shipments will not be receiver and processed for warranty repair/replacement
without an TLS electronics RMA(Return Materials Authorization).
Relens GmbH
Germany
33175 Bad Lippspringe
An der Eiche 4
+49 (05252) 270
info@tls-electronics.de
www.tls-electronics.de
Table of contents
Other TLS Electronics Switch manuals